Internet Engineering Task Force (IETF) Y. Cui
Request for Comments: 7596 Tsinghua University
Category: Standards Track Q. Sun
ISSN: 2070-1721 China Telecom
M. Boucadair
France Telecom
T. Tsou
Huawei Technologies
Y. Lee
Comcast
I. Farrer
Deutsche Telekom AG
July 2015
Lightweight 4over6: An Extension to the Dual-Stack Lite Architecture
Abstract
Dual-Stack Lite (DS-Lite) (RFC 6333) describes an architecture for
transporting IPv4 packets over an IPv6 network. This document
specifies an extension to DS-Lite called "Lightweight 4over6", which
moves the Network Address and Port Translation (NAPT) function from
the centralized DS-Lite tunnel concentrator to the tunnel client
located in the Customer Premises Equipment (CPE). This removes the
requirement for a Carrier Grade NAT function in the tunnel
concentrator and reduces the amount of centralized state that must be
held to a per-subscriber level. In order to delegate the NAPT
function and make IPv4 address sharing possible, port-restricted IPv4
addresses are allocated to the CPEs.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc7596.
Cui, et al. Standards Track [Page 1]
RFC 7596 Lightweight 4over6 July 2015
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................3
2. Conventions .....................................................4
3. Terminology .....................................................5
4. Lightweight 4over6 Architecture .................................6
5. Lightweight B4 Behavior .........................................7
5.1. Lightweight B4 Provisioning with DHCPv6 ....................7
5.2. Lightweight B4 Data-Plane Behavior ........................10
5.2.1. Fragmentation Behavior .............................11
6. Lightweight AFTR Behavior ......................................12
6.1. Binding Table Maintenance .................................12
6.2. lwAFTR Data-Plane Behavior ................................13
7. Additional IPv4 Address and Port-Set Provisioning Mechanisms ...14
8. ICMP Processing ................................................14
8.1. ICMPv4 Processing by the lwAFTR ...........................15
8.2. ICMPv4 Processing by the lwB4 .............................15
9. Security Considerations ........................................15
10. References ....................................................16
10.1. Normative References .....................................16
10.2. Informative References ...................................17
Acknowledgements ..................................................19
Contributors ......................................................19
Authors' Addresses ................................................21
Cui, et al. Standards Track [Page 2]
RFC 7596 Lightweight 4over6 July 2015
1. Introduction
Dual-Stack Lite (DS-Lite) [RFC6333] defines a model for providing
IPv4 access over an IPv6 network using two well-known technologies:
IP in IP [RFC2473] and Network Address Translation (NAT). The
DS-Lite architecture defines two major functional elements as
follows:
Basic Bridging BroadBand (B4) element: A function implemented on a
dual-stack-capable node (either a directly connected device or a
CPE) that creates an IPv4-in-IPv6 tunnel to an AFTR.
Address Family Transition Router (AFTR) element: The combination of
an IPv4-in-IPv6 tunnel endpoint and an IPv4-IPv4 NAT implemented
on the same node.
As the AFTR performs the centralized NAT44 function, it dynamically
assigns public IPv4 addresses and ports to a requesting host's
traffic (as described in [RFC3022]). To achieve this, the AFTR must
dynamically maintain per-flow state in the form of active NAPT
sessions. For service providers with a large number of B4 clients,
the size and associated costs for scaling the AFTR can quickly become
prohibitive. Maintaining per-flow state can also place a large NAPT
logging overhead on the service provider in countries where logging
is a legal requirement.
This document describes a mechanism called "Lightweight 4over6"
(lw4o6), which provides a solution for these problems. By relocating
the NAPT functionality from the centralized AFTR to the distributed
B4s, a number of benefits can be realized:
o NAPT44 functionality is already widely supported and used in
today's CPE devices. lw4o6 uses this to provide private<->public
NAPT44, meaning that the service provider does not need a
centralized NAT44 function.
o The amount of state that must be maintained centrally in the AFTR
can be reduced from per-flow to per-subscriber. This reduces
the amount of resources (memory and processing power) necessary in
the AFTR.
o The reduction of maintained state results in a greatly reduced
logging overhead on the service provider.
Operators' IPv6 and IPv4 addressing architectures remain independent
of each other. Therefore, flexible IPv4/IPv6 addressing schemes can
be deployed.
Cui, et al. Standards Track [Page 3]
RFC 7596 Lightweight 4over6 July 2015
Lightweight 4over6 is a solution designed specifically for complete
independence between IPv6 subnet prefixes and IPv4 addresses with or
without IPv4 address sharing. This is accomplished by maintaining
state for each softwire (per-subscriber state) in the central lwAFTR
and a hub-and-spoke forwarding architecture. "Mapping of Address and
Port with Encapsulation (MAP-E)" [RFC7597] also offers these
capabilities or, alternatively, allows for a reduction of the amount
of centralized state using rules to express IPv4/IPv6 address
mappings. This introduces an algorithmic relationship between the
IPv6 subnet and IPv4 address. This relationship also allows the
option of direct, meshed connectivity between users.
The tunneling mechanism remains the same for DS-Lite and Lightweight
4over6. This document describes the changes to DS-Lite that are
necessary to implement Lightweight 4over6. These changes mainly
concern the configuration parameters and provisioning method
necessary for the functional elements.
One of the features of Lightweight 4over6 is to keep per-subscriber
state in the service provider's network. This technique is
categorized as a "binding approach" [Unified-v4-in-v6] that defines a
unified IPv4-in-IPv6 softwire CPE.
This document extends the mechanism defined in [RFC7040] by allowing
address sharing. The solution in this document is also a variant of
Address plus Port (A+P) called "Binding Table Mode" (see Section 4.4
of [RFC6346]).
This document focuses on architectural considerations, particularly
on the expected behavior of the involved functional elements and
their interfaces. Deployment-specific issues such as redundancy and
provisioning policy are out of scope for this document.
2. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Cui, et al. Standards Track [Page 4]
RFC 7596 Lightweight 4over6 July 2015
3. Terminology
This document defines the following terms:
Lightweight 4over6 (lw4o6): An IPv4-over-IPv6 hub-and-spoke
mechanism that extends DS-Lite by
moving the IPv4 translation (NAPT44)
function from the AFTR to the B4.
Lightweight B4 (lwB4): A B4 element [RFC6333] that supports
Lightweight 4over6 extensions. An lwB4
is a function implemented on a
dual-stack-capable node -- either a
directly connected device or a CPE --
that supports port-restricted IPv4
address allocation, implements NAPT44
functionality, and creates a tunnel to
an lwAFTR.
Lightweight AFTR (lwAFTR): An AFTR element [RFC6333] that supports
the Lightweight 4over6 extension. An
lwAFTR is an IPv4-in-IPv6 tunnel
endpoint that maintains per-subscriber
address binding only and does not
perform a NAPT44 function.
Restricted port set: A non-overlapping range of allowed
external ports allocated to the lwB4 to
use for NAPT44. Source ports of IPv4
packets sent by the B4 must belong to
the assigned port set. The port set is
used for all port-aware IP protocols
(TCP, UDP, the Stream Control
Transmission Protocol (SCTP), etc.).
Port-restricted IPv4 address: A public IPv4 address with a restricted
port set. In Lightweight 4over6,
multiple B4s may share the same IPv4
address; however, their port sets must
be non-overlapping.
Throughout the remainder of this document, the terms "B4" and "AFTR"
should be understood to refer specifically to a DS-Lite
implementation. The terms "lwB4" and "lwAFTR" refer to a Lightweight
4over6 implementation.
Cui, et al. Standards Track [Page 5]
RFC 7596 Lightweight 4over6 July 2015
4. Lightweight 4over6 Architecture
The Lightweight 4over6 architecture is functionally similar to
DS-Lite. lwB4s and an lwAFTR are connected through an IPv6-enabled
network. Both approaches use an IPv4-in-IPv6 encapsulation scheme to
deliver IPv4 connectivity. The following figure shows the data plane
with the main functional change between DS-Lite and lw4o6:
+--------+ +---------+ IPv4-in-IPv6 +---------+ +-------------+
|IPv4 LAN|---| B4 |================|AFTR/NAPT|---|IPv4 Internet|
+--------+ +---------+ +---------+ +-------------+
DS-Lite NAPT model: all state in the AFTR
+--------+ +---------+ IPv4-in-IPv6 +------+ +-------------+
|IPv4 LAN|---|lwB4/NAPT|================|lwAFTR|---|IPv4 Internet|
+--------+ +---------+ +------+ +-------------+
lw4o6 NAPT model:
subscriber state in the lwAFTR, NAPT state in the lwB4
Figure 1: Comparison of DS-Lite and Lightweight 4over6 Data Plane
There are three main components in the Lightweight 4over6
architecture:
o The lwB4, which performs the NAPT function and IPv4/IPv6
encapsulation/decapsulation.
o The lwAFTR, which performs the IPv4/IPv6 encapsulation/
decapsulation.
o The provisioning system, which tells the lwB4 which IPv4 address
and port set to use.
The lwB4 differs from a regular B4 in that it now performs the NAPT
functionality. This means that it needs to be provisioned with the
public IPv4 address and port set it is allowed to use. This
information is provided through a provisioning mechanism such as
DHCP, the Port Control Protocol (PCP) [RFC6887], or the Broadband
Forum's TR-69 specification [TR069].
The lwAFTR needs to know the binding between the IPv6 address of
each subscriber as well as the IPv4 address and port set allocated to
each subscriber. This information is used to perform ingress
filtering upstream and encapsulation downstream. Note that this is
per-subscriber state, as opposed to per-flow state in the regular
AFTR case.
Cui, et al. Standards Track [Page 6]
RFC 7596 Lightweight 4over6 July 2015
The consequence of this architecture is that the information
maintained by the provisioning mechanism and the one maintained by
the lwAFTR MUST be synchronized (see Figure 2). The precise
mechanism whereby this synchronization occurs is out of scope for
this document.
The solution specified in this document allows the assignment of
either a full or a shared IPv4 address to requesting CPEs. [RFC7040]
provides a mechanism for assigning a full IPv4 address only.
+------------+
/-------|Provisioning|<-----\
| +------------+ |
| |
V V
+--------+ +---------+ IPv4/IPv6 +------+ +-------------+
|IPv4 LAN|---|lwB4/NAPT|==================|lwAFTR|----|IPv4 Internet|
+--------+ +---------+ +------+ +-------------+
Figure 2: Lightweight 4over6 Provisioning Synchronization
5. Lightweight B4 Behavior
5.1. Lightweight B4 Provisioning with DHCPv6
With DS-Lite, the B4 element only needs to be configured with a
single DS-Lite-specific parameter so that it can set up the softwire
(the IPv6 address of the AFTR). Its IPv4 address can be taken from
the well-known range 192.0.0.0/29.
In lw4o6, a number of lw4o6-specific configuration parameters must be
provisioned to the lwB4. These are:
o IPv6 address for the lwAFTR
o IPv4 external (public) address for NAPT44
o Restricted port set to use for NAPT44
o IPv6 binding prefix
The lwB4 MUST implement DHCPv6-based configuration using
OPTION_S46_CONT_LW as described in Section 5.3 of [RFC7598]. This
means that the lifetime of the softwire and the derived configuration
information (e.g., IPv4 shared address, IPv4 address) are bound to
the lifetime of the DHCPv6 lease. If stateful IPv4 configuration or
additional IPv4 configuration information is required, DHCP 4o6
[RFC7341] MUST be used.
Cui, et al. Standards Track [Page 7]
RFC 7596 Lightweight 4over6 July 2015
Although it would be possible to extend lw4o6 to have more than one
active lw4o6 tunnel configured simultaneously, this document is only
concerned with the use of a single tunnel.
The IPv6 binding prefix field is provisioned so that the Customer
Edge (CE) can identify the correct prefix to use as the tunnel
source. On receipt of the necessary configuration parameters listed
above, the lwB4 performs a longest-prefix match between the IPv6
binding prefix and its currently active IPv6 prefixes. The result
forms the subnet to be used for sourcing the lw4o6 tunnel. The full
/128 address is then constructed in the same manner as [RFC7597].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Operator Assigned Prefix |
. (64 bits) .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Zero Padding | IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv4 Addr cont. | PSID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: Construction of the lw4o6 /128 Prefix
Operator Assigned Prefix:
IPv6 prefix allocated to the client. If the prefix
length is less than 64, it is right-padded with zeros
to 64 bits.
Padding: Padding (all zeros).
IPv4 Address: Public IPv4 address allocated to the client.
PSID: Port Set ID. Allocated to the client; left-padded with
zeros to 16 bits. If no PSID is provisioned, all
zeros.
In the event that the lwB4's IPv6 encapsulation source address is
changed for any reason (such as the DHCPv6 lease expiring), the
lwB4's dynamic provisioning process MUST be re-initiated. When the
lwB4's public IPv4 address or Port Set ID is changed for any reason,
the lwB4 MUST flush its NAPT table.
Cui, et al. Standards Track [Page 8]
RFC 7596 Lightweight 4over6 July 2015
An lwB4 MUST support dynamic port-restricted IPv4 address
provisioning. The port-set algorithm for provisioning this is
described in Section 5.1 of [RFC7597]. For lw4o6, the number of
a-bits SHOULD be 0, thus allocating a single contiguous port set to
each lwB4.
Provisioning of the lwB4 using DHCPv6 as described here allocates a
single PSID to the client. In the event that the client is
concurrently using all of the provisioned L4 ports, it may be unable
to initiate any additional outbound connections. DHCPv6-based
provisioning does not provide a mechanism for the client to request
more L4 port numbers. Other provisioning mechanisms (e.g., PCP-based
provisioning [PCP-PORT_SET]) provide this function. Issues relevant
to IP address sharing are discussed in more detail in [RFC6269].
Unless an lwB4 is being allocated a full IPv4 address, it is
RECOMMENDED that PSIDs containing the system ports (0-1023) not be
allocated to lwB4s. The reserved ports are more likely to be
reserved by middleware, and therefore we recommend that they not be
issued to clients other than as a deliberate assignment.
Section 5.2.2 of [RFC6269] provides analysis of allocating system
ports to clients with IPv4 address sharing.
In the event that the lwB4 receives an ICMPv6 error message (Type 1,
Code 5) originating from the lwAFTR, the lwB4 interprets this to mean
that no matching entry in the lwAFTR's binding table has been found,
so the IPv4 payload is not being forwarded by the lwAFTR. The lwB4
MAY then re-initiate the dynamic port-restricted provisioning
process. The lwB4's re-initiation policy SHOULD be configurable.
On receipt of such an ICMP error message, the lwB4 MUST validate the
source address to be the same as the lwAFTR address that is
configured. In the event that these addresses do not match, the lwB4
MUST discard the ICMP error message.
In order to prevent forged ICMP messages (using the spoofed lwAFTR
address as the source) from being sent to lwB4s, the operator can
implement network ingress filtering as described in [RFC2827].
The DNS considerations described in Sections 5.5 and 6.4 of [RFC6333]
apply to Lightweight 4over6; lw4o6 implementations MUST comply with
all requirements stated there.
Cui, et al. Standards Track [Page 9]
RFC 7596 Lightweight 4over6 July 2015
5.2. Lightweight B4 Data-Plane Behavior
Several sections of [RFC6333] provide background information on the
B4's data-plane functionality and MUST be implemented by the lwB4, as
they are common to both solutions. The relevant sections are:
5.2 Encapsulation Covering encapsulation and
decapsulation of tunneled traffic
5.3 Fragmentation and Reassembly Covering MTU and fragmentation
considerations (referencing
[RFC2473])
7.1 Tunneling Covering tunneling and Traffic
Class mapping between IPv4 and IPv6
(referencing [RFC2473]). Also see
[RFC2983]
The lwB4 element performs IPv4 address translation (NAPT44) as well
as encapsulation and decapsulation. It runs standard NAPT44
[RFC3022] using the allocated port-restricted address as its external
IPv4 address and range of source ports.
The working flow of the lwB4 is illustrated in Figure 4.
+-------------+
| lwB4 |
+--------+ IPv4 |------+------| IPv4-in-IPv6 +----------+
|IPv4 LAN|------->| |Encap.|-------------->|Configured|
| |<-------| NAPT | or |<--------------| lwAFTR |
+--------+ | |Decap.| +----------+
+------+------+
Figure 4: Working Flow of the lwB4
Hosts connected to the customer's network behind the lwB4 source IPv4
packets with an [RFC1918] address. When the lwB4 receives such an
IPv4 packet, it performs a NAPT44 function on the source address and
port by using the public IPv4 address and a port number from the
allocated port set. Then, it encapsulates the packet with an IPv6
header. The destination IPv6 address is the lwAFTR's IPv6 address,
and the source IPv6 address is the lwB4's IPv6 tunnel endpoint
address. Finally, the lwB4 forwards the encapsulated packet to the
configured lwAFTR.
Cui, et al. Standards Track [Page 10]
RFC 7596 Lightweight 4over6 July 2015
When the lwB4 receives an IPv4-in-IPv6 packet from the lwAFTR, it
decapsulates the IPv4 packet from the IPv6 packet. Then, it performs
NAPT44 translation on the destination address and port, based on the
available information in its local NAPT44 table.
If the IPv6 source address does not match the configured lwAFTR
address, then the packet MUST be discarded. If the decapsulated IPv4
packet does not match the lwB4's configuration (i.e., invalid
destination IPv4 address or port), then the packet MUST be dropped.
An ICMPv4 error message (Type 3, Code 13 -- Destination Unreachable,
Communication Administratively Prohibited) MAY be sent back to the
lwAFTR. The ICMP policy SHOULD be configurable.
The lwB4 is responsible for performing Application Layer Gateway
(ALG) functions (e.g., SIP, FTP) and other NAPT traversal mechanisms
(e.g., Universal Plug and Play (UPnP) IGD (Internet Gateway Device),
the NAT Port Mapping Protocol (NAT-PMP), manual binding
configuration, PCP) for the internal hosts, if necessary. This
requirement is typical for NAPT44 gateways available today.
It is possible that an lwB4 is co-located in a host. In this case,
the functions of NAPT44 and encapsulation/decapsulation are
implemented inside the host.
5.2.1. Fragmentation Behavior
For TCP and UDP traffic, the NAPT44 implemented in the lwB4 MUST
conform to the behavior and best current practices documented in
[RFC4787], [RFC5508], and [RFC5382]. If the lwB4 supports the
Datagram Congestion Control Protocol (DCCP), then the requirements in
[RFC5597] MUST be implemented.
The NAPT44 in the lwB4 MUST implement ICMP message handling behavior
conforming to the best current practice documented in [RFC5508]. If
the lwB4 receives an ICMP error (for errors detected inside the IPv6
tunnel), the node relays the ICMP error message to the original
source (the lwAFTR). This behavior SHOULD be implemented conforming
to Section 8 of [RFC2473].
If IPv4 hosts behind different lwB4s sharing the same IPv4 address
send fragments to the same IPv4 destination host outside the
Lightweight 4over6 domain, those hosts may use the same IPv4
fragmentation identifier, resulting in incorrect reassembly of the
fragments at the destination host. Given that the IPv4 fragmentation
identifier is a 16-bit field, it could be used similarly to port
ranges: An lwB4 could rewrite the IPv4 fragmentation identifier to be
within its allocated port set, if the resulting fragment identifier
space is large enough related to the rate at which fragments are
Cui, et al. Standards Track [Page 11]
RFC 7596 Lightweight 4over6 July 2015
sent. However, splitting the identifier space in this fashion would
increase the probability of reassembly collision for all connections
through the lwB4. See also Section 5.3.1 of [RFC6864].
6. Lightweight AFTR Behavior
6.1. Binding Table Maintenance
The lwAFTR maintains an address binding table containing the binding
between the lwB4's IPv6 address, the allocated IPv4 address, and the
restricted port set. Unlike the DS-Lite extended binding table,
which is a 5-tuple NAPT table and is defined in Section 6.6 of
[RFC6333], each entry in the Lightweight 4over6 binding table
contains the following 3-tuples:
o IPv6 address for a single lwB4
o Public IPv4 address
o Restricted port set
The entry has two functions: the IPv6 encapsulation of inbound
IPv4 packets destined to the lwB4 and the validation of outbound
IPv4-in-IPv6 packets received from the lwB4 for decapsulation.
The lwAFTR does not perform NAPT and so does not need session
entries.
The lwAFTR MUST synchronize the binding information with the
port-restricted address provisioning process. If the lwAFTR does not
participate in the port-restricted address provisioning process, the
binding MUST be synchronized through other methods (e.g., out-of-band
static update).
If the lwAFTR participates in the port-restricted provisioning
process, then its binding table MUST be created as part of this
process.
For all provisioning processes, the lifetime of binding table entries
MUST be synchronized with the lifetime of address allocations.
Cui, et al. Standards Track [Page 12]
RFC 7596 Lightweight 4over6 July 2015
6.2. lwAFTR Data-Plane Behavior
Several sections of [RFC6333] provide background information on
the AFTR's data-plane functionality and MUST be implemented by the
lwAFTR, as they are common to both solutions. The relevant
sections are:
6.2 Encapsulation Covering encapsulation and
decapsulation of tunneled traffic
6.3 Fragmentation and Reassembly Fragmentation and reassembly
considerations (referencing
[RFC2473])
7.1 Tunneling Covering tunneling and Traffic
Class mapping between IPv4 and IPv6
(referencing [RFC2473]). Also see
[RFC2983]
When the lwAFTR receives an IPv4-in-IPv6 packet from an lwB4, it
decapsulates the IPv6 header and verifies the source addresses and
port in the binding table. If both the source IPv4 and IPv6
addresses match a single entry in the binding table and the source
port is in the allowed port set for that entry, the lwAFTR forwards
the packet to the IPv4 destination.
If no match is found (e.g., no matching IPv4 address entry, port out
of range), the lwAFTR MUST discard or implement a policy (such as
redirection) on the packet. An ICMPv6 Type 1, Code 5 (Destination
Unreachable, source address failed ingress/egress policy) error
message MAY be sent back to the requesting lwB4. The ICMP policy
SHOULD be configurable.
When the lwAFTR receives an inbound IPv4 packet, it uses the IPv4
destination address and port to look up the destination lwB4's IPv6
address in its binding table. If a match is found, the lwAFTR
encapsulates the IPv4 packet. The source is the lwAFTR's IPv6
address, and the destination is the lwB4's IPv6 address from the
matched entry. Then, the lwAFTR forwards the packet to the lwB4
natively over the IPv6 network.
If no match is found, the lwAFTR MUST discard the packet. An ICMPv4
Type 3, Code 1 (Destination Unreachable, Host Unreachable) error
message MAY be sent back. The ICMP policy SHOULD be configurable.
Cui, et al. Standards Track [Page 13]
RFC 7596 Lightweight 4over6 July 2015
The lwAFTR MUST support hairpinning of traffic between two lwB4s, by
performing decapsulation and re-encapsulation of packets from one
lwB4 that need to be sent to another lwB4 associated with the same
AFTR. The hairpinning policy MUST be configurable.
7. Additional IPv4 Address and Port-Set Provisioning Mechanisms
In addition to the DHCPv6-based mechanism described in Section 5.1,
several other IPv4 provisioning protocols have been suggested. These
protocols MAY be implemented. These alternatives include:
o DHCPv4 over DHCPv6: [RFC7341] describes implementing DHCPv4
messages over an IPv6-only service provider's network. This
enables leasing of IPv4 addresses and makes DHCPv4 options
available to the DHCPv4-over-DHCPv6 client. An lwB4 MAY implement
[RFC7341] and [Dyn-Shared-v4Alloc] to retrieve a shared IPv4
address with a set of ports.
o PCP [RFC6887]: an lwB4 MAY use [PCP-PORT_SET] to retrieve a
restricted IPv4 address and a set of ports.
In a Lightweight 4over6 domain, the binding information MUST be
synchronized across the lwB4s, the lwAFTRs, and the provisioning
server.
To prevent interworking complexity, it is RECOMMENDED that an
operator use a single provisioning mechanism / protocol for their
implementation. In the event that more than one provisioning
mechanism / protocol needs to be used (for example, during a
migration to a new provisioning mechanism), the operator SHOULD
ensure that each provisioning mechanism has a discrete set of
resources (e.g., IPv4 address/PSID pools, as well as lwAFTR tunnel
addresses and binding tables).
8. ICMP Processing
For both the lwAFTR and the lwB4, ICMPv6 MUST be handled as described
in [RFC2473].
ICMPv4 does not work in an address-sharing environment without
special handling [RFC6269]. Due to the port-set style of address
sharing, Lightweight 4over6 requires specific ICMP message handling
not required by DS-Lite.
Cui, et al. Standards Track [Page 14]
RFC 7596 Lightweight 4over6 July 2015
8.1. ICMPv4 Processing by the lwAFTR
For inbound ICMP messages, the following behavior SHOULD be
implemented by the lwAFTR to provide ICMP error handling and basic
remote IPv4 service diagnostics for a port-restricted CPE:
1. Check the ICMP Type field.
2. If the ICMP Type field is set to 0 or 8 (echo reply or request),
then the lwAFTR MUST take the value of the ICMP Identifier field
as the source port and use this value to look up the binding
table for an encapsulation destination. If a match is found, the
lwAFTR forwards the ICMP packet to the IPv6 address stored in the
entry; otherwise, it MUST discard the packet.
3. If the ICMP Type field is set to any other value, then the lwAFTR
MUST use the method described in REQ-3 of [RFC5508] to locate the
source port within the transport-layer header in the ICMP
packet's data field. The destination IPv4 address and source
port extracted from the ICMP packet are then used to make a
lookup in the binding table. If a match is found, it MUST
forward the ICMP reply packet to the IPv6 address stored in the
entry; otherwise, it MUST discard the packet.
Otherwise, the lwAFTR MUST discard all inbound ICMPv4 messages.
The ICMP policy SHOULD be configurable.
8.2. ICMPv4 Processing by the lwB4
The lwB4 MUST implement the requirements defined in [RFC5508] for
ICMP forwarding. For ICMP echo request packets originating from the
private IPv4 network, the lwB4 SHOULD implement the method described
in [RFC6346] and use an available port from its port set as the ICMP
identifier.
9. Security Considerations
As the port space for a subscriber shrinks due to address sharing,
the randomness for the port numbers of the subscriber is decreased
significantly. This means that it is much easier for an attacker to
guess the port number used, which could result in attacks ranging
from throughput reduction to broken connections or data corruption.
The port set for a subscriber can be a set of contiguous ports or
non-contiguous ports. Contiguous port sets do not reduce this
threat. However, with non-contiguous port sets (which may be
generated in a pseudorandom way [RFC6431]), the randomness of the
Cui, et al. Standards Track [Page 15]
RFC 7596 Lightweight 4over6 July 2015
port number is improved, provided that the attacker is outside the
Lightweight 4over6 domain and hence does not know the port-set
generation algorithm.
The lwAFTR MUST rate-limit ICMPv6 error messages (see Section 5.1) to
defend against DoS attacks generated by an abuse user.
More considerations about IP address sharing are discussed in
Section 13 of [RFC6269], which is applicable to this solution.
This document describes a number of different protocols that may be
used for the provisioning of lw4o6. In each case, the security
considerations relevant to the provisioning protocol are also
relevant to the provisioning of lw4o6 using that protocol. lw4o6
does not add any other security considerations specific to these
provisioning protocols.
10. References
10.1. Normative References
[RFC1918] Rekhter, Y., Moskowitz, B., Karrenberg, D., de Groot, G.,
and E. Lear, "Address Allocation for Private Internets",
BCP 5, RFC 1918, DOI 10.17487/RFC1918, February 1996,
<http://www.rfc-editor.org/info/rfc1918>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC2473] Conta, A. and S. Deering, "Generic Packet Tunneling in
IPv6 Specification", RFC 2473, DOI 10.17487/RFC2473,
December 1998, <http://www.rfc-editor.org/info/rfc2473>.
[RFC4787] Audet, F., Ed., and C. Jennings, "Network Address
Translation (NAT) Behavioral Requirements for Unicast
UDP", BCP 127, RFC 4787, DOI 10.17487/RFC4787,
January 2007, <http://www.rfc-editor.org/info/rfc4787>.
[RFC5382] Guha, S., Ed., Biswas, K., Ford, B., Sivakumar, S., and P.
Srisuresh, "NAT Behavioral Requirements for TCP", BCP 142,
RFC 5382, DOI 10.17487/RFC5382, October 2008,
<http://www.rfc-editor.org/info/rfc5382>.
Cui, et al. Standards Track [Page 16]
RFC 7596 Lightweight 4over6 July 2015
[RFC5508] Srisuresh, P., Ford, B., Sivakumar, S., and S. Guha, "NAT
Behavioral Requirements for ICMP", BCP 148, RFC 5508,
DOI 10.17487/RFC5508, April 2009,
<http://www.rfc-editor.org/info/rfc5508>.
[RFC5597] Denis-Courmont, R., "Network Address Translation (NAT)
Behavioral Requirements for the Datagram Congestion
Control Protocol", BCP 150, RFC 5597,
DOI 10.17487/RFC5597, September 2009,
<http://www.rfc-editor.org/info/rfc5597>.
[RFC6333] Durand, A., Droms, R., Woodyatt, J., and Y. Lee,
"Dual-Stack Lite Broadband Deployments Following IPv4
Exhaustion", RFC 6333, DOI 10.17487/RFC6333, August 2011,
<http://www.rfc-editor.org/info/rfc6333>.
[RFC7598] Mrugalski, T., Troan, O., Farrer, I., Perreault, S., Dec,
W., Bao, C., Yeh, L., and X. Deng, "DHCPv6 Options for
Configuration of Softwire Address and Port-Mapped
Clients", RFC 7598, DOI 10.17487/RFC7598, July 2015,
<http://www.rfc-editor.org/info/rfc7598>.
10.2. Informative References
[B4-Trans-DSLite]
Cui, Y., Sun, Q., Boucadair, M., Tsou, T., Lee, Y., and
I. Farrer, "Lightweight 4over6: An Extension to the
DS-Lite Architecture", Work in Progress,
draft-cui-softwire-b4-translated-ds-lite-11,
February 2013.
[DSLite-LW-Ext]
Deng, X., Boucadair, M., and C. Zhou, "NAT offload
extension to Dual-Stack lite", Work in Progress,
draft-zhou-softwire-b4-nat-04, October 2011.
[Dyn-Shared-v4Alloc]
Cui, Y., Sun, Q., Farrer, I., Lee, Y., Sun, Q., and
M. Boucadair, "Dynamic Allocation of Shared IPv4
Addresses", Work in Progress,
draft-ietf-dhc-dynamic-shared-v4allocation-09, May 2015.
[PCP-PORT_SET]
Sun, Q., Boucadair, M., Sivakumar, S., Zhou, C., Tsou, T.,
and S. Perreault, "Port Control Protocol (PCP) Extension
for Port Set Allocation", Work in Progress,
draft-ietf-pcp-port-set-09, May 2015.
Cui, et al. Standards Track [Page 17]
RFC 7596 Lightweight 4over6 July 2015
[RFC2827] Ferguson, P. and D. Senie, "Network Ingress Filtering:
Defeating Denial of Service Attacks which employ IP Source
Address Spoofing", BCP 38, RFC 2827, DOI 10.17487/RFC2827,
May 2000, <http://www.rfc-editor.org/info/rfc2827>.
[RFC2983] Black, D., "Differentiated Services and Tunnels",
RFC 2983, DOI 10.17487/RFC2983, October 2000,
<http://www.rfc-editor.org/info/rfc2983>.
[RFC3022] Srisuresh, P. and K. Egevang, "Traditional IP Network
Address Translator (Traditional NAT)", RFC 3022,
DOI 10.17487/RFC3022, January 2001,
<http://www.rfc-editor.org/info/rfc3022>.
[RFC6269] Ford, M., Ed., Boucadair, M., Durand, A., Levis, P., and
P. Roberts, "Issues with IP Address Sharing", RFC 6269,
DOI 10.17487/RFC6269, June 2011,
<http://www.rfc-editor.org/info/rfc6269>.
[RFC6346] Bush, R., Ed., "The Address plus Port (A+P) Approach to
the IPv4 Address Shortage", RFC 6346,
DOI 10.17487/RFC6346, August 2011,
<http://www.rfc-editor.org/info/rfc6346>.
[RFC6431] Boucadair, M., Levis, P., Bajko, G., Savolainen, T., and
T. Tsou, "Huawei Port Range Configuration Options for PPP
IP Control Protocol (IPCP)", RFC 6431,
DOI 10.17487/RFC6431, November 2011,
<http://www.rfc-editor.org/info/rfc6431>.
[RFC6864] Touch, J., "Updated Specification of the IPv4 ID Field",
RFC 6864, DOI 10.17487/RFC6864, February 2013,
<http://www.rfc-editor.org/info/rfc6864>.
[RFC6887] Wing, D., Ed., Cheshire, S., Boucadair, M., Penno, R., and
P. Selkirk, "Port Control Protocol (PCP)", RFC 6887,
DOI 10.17487/RFC6887, April 2013,
<http://www.rfc-editor.org/info/rfc6887>.
[RFC7040] Cui, Y., Wu, J., Wu, P., Vautrin, O., and Y. Lee, "Public
IPv4-over-IPv6 Access Network", RFC 7040,
DOI 10.17487/RFC7040, November 2013,
<http://www.rfc-editor.org/info/rfc7040>.
[RFC7341] Sun, Q., Cui, Y., Siodelski, M., Krishnan, S., and I.
Farrer, "DHCPv4-over-DHCPv6 (DHCP 4o6) Transport",
RFC 7341, DOI 10.17487/RFC7341, August 2014,
<http://www.rfc-editor.org/info/rfc7341>.
Cui, et al. Standards Track [Page 18]
RFC 7596 Lightweight 4over6 July 2015
[RFC7597] Troan, O., Ed., Dec, W., Li, X., Bao, C., Matsushima, S.,
Murakami, T., and T. Taylor, Ed., "Mapping of Address and
Port with Encapsulation (MAP-E)", RFC 7597,
DOI 10.17487/RFC7597, July 2015,
<http://www.rfc-editor.org/info/rfc7597>.
[Stateless-DS-Lite]
Penno, R., Durand, A., Clauberg, A., and L. Hoffmann,
"Stateless DS-Lite", Work in Progress,
draft-penno-softwire-sdnat-02, March 2012.
[TR069] Broadband Forum TR-069, "CPE WAN Management Protocol",
Amendment 5, CWMP Version: 1.4, November 2013,
<https://www.broadband-forum.org>.
[Unified-v4-in-v6]
Boucadair, M., Farrer, I., Perreault, S., Ed., and S.
Sivakumar, Ed., "Unified IPv4-in-IPv6 Softwire CPE", Work
in Progress, draft-ietf-softwire-unified-cpe-01, May 2013.
Acknowledgements
The authors would like to thank Ole Troan, Ralph Droms, and Suresh
Krishnan for their comments and feedback.
This document is a merge of three documents: [B4-Trans-DSLite],
[DSLite-LW-Ext], and [Stateless-DS-Lite].
Contributors
The following individuals contributed to this effort:
Jianping Wu
Tsinghua University
Department of Computer Science, Tsinghua University
Beijing 100084
China
Phone: +86-10-62785983
Email: jianping@cernet.edu.cn
Peng Wu
Tsinghua University
Department of Computer Science, Tsinghua University
Beijing 100084
China
Phone: +86-10-62785822
Email: pengwu.thu@gmail.com
Cui, et al. Standards Track [Page 19]
RFC 7596 Lightweight 4over6 July 2015
Qi Sun
Tsinghua University
Beijing 100084
China
Phone: +86-10-62785822
Email: sunqi@csnet1.cs.tsinghua.edu.cn
Chongfeng Xie
China Telecom
Room 708, No. 118, Xizhimennei Street
Beijing 100035
China
Phone: +86-10-58552116
Email: xiechf@ctbri.com.cn
Xiaohong Deng
The University of New South Wales
Sydney NSW 2052
Australia
Email: dxhbupt@gmail.com
Cathy Zhou
Huawei Technologies
Section B, Huawei Industrial Base, Bantian Longgang
Shenzhen 518129
China
Email: cathyzhou@huawei.com
Alain Durand
Juniper Networks
1194 North Mathilda Avenue
Sunnyvale, CA 94089-1206
United States
Email: adurand@juniper.net
Reinaldo Penno
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134
United States
Email: repenno@cisco.com
Cui, et al. Standards Track [Page 20]
RFC 7596 Lightweight 4over6 July 2015
Axel Clauberg
Deutsche Telekom AG
CTO-ATI
Landgrabenweg 151
Bonn 53227
Germany
Email: axel.clauberg@telekom.de
Lionel Hoffmann
Bouygues Telecom
TECHNOPOLE
13/15 Avenue du Marechal Juin
Meudon 92360
France
Email: lhoffman@bouyguestelecom.fr
Maoke Chen (a.k.a. Noriyuki Arai)
BBIX, Inc.
Tokyo Shiodome Building, Higashi-Shimbashi 1-9-1
Minato-ku, Tokyo 105-7310
Japan
Email: maoke@bbix.net
Authors' Addresses
Yong Cui
Tsinghua University
Beijing 100084
China
Phone: +86-10-62603059
Email: yong@csnet1.cs.tsinghua.edu.cn
Qiong Sun
China Telecom
Room 708, No. 118, Xizhimennei Street
Beijing 100035
China
Phone: +86-10-58552936
Email: sunqiong@ctbri.com.cn
Cui, et al. Standards Track [Page 21]
RFC 7596 Lightweight 4over6 July 2015
Mohamed Boucadair
France Telecom
Rennes 35000
France
Email: mohamed.boucadair@orange.com
Tina Tsou
Huawei Technologies
2330 Central Expressway
Santa Clara, CA 95050
United States
Phone: +1-408-330-4424
Email: tena@huawei.com
Yiu L. Lee
Comcast
One Comcast Center
Philadelphia, PA 19103
United States
Email: yiu_lee@cable.comcast.com
Ian Farrer
Deutsche Telekom AG
CTO-ATI, Landgrabenweg 151
Bonn, NRW 53227
Germany
Email: ian.farrer@telekom.de
Cui, et al. Standards Track [Page 22]