Internet Engineering Task Force (IETF) X. Liu Request for Comments: 8294 Jabil Category: Standards Track Y. Qu ISSN: 2070-1721 Futurewei Technologies, Inc. A. Lindem Cisco Systems C. Hopps Deutsche Telekom L. Berger LabN Consulting, L.L.C. December 2017 Common YANG Data Types for the Routing Area Abstract This document defines a collection of common data types using the YANG data modeling language. These derived common types are designed to be imported by other modules defined in the routing area. Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 7841. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at https://www.rfc-editor.org/info/rfc8294. Liu, et al. Standards Track [Page 1] RFC 8294 Routing Area YANG Types December 2017 Copyright Notice Copyright (c) 2017 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction ....................................................3 1.1. Terminology ................................................3 2. Overview ........................................................3 3. IETF Routing Types YANG Module ..................................8 4. IANA Routing Types YANG Module .................................27 5. IANA Considerations ............................................37 5.1. IANA-Maintained iana-routing-types Module .................38 6. Security Considerations ........................................39 7. References .....................................................39 7.1. Normative References ......................................39 7.2. Informative References ....................................40 Acknowledgements ..................................................42 Authors' Addresses ................................................43 Liu, et al. Standards Track [Page 2] RFC 8294 Routing Area YANG Types December 2017 1. Introduction YANG [RFC6020] [RFC7950] is a data modeling language used to model configuration data, state data, Remote Procedure Calls, and notifications for network management protocols. The YANG language supports a small set of built-in data types and provides mechanisms to derive other types from the built-in types. This document introduces a collection of common data types derived from the built-in YANG data types. The derived types are designed to be the common types applicable for modeling in the routing area. 1.1. Terminology The terminology for describing YANG data models is found in [RFC7950]. 2. Overview This document defines two YANG modules for common routing types: ietf-routing-types and iana-routing-types. The only module imports (ietf-yang-types and ietf-inet-types; see Section 3) are from [RFC6991]. The ietf-routing-types module contains common routing types other than those corresponding directly to IANA mappings. These include the following: router-id Router Identifiers are commonly used to identify nodes in routing and other control-plane protocols. An example usage of router-id can be found in [OSPF-YANG]. route-target Route Targets (RTs) are commonly used to control the distribution of Virtual Routing and Forwarding (VRF) information (see [RFC4364]) in support of BGP/MPLS IP Virtual Private Networks (VPNs) and BGP/MPLS Ethernet VPNs [RFC7432]. An example usage can be found in [L2VPN-YANG]. ipv6-route-target IPv6 Route Targets are similar to standard Route Targets, except that they are IPv6 Address Specific BGP Extended Communities as described in [RFC5701]. An IPv6 Route Target is 20 octets and includes an IPv6 address as the global administrator. route-target-type This type defines the import and export rules of Route Targets, as described in Section 4.3.1 of [RFC4364]. Liu, et al. Standards Track [Page 3] RFC 8294 Routing Area YANG Types December 2017 route-distinguisher Route Distinguishers (RDs) are commonly used to identify separate routes in support of VPNs. For example, as described in [RFC4364], RDs are commonly used to identify independent VPNs and VRFs, and, more generally, to identify multiple routes to the same prefix. route-origin A Route Origin is commonly used to indicate the Site of Origin for VRF information (see [RFC4364]) in support of BGP/MPLS IP VPNs and BGP/MPLS Ethernet VPNs [RFC7432]. ipv6-route-origin An IPv6 Route Origin would also be used to indicate the Site of Origin for VRF information (see [RFC4364]) in support of VPNs. IPv6 Route Origins are IPv6 Address Specific BGP Extended Communities as described in [RFC5701]. An IPv6 Route Origin is 20 octets and includes an IPv6 address as the global administrator. ipv4-multicast-group-address This type defines the representation of an IPv4 multicast group address, which is in the range of 224.0.0.0 to 239.255.255.255. An example usage can be found in [PIM-YANG]. ipv6-multicast-group-address This type defines the representation of an IPv6 multicast group address, which is in the range of ff00::/8. An example usage can be found in [PIM-YANG]. ip-multicast-group-address This type represents an IP multicast group address and is IP version neutral. The format of the textual representation implies the IP version. An example usage can be found in [PIM-YANG]. ipv4-multicast-source-address This represents the IPv4 source address type for use in multicast control protocols. This type also allows the indication of wildcard sources, i.e., "*". An example of where this type may/will be used is [PIM-YANG]. ipv6-multicast-source-address This represents the IPv6 source address type for use in multicast control protocols. This type also allows the indication of wildcard sources, i.e., "*". An example of where this type may/will be used is [PIM-YANG]. Liu, et al. Standards Track [Page 4] RFC 8294 Routing Area YANG Types December 2017 bandwidth-ieee-float32 This represents the bandwidth in IEEE 754 floating-point 32-bit binary format [IEEE754]. It is commonly used in Traffic Engineering control-plane protocols. An example of where this type may/will be used is [OSPF-YANG]. link-access-type This type identifies the IGP link type. timer-multiplier This type is used in conjunction with a timer-value type. It is generally used to indicate the number of timer-value intervals that may expire before a specific event must occur. Examples of this include the arrival of any Bidirectional Forwarding Detection (BFD) packets (see [RFC5880] Section 6.8.4) or hello_interval [RFC3209]. timer-value-seconds16 This type covers timers that can be set in seconds, not set, or set to infinity. This type supports a range of values that can be represented in a uint16 (2 octets). timer-value-seconds32 This type covers timers that can be set in seconds, not set, or set to infinity. This type supports a range of values that can be represented in a uint32 (4 octets). timer-value-milliseconds This type covers timers that can be set in milliseconds, not set, or set to infinity. This type supports a range of values that can be represented in a uint32 (4 octets). percentage This type defines a percentage with a range of 0-100%. An example usage can be found in [BGP-Model]. timeticks64 This type is based on the timeticks type defined in [RFC6991] but with 64-bit precision. It represents the time in hundredths of a second between two epochs. An example usage can be found in [BGP-Model]. uint24 This type defines a 24-bit unsigned integer. An example usage can be found in [OSPF-YANG]. Liu, et al. Standards Track [Page 5] RFC 8294 Routing Area YANG Types December 2017 generalized-label This type represents a Generalized Label for Generalized Multiprotocol Label Switching (GMPLS) [RFC3471]. The Generalized Label does not identify its type, which is known from context. An example usage can be found in [TE-YANG]. mpls-label-special-purpose This type represents the special-purpose MPLS label values [RFC7274]. mpls-label-general-use The 20-bit label value in an MPLS label stack is specified in [RFC3032]. This label value does not include the encodings of Traffic Class and TTL (Time to Live). The label range specified by this type is for general use, with special-purpose MPLS label values excluded. mpls-label The 20-bit label value in an MPLS label stack is specified in [RFC3032]. This label value does not include the encodings of Traffic Class and TTL. The label range specified by this type covers the general-use values and the special-purpose label values. An example usage can be found in [MPLS-Base-YANG]. This document defines the following YANG groupings: mpls-label-stack This grouping defines a reusable collection of schema nodes representing an MPLS label stack [RFC3032]. vpn-route-targets This grouping defines a reusable collection of schema nodes representing Route Target import-export rules used in BGP-enabled VPNs [RFC4364] [RFC4664]. An example usage can be found in [L2VPN-YANG]. Liu, et al. Standards Track [Page 6] RFC 8294 Routing Area YANG Types December 2017 The iana-routing-types module contains common routing types corresponding directly to IANA mappings. These include the following: address-family This type defines values for use in Address Family identifiers. The values are based on the IANA "Address Family Numbers" registry [IANA-ADDRESS-FAMILY-REGISTRY]. An example usage can be found in [BGP-Model]. subsequent-address-family This type defines values for use in Subsequent Address Family Identifiers (SAFIs). The values are based on the IANA "Subsequent Address Family Identifiers (SAFI) Parameters" registry [IANA-SAFI-REGISTRY]. Liu, et al. Standards Track [Page 7] RFC 8294 Routing Area YANG Types December 2017 3. IETF Routing Types YANG Module file "ietf-routing-types@2017-12-04.yang" module ietf-routing-types { namespace "urn:ietf:params:xml:ns:yang:ietf-routing-types"; prefix rt-types; import ietf-yang-types { prefix yang; } import ietf-inet-types { prefix inet; } organization "IETF RTGWG - Routing Area Working Group"; contact "WG Web: WG List: Editors: Xufeng Liu Yingzhen Qu Acee Lindem Christian Hopps Lou Berger "; description "This module contains a collection of YANG data types considered generally useful for routing protocols. Copyright (c) 2017 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC 8294; see the RFC itself for full legal notices."; Liu, et al. Standards Track [Page 8] RFC 8294 Routing Area YANG Types December 2017 revision 2017-12-04 { description "Initial revision."; reference "RFC 8294: Common YANG Data Types for the Routing Area. Section 3."; } /*** Identities related to MPLS/GMPLS ***/ identity mpls-label-special-purpose-value { description "Base identity for deriving identities describing special-purpose Multiprotocol Label Switching (MPLS) label values."; reference "RFC 7274: Allocating and Retiring Special-Purpose MPLS Labels."; } identity ipv4-explicit-null-label { base mpls-label-special-purpose-value; description "This identity represents the IPv4 Explicit NULL Label."; reference "RFC 3032: MPLS Label Stack Encoding. Section 2.1."; } identity router-alert-label { base mpls-label-special-purpose-value; description "This identity represents the Router Alert Label."; reference "RFC 3032: MPLS Label Stack Encoding. Section 2.1."; } identity ipv6-explicit-null-label { base mpls-label-special-purpose-value; description "This identity represents the IPv6 Explicit NULL Label."; reference "RFC 3032: MPLS Label Stack Encoding. Section 2.1."; } Liu, et al. Standards Track [Page 9] RFC 8294 Routing Area YANG Types December 2017 identity implicit-null-label { base mpls-label-special-purpose-value; description "This identity represents the Implicit NULL Label."; reference "RFC 3032: MPLS Label Stack Encoding. Section 2.1."; } identity entropy-label-indicator { base mpls-label-special-purpose-value; description "This identity represents the Entropy Label Indicator."; reference "RFC 6790: The Use of Entropy Labels in MPLS Forwarding. Sections 3 and 10.1."; } identity gal-label { base mpls-label-special-purpose-value; description "This identity represents the Generic Associated Channel (G-ACh) Label (GAL)."; reference "RFC 5586: MPLS Generic Associated Channel. Sections 4 and 10."; } identity oam-alert-label { base mpls-label-special-purpose-value; description "This identity represents the OAM Alert Label."; reference "RFC 3429: Assignment of the 'OAM Alert Label' for Multiprotocol Label Switching Architecture (MPLS) Operation and Maintenance (OAM) Functions. Sections 3 and 6."; } identity extension-label { base mpls-label-special-purpose-value; description "This identity represents the Extension Label."; reference "RFC 7274: Allocating and Retiring Special-Purpose MPLS Labels. Sections 3.1 and 5."; } Liu, et al. Standards Track [Page 10] RFC 8294 Routing Area YANG Types December 2017 /*** Collection of types related to routing ***/ typedef router-id { type yang:dotted-quad; description "A 32-bit number in the dotted-quad format assigned to each router. This number uniquely identifies the router within an Autonomous System."; } /*** Collection of types related to VPNs ***/ typedef route-target { type string { pattern '(0:(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0):(429496729[0-5]|' + '42949672[0-8][0-9]|' + '4294967[01][0-9]{2}|429496[0-6][0-9]{3}|' + '42949[0-5][0-9]{4}|' + '4294[0-8][0-9]{5}|429[0-3][0-9]{6}|' + '42[0-8][0-9]{7}|4[01][0-9]{8}|' + '[1-3][0-9]{9}|[1-9][0-9]{0,8}|0))|' + '(1:((([0-9]|[1-9][0-9]|1[0-9]{2}|2[0-4][0-9]|' + '25[0-5])\.){3}([0-9]|[1-9][0-9]|' + '1[0-9]{2}|2[0-4][0-9]|25[0-5])):(6553[0-5]|' + '655[0-2][0-9]|' + '65[0-4][0-9]{2}|6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0))|' + '(2:(429496729[0-5]|42949672[0-8][0-9]|' + '4294967[01][0-9]{2}|' + '429496[0-6][0-9]{3}|42949[0-5][0-9]{4}|' + '4294[0-8][0-9]{5}|' + '429[0-3][0-9]{6}|42[0-8][0-9]{7}|4[01][0-9]{8}|' + '[1-3][0-9]{9}|[1-9][0-9]{0,8}|0):' + '(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0))|' + '(6(:[a-fA-F0-9]{2}){6})|' + '(([3-57-9a-fA-F]|[1-9a-fA-F][0-9a-fA-F]{1,3}):' + '[0-9a-fA-F]{1,12})'; } Liu, et al. Standards Track [Page 11] RFC 8294 Routing Area YANG Types December 2017 description "A Route Target is an 8-octet BGP extended community initially identifying a set of sites in a BGP VPN (RFC 4364). However, it has since taken on a more general role in BGP route filtering. A Route Target consists of two or three fields: a 2-octet Type field, an administrator field, and, optionally, an assigned number field. According to the data formats for types 0, 1, 2, and 6 as defined in RFC 4360, RFC 5668, and RFC 7432, the encoding pattern is defined as: 0:2-octet-asn:4-octet-number 1:4-octet-ipv4addr:2-octet-number 2:4-octet-asn:2-octet-number 6:6-octet-mac-address Additionally, a generic pattern is defined for future Route Target types: 2-octet-other-hex-number:6-octet-hex-number Some valid examples are 0:100:100, 1:1.1.1.1:100, 2:1234567890:203, and 6:26:00:08:92:78:00."; reference "RFC 4360: BGP Extended Communities Attribute. RFC 4364: BGP/MPLS IP Virtual Private Networks (VPNs). RFC 5668: 4-Octet AS Specific BGP Extended Community. RFC 7432: BGP MPLS-Based Ethernet VPN."; } Liu, et al. Standards Track [Page 12] RFC 8294 Routing Area YANG Types December 2017 typedef ipv6-route-target { type string { pattern '((:|[0-9a-fA-F]{0,4}):)([0-9a-fA-F]{0,4}:){0,5}' + '((([0-9a-fA-F]{0,4}:)?(:|[0-9a-fA-F]{0,4}))|' + '(((25[0-5]|2[0-4][0-9]|1[0-9]{2}|[1-9]?[0-9])\.){3}' + '(25[0-5]|2[0-4][0-9]|1[0-9]{2}|[1-9]?[0-9])))' + ':' + '(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0)'; pattern '((([^:]+:){6}(([^:]+:[^:]+)|(.*\..*)))|' + '((([^:]+:)*[^:]+)?::(([^:]+:)*[^:]+)?))' + ':' + '(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0)'; } description "An IPv6 Route Target is a 20-octet BGP IPv6 Address Specific Extended Community serving the same function as a standard 8-octet Route Target, except that it only allows an IPv6 address as the global administrator. The format is . Two valid examples are 2001:db8::1:6544 and 2001:db8::5eb1:791:6b37:17958."; reference "RFC 5701: IPv6 Address Specific BGP Extended Community Attribute."; } typedef route-target-type { type enumeration { enum import { value 0; description "The Route Target applies to route import."; } enum export { value 1; description "The Route Target applies to route export."; } Liu, et al. Standards Track [Page 13] RFC 8294 Routing Area YANG Types December 2017 enum both { value 2; description "The Route Target applies to both route import and route export."; } } description "Indicates the role a Route Target takes in route filtering."; reference "RFC 4364: BGP/MPLS IP Virtual Private Networks (VPNs)."; } typedef route-distinguisher { type string { pattern '(0:(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0):(429496729[0-5]|' + '42949672[0-8][0-9]|' + '4294967[01][0-9]{2}|429496[0-6][0-9]{3}|' + '42949[0-5][0-9]{4}|' + '4294[0-8][0-9]{5}|429[0-3][0-9]{6}|' + '42[0-8][0-9]{7}|4[01][0-9]{8}|' + '[1-3][0-9]{9}|[1-9][0-9]{0,8}|0))|' + '(1:((([0-9]|[1-9][0-9]|1[0-9]{2}|2[0-4][0-9]|' + '25[0-5])\.){3}([0-9]|[1-9][0-9]|' + '1[0-9]{2}|2[0-4][0-9]|25[0-5])):(6553[0-5]|' + '655[0-2][0-9]|' + '65[0-4][0-9]{2}|6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0))|' + '(2:(429496729[0-5]|42949672[0-8][0-9]|' + '4294967[01][0-9]{2}|' + '429496[0-6][0-9]{3}|42949[0-5][0-9]{4}|' + '4294[0-8][0-9]{5}|' + '429[0-3][0-9]{6}|42[0-8][0-9]{7}|4[01][0-9]{8}|' + '[1-3][0-9]{9}|[1-9][0-9]{0,8}|0):' + '(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0))|' + '(6(:[a-fA-F0-9]{2}){6})|' + '(([3-57-9a-fA-F]|[1-9a-fA-F][0-9a-fA-F]{1,3}):' + '[0-9a-fA-F]{1,12})'; } Liu, et al. Standards Track [Page 14] RFC 8294 Routing Area YANG Types December 2017 description "A Route Distinguisher is an 8-octet value used to distinguish routes from different BGP VPNs (RFC 4364). A Route Distinguisher will have the same format as a Route Target as per RFC 4360 and will consist of two or three fields: a 2-octet Type field, an administrator field, and, optionally, an assigned number field. According to the data formats for types 0, 1, 2, and 6 as defined in RFC 4360, RFC 5668, and RFC 7432, the encoding pattern is defined as: 0:2-octet-asn:4-octet-number 1:4-octet-ipv4addr:2-octet-number 2:4-octet-asn:2-octet-number 6:6-octet-mac-address Additionally, a generic pattern is defined for future route discriminator types: 2-octet-other-hex-number:6-octet-hex-number Some valid examples are 0:100:100, 1:1.1.1.1:100, 2:1234567890:203, and 6:26:00:08:92:78:00."; reference "RFC 4360: BGP Extended Communities Attribute. RFC 4364: BGP/MPLS IP Virtual Private Networks (VPNs). RFC 5668: 4-Octet AS Specific BGP Extended Community. RFC 7432: BGP MPLS-Based Ethernet VPN."; } Liu, et al. Standards Track [Page 15] RFC 8294 Routing Area YANG Types December 2017 typedef route-origin { type string { pattern '(0:(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0):(429496729[0-5]|' + '42949672[0-8][0-9]|' + '4294967[01][0-9]{2}|429496[0-6][0-9]{3}|' + '42949[0-5][0-9]{4}|' + '4294[0-8][0-9]{5}|429[0-3][0-9]{6}|' + '42[0-8][0-9]{7}|4[01][0-9]{8}|' + '[1-3][0-9]{9}|[1-9][0-9]{0,8}|0))|' + '(1:((([0-9]|[1-9][0-9]|1[0-9]{2}|2[0-4][0-9]|' + '25[0-5])\.){3}([0-9]|[1-9][0-9]|' + '1[0-9]{2}|2[0-4][0-9]|25[0-5])):(6553[0-5]|' + '655[0-2][0-9]|' + '65[0-4][0-9]{2}|6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0))|' + '(2:(429496729[0-5]|42949672[0-8][0-9]|' + '4294967[01][0-9]{2}|' + '429496[0-6][0-9]{3}|42949[0-5][0-9]{4}|' + '4294[0-8][0-9]{5}|' + '429[0-3][0-9]{6}|42[0-8][0-9]{7}|4[01][0-9]{8}|' + '[1-3][0-9]{9}|[1-9][0-9]{0,8}|0):' + '(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0))|' + '(6(:[a-fA-F0-9]{2}){6})|' + '(([3-57-9a-fA-F]|[1-9a-fA-F][0-9a-fA-F]{1,3}):' + '[0-9a-fA-F]{1,12})'; } description "A Route Origin is an 8-octet BGP extended community identifying the set of sites where the BGP route originated (RFC 4364). A Route Origin will have the same format as a Route Target as per RFC 4360 and will consist of two or three fields: a 2-octet Type field, an administrator field, and, optionally, an assigned number field. According to the data formats for types 0, 1, 2, and 6 as defined in RFC 4360, RFC 5668, and RFC 7432, the encoding pattern is defined as: 0:2-octet-asn:4-octet-number 1:4-octet-ipv4addr:2-octet-number 2:4-octet-asn:2-octet-number 6:6-octet-mac-address Liu, et al. Standards Track [Page 16] RFC 8294 Routing Area YANG Types December 2017 Additionally, a generic pattern is defined for future Route Origin types: 2-octet-other-hex-number:6-octet-hex-number Some valid examples are 0:100:100, 1:1.1.1.1:100, 2:1234567890:203, and 6:26:00:08:92:78:00."; reference "RFC 4360: BGP Extended Communities Attribute. RFC 4364: BGP/MPLS IP Virtual Private Networks (VPNs). RFC 5668: 4-Octet AS Specific BGP Extended Community. RFC 7432: BGP MPLS-Based Ethernet VPN."; } typedef ipv6-route-origin { type string { pattern '((:|[0-9a-fA-F]{0,4}):)([0-9a-fA-F]{0,4}:){0,5}' + '((([0-9a-fA-F]{0,4}:)?(:|[0-9a-fA-F]{0,4}))|' + '(((25[0-5]|2[0-4][0-9]|1[0-9]{2}|[1-9]?[0-9])\.){3}' + '(25[0-5]|2[0-4][0-9]|1[0-9]{2}|[1-9]?[0-9])))' + ':' + '(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0)'; pattern '((([^:]+:){6}(([^:]+:[^:]+)|(.*\..*)))|' + '((([^:]+:)*[^:]+)?::(([^:]+:)*[^:]+)?))' + ':' + '(6553[0-5]|655[0-2][0-9]|65[0-4][0-9]{2}|' + '6[0-4][0-9]{3}|' + '[1-5][0-9]{4}|[1-9][0-9]{0,3}|0)'; } description "An IPv6 Route Origin is a 20-octet BGP IPv6 Address Specific Extended Community serving the same function as a standard 8-octet route, except that it only allows an IPv6 address as the global administrator. The format is . Two valid examples are 2001:db8::1:6544 and 2001:db8::5eb1:791:6b37:17958."; reference "RFC 5701: IPv6 Address Specific BGP Extended Community Attribute."; } Liu, et al. Standards Track [Page 17] RFC 8294 Routing Area YANG Types December 2017 /*** Collection of types common to multicast ***/ typedef ipv4-multicast-group-address { type inet:ipv4-address { pattern '(2((2[4-9])|(3[0-9]))\.).*'; } description "This type represents an IPv4 multicast group address, which is in the range of 224.0.0.0 to 239.255.255.255."; reference "RFC 1112: Host Extensions for IP Multicasting."; } typedef ipv6-multicast-group-address { type inet:ipv6-address { pattern '(([fF]{2}[0-9a-fA-F]{2}):).*'; } description "This type represents an IPv6 multicast group address, which is in the range of ff00::/8."; reference "RFC 4291: IP Version 6 Addressing Architecture. Section 2.7. RFC 7346: IPv6 Multicast Address Scopes."; } typedef ip-multicast-group-address { type union { type ipv4-multicast-group-address; type ipv6-multicast-group-address; } description "This type represents a version-neutral IP multicast group address. The format of the textual representation implies the IP version."; } Liu, et al. Standards Track [Page 18] RFC 8294 Routing Area YANG Types December 2017 typedef ipv4-multicast-source-address { type union { type enumeration { enum * { description "Any source address."; } } type inet:ipv4-address; } description "Multicast source IPv4 address type."; } typedef ipv6-multicast-source-address { type union { type enumeration { enum * { description "Any source address."; } } type inet:ipv6-address; } description "Multicast source IPv6 address type."; } /*** Collection of types common to protocols ***/ typedef bandwidth-ieee-float32 { type string { pattern '0[xX](0((\.0?)?[pP](\+)?0?|(\.0?))|' + '1(\.([0-9a-fA-F]{0,5}[02468aAcCeE]?)?)?[pP](\+)?(12[0-7]|' + '1[01][0-9]|0?[0-9]?[0-9])?)'; } description "Bandwidth in IEEE 754 floating-point 32-bit binary format: (-1)**(S) * 2**(Exponent-127) * (1 + Fraction), where Exponent uses 8 bits and Fraction uses 23 bits. The units are octets per second. The encoding format is the external hexadecimal-significant character sequences specified in IEEE 754 and ISO/IEC C99. The format is restricted to be normalized, non-negative, and non-fraction: 0x1.hhhhhhp{+}d, 0X1.HHHHHHP{+}D, or 0x0p0, where 'h' and 'H' are hexadecimal digits and 'd' and 'D' are integers in the range of [0..127]. Liu, et al. Standards Track [Page 19] RFC 8294 Routing Area YANG Types December 2017 When six hexadecimal digits are used for 'hhhhhh' or 'HHHHHH', the least significant digit must be an even number. 'x' and 'X' indicate hexadecimal; 'p' and 'P' indicate a power of two. Some examples are 0x0p0, 0x1p10, and 0x1.abcde2p+20."; reference "IEEE Std 754-2008: IEEE Standard for Floating-Point Arithmetic. ISO/IEC C99: Information technology - Programming Languages - C."; } typedef link-access-type { type enumeration { enum broadcast { description "Specify broadcast multi-access network."; } enum non-broadcast-multiaccess { description "Specify Non-Broadcast Multi-Access (NBMA) network."; } enum point-to-multipoint { description "Specify point-to-multipoint network."; } enum point-to-point { description "Specify point-to-point network."; } } description "Link access type."; } typedef timer-multiplier { type uint8; description "The number of timer value intervals that should be interpreted as a failure."; } Liu, et al. Standards Track [Page 20] RFC 8294 Routing Area YANG Types December 2017 typedef timer-value-seconds16 { type union { type uint16 { range "1..65535"; } type enumeration { enum infinity { description "The timer is set to infinity."; } enum not-set { description "The timer is not set."; } } } units "seconds"; description "Timer value type, in seconds (16-bit range)."; } typedef timer-value-seconds32 { type union { type uint32 { range "1..4294967295"; } type enumeration { enum infinity { description "The timer is set to infinity."; } enum not-set { description "The timer is not set."; } } } units "seconds"; description "Timer value type, in seconds (32-bit range)."; } Liu, et al. Standards Track [Page 21] RFC 8294 Routing Area YANG Types December 2017 typedef timer-value-milliseconds { type union { type uint32 { range "1..4294967295"; } type enumeration { enum infinity { description "The timer is set to infinity."; } enum not-set { description "The timer is not set."; } } } units "milliseconds"; description "Timer value type, in milliseconds."; } typedef percentage { type uint8 { range "0..100"; } description "Integer indicating a percentage value."; } typedef timeticks64 { type uint64; description "This type is based on the timeticks type defined in RFC 6991, but with 64-bit width. It represents the time, modulo 2^64, in hundredths of a second between two epochs."; reference "RFC 6991: Common YANG Data Types."; } typedef uint24 { type uint32 { range "0..16777215"; } description "24-bit unsigned integer."; } Liu, et al. Standards Track [Page 22] RFC 8294 Routing Area YANG Types December 2017 /*** Collection of types related to MPLS/GMPLS ***/ typedef generalized-label { type binary; description "Generalized Label. Nodes sending and receiving the Generalized Label are aware of the link-specific label context and type."; reference "RFC 3471: Generalized Multi-Protocol Label Switching (GMPLS) Signaling Functional Description. Section 3.2."; } typedef mpls-label-special-purpose { type identityref { base mpls-label-special-purpose-value; } description "This type represents the special-purpose MPLS label values."; reference "RFC 3032: MPLS Label Stack Encoding. RFC 7274: Allocating and Retiring Special-Purpose MPLS Labels."; } typedef mpls-label-general-use { type uint32 { range "16..1048575"; } description "The 20-bit label value in an MPLS label stack as specified in RFC 3032. This label value does not include the encodings of Traffic Class and TTL (Time to Live). The label range specified by this type is for general use, with special-purpose MPLS label values excluded."; reference "RFC 3032: MPLS Label Stack Encoding."; } Liu, et al. Standards Track [Page 23] RFC 8294 Routing Area YANG Types December 2017 typedef mpls-label { type union { type mpls-label-special-purpose; type mpls-label-general-use; } description "The 20-bit label value in an MPLS label stack as specified in RFC 3032. This label value does not include the encodings of Traffic Class and TTL."; reference "RFC 3032: MPLS Label Stack Encoding."; } /*** Groupings **/ grouping mpls-label-stack { description "This grouping specifies an MPLS label stack. The label stack is encoded as a list of label stack entries. The list key is an identifier that indicates the relative ordering of each entry, with the lowest-value identifier corresponding to the top of the label stack."; container mpls-label-stack { description "Container for a list of MPLS label stack entries."; list entry { key "id"; description "List of MPLS label stack entries."; leaf id { type uint8; description "Identifies the entry in a sequence of MPLS label stack entries. An entry with a smaller identifier value precedes an entry with a larger identifier value in the label stack. The value of this ID has no semantic meaning other than relative ordering and referencing the entry."; } leaf label { type rt-types:mpls-label; description "Label value."; } Liu, et al. Standards Track [Page 24] RFC 8294 Routing Area YANG Types December 2017 leaf ttl { type uint8; description "Time to Live (TTL)."; reference "RFC 3032: MPLS Label Stack Encoding."; } leaf traffic-class { type uint8 { range "0..7"; } description "Traffic Class (TC)."; reference "RFC 5462: Multiprotocol Label Switching (MPLS) Label Stack Entry: 'EXP' Field Renamed to 'Traffic Class' Field."; } } } } Liu, et al. Standards Track [Page 25] RFC 8294 Routing Area YANG Types December 2017 grouping vpn-route-targets { description "A grouping that specifies Route Target import-export rules used in BGP-enabled VPNs."; reference "RFC 4364: BGP/MPLS IP Virtual Private Networks (VPNs). RFC 4664: Framework for Layer 2 Virtual Private Networks (L2VPNs)."; list vpn-target { key "route-target"; description "List of Route Targets."; leaf route-target { type rt-types:route-target; description "Route Target value."; } leaf route-target-type { type rt-types:route-target-type; mandatory true; description "Import/export type of the Route Target."; } } } } Liu, et al. Standards Track [Page 26] RFC 8294 Routing Area YANG Types December 2017 4. IANA Routing Types YANG Module file "iana-routing-types@2017-12-04.yang" module iana-routing-types { namespace "urn:ietf:params:xml:ns:yang:iana-routing-types"; prefix iana-rt-types; organization "IANA"; contact "Internet Assigned Numbers Authority Postal: ICANN 12025 Waterfront Drive, Suite 300 Los Angeles, CA 90094-2536 United States of America Tel: +1 310 301 5800 "; description "This module contains a collection of YANG data types considered defined by IANA and used for routing protocols. Copyright (c) 2017 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info). This version of this YANG module is part of RFC 8294; see the RFC itself for full legal notices."; revision 2017-12-04 { description "Initial revision."; reference "RFC 8294: Common YANG Data Types for the Routing Area. Section 4."; } Liu, et al. Standards Track [Page 27] RFC 8294 Routing Area YANG Types December 2017 /*** Collection of IANA types related to routing ***/ /*** IANA Address Family enumeration ***/ typedef address-family { type enumeration { enum ipv4 { value 1; description "IPv4 Address Family."; } enum ipv6 { value 2; description "IPv6 Address Family."; } enum nsap { value 3; description "OSI Network Service Access Point (NSAP) Address Family."; } enum hdlc { value 4; description "High-Level Data Link Control (HDLC) Address Family."; } enum bbn1822 { value 5; description "Bolt, Beranek, and Newman Report 1822 (BBN 1822) Address Family."; } enum ieee802 { value 6; description "IEEE 802 Committee Address Family (aka Media Access Control (MAC) address)."; } enum e163 { value 7; description "ITU-T E.163 Address Family."; } Liu, et al. Standards Track [Page 28] RFC 8294 Routing Area YANG Types December 2017 enum e164 { value 8; description "ITU-T E.164 (Switched Multimegabit Data Service (SMDS), Frame Relay, ATM) Address Family."; } enum f69 { value 9; description "ITU-T F.69 (Telex) Address Family."; } enum x121 { value 10; description "ITU-T X.121 (X.25, Frame Relay) Address Family."; } enum ipx { value 11; description "Novell Internetwork Packet Exchange (IPX) Address Family."; } enum appletalk { value 12; description "Apple AppleTalk Address Family."; } enum decnet-iv { value 13; description "Digital Equipment DECnet Phase IV Address Family."; } enum vines { value 14; description "Banyan Vines Address Family."; } Liu, et al. Standards Track [Page 29] RFC 8294 Routing Area YANG Types December 2017 enum e164-nsap { value 15; description "ITU-T E.164 with NSAP sub-address Address Family."; } enum dns { value 16; description "Domain Name System (DNS) Address Family."; } enum distinguished-name { value 17; description "Distinguished Name Address Family."; } enum as-num { value 18; description "Autonomous System (AS) Number Address Family."; } enum xtp-v4 { value 19; description "Xpress Transport Protocol (XTP) over IPv4 Address Family."; } enum xtp-v6 { value 20; description "XTP over IPv6 Address Family."; } enum xtp-native { value 21; description "XTP native mode Address Family."; } enum fc-port { value 22; description "Fibre Channel (FC) World-Wide Port Name Address Family."; } Liu, et al. Standards Track [Page 30] RFC 8294 Routing Area YANG Types December 2017 enum fc-node { value 23; description "FC World-Wide Node Name Address Family."; } enum gwid { value 24; description "ATM Gateway Identifier (GWID) Number Address Family."; } enum l2vpn { value 25; description "Layer 2 VPN (L2VPN) Address Family."; } enum mpls-tp-section-eid { value 26; description "MPLS Transport Profile (MPLS-TP) Section Endpoint Identifier Address Family."; } enum mpls-tp-lsp-eid { value 27; description "MPLS-TP Label Switched Path (LSP) Endpoint Identifier Address Family."; } enum mpls-tp-pwe-eid { value 28; description "MPLS-TP Pseudowire Endpoint Identifier Address Family."; } enum mt-v4 { value 29; description "Multi-Topology IPv4 Address Family."; } Liu, et al. Standards Track [Page 31] RFC 8294 Routing Area YANG Types December 2017 enum mt-v6 { value 30; description "Multi-Topology IPv6 Address Family."; } enum eigrp-common-sf { value 16384; description "Enhanced Interior Gateway Routing Protocol (EIGRP) Common Service Family Address Family."; } enum eigrp-v4-sf { value 16385; description "EIGRP IPv4 Service Family Address Family."; } enum eigrp-v6-sf { value 16386; description "EIGRP IPv6 Service Family Address Family."; } enum lcaf { value 16387; description "Locator/ID Separation Protocol (LISP) Canonical Address Format (LCAF) Address Family."; } enum bgp-ls { value 16388; description "Border Gateway Protocol - Link State (BGP-LS) Address Family."; } enum mac-48 { value 16389; description "IEEE 48-bit MAC Address Family."; } Liu, et al. Standards Track [Page 32] RFC 8294 Routing Area YANG Types December 2017 enum mac-64 { value 16390; description "IEEE 64-bit MAC Address Family."; } enum trill-oui { value 16391; description "Transparent Interconnection of Lots of Links (TRILL) IEEE Organizationally Unique Identifier (OUI) Address Family."; } enum trill-mac-24 { value 16392; description "TRILL final 3 octets of 48-bit MAC Address Family."; } enum trill-mac-40 { value 16393; description "TRILL final 5 octets of 64-bit MAC Address Family."; } enum ipv6-64 { value 16394; description "First 8 octets (64 bits) of IPv6 address Address Family."; } enum trill-rbridge-port-id { value 16395; description "TRILL Routing Bridge (RBridge) Port ID Address Family."; } enum trill-nickname { value 16396; description "TRILL Nickname Address Family."; } } Liu, et al. Standards Track [Page 33] RFC 8294 Routing Area YANG Types December 2017 description "Enumeration containing all the IANA-defined Address Families."; } /*** Subsequent Address Family Identifiers (SAFIs) ***/ /*** for multiprotocol BGP enumeration ***/ typedef bgp-safi { type enumeration { enum unicast-safi { value 1; description "Unicast SAFI."; } enum multicast-safi { value 2; description "Multicast SAFI."; } enum labeled-unicast-safi { value 4; description "Labeled Unicast SAFI."; } enum multicast-vpn-safi { value 5; description "Multicast VPN SAFI."; } enum pseudowire-safi { value 6; description "Multi-segment Pseudowire VPN SAFI."; } enum tunnel-encap-safi { value 7; description "Tunnel Encap SAFI."; } Liu, et al. Standards Track [Page 34] RFC 8294 Routing Area YANG Types December 2017 enum mcast-vpls-safi { value 8; description "Multicast Virtual Private LAN Service (VPLS) SAFI."; } enum tunnel-safi { value 64; description "Tunnel SAFI."; } enum vpls-safi { value 65; description "VPLS SAFI."; } enum mdt-safi { value 66; description "Multicast Distribution Tree (MDT) SAFI."; } enum v4-over-v6-safi { value 67; description "IPv4 over IPv6 SAFI."; } enum v6-over-v4-safi { value 68; description "IPv6 over IPv4 SAFI."; } enum l1-vpn-auto-discovery-safi { value 69; description "Layer 1 VPN Auto-Discovery SAFI."; } enum evpn-safi { value 70; description "Ethernet VPN (EVPN) SAFI."; } Liu, et al. Standards Track [Page 35] RFC 8294 Routing Area YANG Types December 2017 enum bgp-ls-safi { value 71; description "BGP-LS SAFI."; } enum bgp-ls-vpn-safi { value 72; description "BGP-LS VPN SAFI."; } enum sr-te-safi { value 73; description "Segment Routing - Traffic Engineering (SR-TE) SAFI."; } enum labeled-vpn-safi { value 128; description "MPLS Labeled VPN SAFI."; } enum multicast-mpls-vpn-safi { value 129; description "Multicast for BGP/MPLS IP VPN SAFI."; } enum route-target-safi { value 132; description "Route Target SAFI."; } enum ipv4-flow-spec-safi { value 133; description "IPv4 Flow Specification SAFI."; } enum vpnv4-flow-spec-safi { value 134; description "IPv4 VPN Flow Specification SAFI."; } Liu, et al. Standards Track [Page 36] RFC 8294 Routing Area YANG Types December 2017 enum vpn-auto-discovery-safi { value 140; description "VPN Auto-Discovery SAFI."; } } description "Enumeration for BGP SAFI."; reference "RFC 4760: Multiprotocol Extensions for BGP-4."; } } 5. IANA Considerations This document registers the following namespace URIs in the "IETF XML Registry" [RFC3688]: URI: urn:ietf:params:xml:ns:yang:ietf-routing-types Registrant Contact: The IESG. XML: N/A; the requested URI is an XML namespace. URI: urn:ietf:params:xml:ns:yang:iana-routing-types Registrant Contact: IANA. XML: N/A; the requested URI is an XML namespace. This document registers the following YANG modules in the "YANG Module Names" registry [RFC6020]: Name: ietf-routing-types Namespace: urn:ietf:params:xml:ns:yang:ietf-routing-types Prefix: rt-types Reference: RFC 8294 Name: iana-routing-types Namespace: urn:ietf:params:xml:ns:yang:iana-routing-types Prefix: iana-rt-types Reference: RFC 8294 Liu, et al. Standards Track [Page 37] RFC 8294 Routing Area YANG Types December 2017 5.1. IANA-Maintained iana-routing-types Module This document defines the initial version of the IANA-maintained iana-routing-types YANG module (Section 4). The iana-routing-types YANG module is intended to reflect the "Address Family Numbers" registry [IANA-ADDRESS-FAMILY-REGISTRY] and the "Subsequent Address Family Identifiers (SAFI) Parameters" registry [IANA-SAFI-REGISTRY]. IANA has added this note to the "iana-routing-types YANG Module" registry: Address Families and Subsequent Address Families must not be directly added to the iana-routing-types YANG module. They must instead be respectively added to the "Address Family Numbers" and "Subsequent Address Family Identifiers (SAFI) Parameters" registries. When an Address Family or Subsequent Address Family is respectively added to the "Address Family Numbers" registry or the "Subsequent Address Family Identifiers (SAFI) Parameters" registry, a new "enum" statement must be added to the iana-routing-types YANG module. The name of the "enum" is the same as the corresponding Address Family or SAFI, except that it will be a valid YANG identifier in all lowercase and with hyphens separating individual words in compound identifiers. The following "enum" statement, and substatements thereof, should be defined: "enum": Contains the YANG enum identifier for the "address-family" (for Address Families) or "bgp-safi" (for Subsequent Address Families). This may be the same as the "address-family" or "bgp-safi", or it may be a shorter version to facilitate YANG identifier usage. "value": Contains the IANA-assigned value corresponding to the "address-family" (for Address Families) or "bgp-safi" (for Subsequent Address Families). "status": Include only if a registration has been deprecated (use the value "deprecated") or obsoleted (use the value "obsolete"). Liu, et al. Standards Track [Page 38] RFC 8294 Routing Area YANG Types December 2017 "description": Replicate the description from the registry, if any. Insert line breaks as needed so that the line does not exceed 72 characters. "reference": Replicate the reference from the registry, if any, and add the title of the document. Unassigned or reserved values are not present in these modules. When the iana-routing-types YANG module is updated, a new "revision" statement must be added in front of the existing revision statements. IANA has added this new note to the "Address Family Numbers" and "Subsequent Address Family Identifiers (SAFI) Parameters" registries: When this registry is modified, the YANG module iana-routing-types must be updated as defined in RFC 8294. 6. Security Considerations This document defines common routing type definitions (i.e., typedef statements) using the YANG data modeling language. The definitions themselves have no security or privacy impact on the Internet, but the usage of these definitions in concrete YANG modules might have. The security considerations spelled out in the YANG 1.1 specification [RFC7950] apply for this document as well. 7. References 7.1. Normative References [RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, January 2004, . [RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, October 2010, . [RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, July 2013, . [RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, August 2016, . Liu, et al. Standards Track [Page 39] RFC 8294 Routing Area YANG Types December 2017 [IANA-ADDRESS-FAMILY-REGISTRY] "IANA Address Family Numbers Registry", . [IANA-SAFI-REGISTRY] "IANA Subsequent Address Family Identifiers (SAFI) Parameters Registry", . 7.2. Informative References [IEEE754] IEEE, "IEEE Standard for Floating-Point Arithmetic", IEEE 754-2008, DOI 10.1109/IEEESTD.2008.4610935. [BGP-Model] Shaikh, A., Ed., Shakir, R., Ed., Patel, K., Ed., Hares, S., Ed., D'Souza, K., Bansal, D., Clemm, A., Zhdankin, A., Jethanandani, M., and X. Liu, "BGP Model for Service Provider Networks", Work in Progress, draft-ietf-idr-bgp-model-02, July 2016. [OSPF-YANG] Yeung, D., Qu, Y., Zhang, J., Chen, I., and A. Lindem, "Yang Data Model for OSPF Protocol", Work in Progress, draft-ietf-ospf-yang-09, October 2017. [PIM-YANG] Liu, X., McAllister, P., Peter, A., Sivakumar, M., Liu, Y., and F. Hu, "A YANG data model for Protocol-Independent Multicast (PIM)", Work in Progress, draft-ietf-pim-yang-12, December 2017. [TE-YANG] Saad, T., Ed., Gandhi, R., Liu, X., Beeram, V., Shah, H., and I. Bryskin, "A YANG Data Model for Traffic Engineering Tunnels and Interfaces", Work in Progress, draft-ietf-teas-yang-te-09, October 2017. [L2VPN-YANG] Shah, H., Ed., Brissette, P., Ed., Chen, I., Ed., Hussain, I., Ed., Wen, B., Ed., and K. Tiruveedhula, Ed., "YANG Data Model for MPLS-based L2VPN", Work in Progress, draft-ietf-bess-l2vpn-yang-07, September 2017. [MPLS-Base-YANG] Saad, T., Raza, K., Gandhi, R., Liu, X., Beeram, V., Shah, H., Bryskin, I., Chen, X., Jones, R., and B. Wen, "A YANG Data Model for MPLS Base", Work in Progress, draft-ietf-mpls-base-yang-05, July 2017. Liu, et al. Standards Track [Page 40] RFC 8294 Routing Area YANG Types December 2017 [RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack Encoding", RFC 3032, DOI 10.17487/RFC3032, January 2001, . [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001, . [RFC3471] Berger, L., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Functional Description", RFC 3471, DOI 10.17487/RFC3471, January 2003, . [RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February 2006, . [RFC4664] Andersson, L., Ed., and E. Rosen, Ed., "Framework for Layer 2 Virtual Private Networks (L2VPNs)", RFC 4664, DOI 10.17487/RFC4664, September 2006, . [RFC5701] Rekhter, Y., "IPv6 Address Specific BGP Extended Community Attribute", RFC 5701, DOI 10.17487/RFC5701, November 2009, . [RFC5880] Katz, D. and D. Ward, "Bidirectional Forwarding Detection (BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010, . [RFC7274] Kompella, K., Andersson, L., and A. Farrel, "Allocating and Retiring Special-Purpose MPLS Labels", RFC 7274, DOI 10.17487/RFC7274, June 2014, . [RFC7432] Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A., Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February 2015, . Liu, et al. Standards Track [Page 41] RFC 8294 Routing Area YANG Types December 2017 Acknowledgements The Routing Area YANG Architecture design team members included Acee Lindem, Anees Shaikh, Christian Hopps, Dean Bogdanovic, Ebben Aries, Lou Berger, Qin Wu, Rob Shakir, Xufeng Liu, and Yingzhen Qu. Thanks to Martin Bjorklund, Tom Petch, Stewart Bryant, and Radek Krejci for comments on the model and document text. Thanks to Jeff Haas and Robert Raszuk for suggestions for additional common routing types. Liu, et al. Standards Track [Page 42] RFC 8294 Routing Area YANG Types December 2017 Authors' Addresses Xufeng Liu Jabil 8281 Greensboro Drive, Suite 200 McLean, VA 22102 United States of America Email: Xufeng_Liu@jabil.com Yingzhen Qu Futurewei Technologies, Inc. 2330 Central Expressway Santa Clara, CA 95050 United States of America Email: yingzhen.qu@huawei.com Acee Lindem Cisco Systems 301 Midenhall Way Cary, NC 27513 United States of America Email: acee@cisco.com Christian Hopps Deutsche Telekom Email: chopps@chopps.org Lou Berger LabN Consulting, L.L.C. Email: lberger@labn.net Liu, et al. Standards Track [Page 43]