Internet Engineering Task Force (IETF) B. Claise Request for Comments: 6759 P. Aitken Category: Informational N. Ben-Dvora ISSN: 2070-1721 Cisco Systems, Inc. November 2012 Cisco Systems Export of Application Information in IP Flow Information Export (IPFIX) Abstract This document specifies a Cisco Systems extension to the IPFIX information model specified in RFC 5102 to export application information. Status of This Memo This document is not an Internet Standards Track specification; it is published for informational purposes. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Not all documents approved by the IESG are a candidate for any level of Internet Standard; see Section 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc6759. Copyright Notice Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Claise, et al. Informational [Page 1] RFC 6759 Export of App. Info. in IPFIX November 2012 Table of Contents 1. Introduction ....................................................3 1.1. Application Information Use Cases ..........................5 1.2. Conventions Used in This Document ..........................5 2. IPFIX Documents Overview ........................................5 3. Terminology .....................................................6 3.1. New Terminology ............................................6 4. applicationId Information Element Specification .................6 4.1. Existing Classification Engine IDs .........................7 4.2. Selector ID Length per Classification ID ..................11 4.3. Application Name Options Template Record ..................12 4.4. Resolving IANA L4 Port Discrepancies ......................13 5. Grouping Applications with Attributes ..........................13 5.1. Options Template Record for Attribute Values ..............15 6. Application ID Examples ........................................15 6.1. Example 1: Layer 2 Protocol ...............................15 6.2. Example 2: Standardized IANA Layer 3 Protocol .............16 6.3. Example 3: Proprietary Layer 3 Protocol ...................17 6.4. Example 4: Standardized IANA Layer 4 Port .................18 6.5. Example 5: Layer 7 Application ............................19 6.6. Example 6: Layer 7 Application with Private Enterprise Number (PEN) ...................................21 6.7. Example: Port Obfuscation .................................22 6.8. Example: Application Name Mapping Options Template ........23 6.9. Example: Attributes Values Options Template Record ........24 7. IANA Considerations ............................................25 7.1. New Information Elements ..................................25 7.1.1. applicationDescription .............................25 7.1.2. applicationId ......................................26 7.1.3. applicationName ....................................26 7.1.4. classificationEngineId .............................26 7.1.5. applicationCategoryName ............................29 7.1.6. applicationSubCategoryName .........................29 7.1.7. applicationGroupName ...............................29 7.1.8. p2pTechnology ......................................29 7.1.9. tunnelTechnology ...................................30 7.1.10. encryptedTechnology ...............................30 7.2. Classification Engine ID Registry .........................30 8. Security Considerations ........................................30 9. References .....................................................31 9.1. Normative References ......................................31 9.2. Informative References ....................................32 10. Acknowledgements ..............................................33 Appendix A. Additions to XML Specification of IPFIX Information (Non-normative) .......................................34 Appendix B. Port Collisions Tables (Non-normative) ................39 Appendix C. Application Registry Example (Non-normative) ..........43 Claise, et al. Informational [Page 2] RFC 6759 Export of App. Info. in IPFIX November 2012 List of Figures Figure 1: applicationId Information Element .......................7 Figure 2: Selector ID Encoding ...................................12 List of Tables Table 1: Existing Classification Engine IDs .......................7 Table 2: Selector ID Default Length per Classification Engine ID ...............................................11 Table 3: Application ID Static Attributes ........................13 Table 4: Different Protocols on UDP and TCP ......................39 Table 5: Different Protocols on SCTP and TCP .....................40 1. Introduction Today, service providers and network administrators are looking for visibility into the packet content rather than just the packet header. Some network devices' Metering Processes inspect the packet content and identify the applications that are utilizing the network traffic. Applications in this context are defined as networking protocols used by networking processes that exchange packets between them (such as web applications, peer-to-peer applications, file transfer, e-mail applications, etc.). Applications can be further characterized by other criteria, some of which are application specific. Examples include: web application to a specific domain, per-user specific traffic, a video application with a specific codec, etc. The application identification is based on several different methods or even a combination of methods: 1. L2 (Layer 2) protocols (such as ARP (Address Resolution Protocol), PPP (Point-to-Point Protocol), LLDP (Link Layer Discovery Protocol)) 2. IP protocols (such as ICMP (Internet Control Message Protocol), IGMP (Internet Group Management Protocol), GRE (Generic Routing Encapsulation) 3. TCP or UDP ports (such as HTTP, Telnet, FTP) 4. Application layer header (of the application to be identified) 5. Packet data content 6. Packets and traffic behavior Claise, et al. Informational [Page 3] RFC 6759 Export of App. Info. in IPFIX November 2012 The exact application identification methods are part of the Metering Process internals that aim to provide an accurate identification and minimize false identification. This task requires a sophisticated Metering Process since the protocols do not behave in a standard manner. 1. Applications use port obfuscation where the application runs on a different port than the IANA assigned one. For example, an HTTP server might run on TCP port 23 (assigned to telnet in [IANA-PORTS]). 2. IANA port registries do not accurately reflect how certain ports are "commonly" used today. Some ports are reserved, but the application either never became prevalent or is not in use today. 3. The application behavior and identification logic become more and more complex. For that reason, such Metering Processes usually detect applications based on multiple mechanisms in parallel. Detection based only on port matching might wrongly identify the application. If the Metering Process is capable of detecting applications more accurately, it is considered to be stronger and more accurate. Similarly, a reporting mechanism that uses L4 port based applications only, such as L4:, would have similar issues. The reporting system should be capable of reporting the applications classified using all types of mechanisms. In particular, applications that do not have any IANA port definition. While a mechanism to export application information should be defined, the L4 port being used must be exported using the destination port (destinationTransportPort at [IANA-IPFIX]) in the corresponding IPFIX record. Applications could be identified at different OSI layers, from layer 2 to layer 7. For example, the Link Layer Distribution Protocol (LLDP) [LLDP] can be identified in layer 2, ICMP can be identified in layer 3 [IANA-PROTO], HTTP can be identified in layer 4 [IANA-PORTS], and Webex can be identified in layer 7. While an ideal solution would be an IANA registry for applications above (or inside the payload of) the well-known ports [IANA-PORTS], this solution is not always possible. Indeed, the specifications for some applications embedded in the payload are not available. Some reverse engineering as well as a ubiquitous language for application identification would be required conditions to be able to manage an IANA registry for these types of applications. Clearly, these are blocking factors. Claise, et al. Informational [Page 4] RFC 6759 Export of App. Info. in IPFIX November 2012 This document specifies the Cisco Systems application information encoding (as described in Section 4) to export the application information with the IPFIX protocol [RFC5101]. However, the layer 7 application registry values are out of scope of this document. 1.1. Application Information Use Cases There are several use cases for application information: 1. Application Visibility This is one of the main cases for using application information. Network administrators are using application visibility to understand the main network consumers, network trends, and user behavior. 2. Security Functions Application knowledge is sometimes used in security functions in order to provide comprehensive functions such as Application-based firewall, URL filtering, parental control, intrusion detection, etc. All of the above use cases require exporting application information to provide the network function itself or to log the network function operation. 1.2. Conventions Used in This Document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 2. IPFIX Documents Overview The IPFIX protocol [RFC5101] provides network administrators with access to IP Flow information. The architecture for the export of measured IP Flow information out of an IPFIX Exporting Process to a Collecting Process is defined in the IPFIX Architecture [RFC5470], per the requirements defined in RFC 3917 [RFC3917]. The IPFIX Architecture [RFC5470] specifies how IPFIX Data Records and Templates are carried via a congestion-aware transport protocol from IPFIX Exporting Processes to IPFIX Collecting Processes. Claise, et al. Informational [Page 5] RFC 6759 Export of App. Info. in IPFIX November 2012 IPFIX has a formal description of IPFIX Information Elements, their names, types, and additional semantic information, as specified in the IPFIX information model [RFC5102]. In order to gain a level of confidence in the IPFIX implementation, probe the conformity and robustness, and allow interoperability, the Guidelines for IPFIX Testing [RFC5471] presents a list of tests for implementers of compliant Exporting Processes and Collecting Processes. The Bidirectional Flow Export [RFC5103] specifies a method for exporting bidirectional flow (biflow) information using the IPFIX protocol, representing each biflow using a single Flow Record. "Reducing Redundancy in IP Flow Information Export (IPFIX) and Packet Sampling (PSAMP) Reports" [RFC5473] specifies a bandwidth-saving method for exporting Flow or packet information, by separating information common to several Flow Records from information specific to an individual Flow Record: common Flow information is exported only once. 3. Terminology IPFIX-specific terminology used in this document is defined in Section 2 of the IPFIX protocol specification [RFC5101]. As in [RFC5101], these IPFIX-specific terms have the first letter of a word capitalized when used in this document. 3.1. New Terminology Application ID A unique identifier for an application. When an application is detected, the most granular application is encoded in the Application ID. 4. applicationId Information Element Specification This document specifies the applicationId Information Element, which is a single field composed of two parts: 1. 8 bits of Classification Engine ID. The Classification Engine can be considered as a specific registry for application assignments. 2. n bits of Selector ID. The Selector ID length varies depending on the Classification Engine ID. Claise, et al. Informational [Page 6] RFC 6759 Export of App. Info. in IPFIX November 2012 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Class. Eng. ID| Selector ID ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1: applicationId Information Element Classification Engine ID A unique identifier for the engine that determined the Selector ID. Thus, the Classification Engine ID defines the context for the Selector ID. Selector ID A unique identifier of the application for a specific Classification Engine ID. Note that the Selector ID length varies depending on the Classification Engine ID. The Selector ID term is a similar concept to the selectorId Information Element, specified in the PSAMP Protocol [RFC5476][RFC5477]. 4.1. Existing Classification Engine IDs The following Classification Engine IDs have been allocated: Name Value Description 0 Invalid. IANA-L3 1 The Assigned Internet Protocol Number (layer 3 (L3)) is exported in the Selector ID. See [IANA-PROTO]. PANA-L3 2 Proprietary layer 3 definition. An enterprise can export its own layer 3 protocol numbers. The Selector ID has a global significance for all devices from the same enterprise. Claise, et al. Informational [Page 7] RFC 6759 Export of App. Info. in IPFIX November 2012 IANA-L4 3 The IANA layer 4 (L4) well-known port number is exported in the Selector ID. See [IANA-PORTS]. Note: as an IPFIX flow is unidirectional, it contains the destination port. PANA-L4 4 Proprietary layer 4 definition. An enterprise can export its own layer 4 port numbers. The Selector ID has global significance for devices from the same enterprise. Example: IPFIX was pre-assigned the port 4739 using the IANA early allocation process [RFC4020] years before the document was published as an RFC. While waiting for the RFC and its associated IANA registration, Selector ID 4739 was used with this PANA-L4. 5 Reserved. USER- 6 The Selector ID represents Defined applications defined by the user (using CLI, GUI, etc.) based on the methods described in Section 1. The Selector ID has a local significance per device. 7 Reserved. 8 Reserved. 9 Reserved. 10 Reserved. 11 Reserved. PANA-L2 12 Proprietary layer 2 (L2) definition. An enterprise can export its own layer 2 identifiers. The Selector ID represents the enterprise's unique global layer 2 applications. The Selector ID has a global significance for all Claise, et al. Informational [Page 8] RFC 6759 Export of App. Info. in IPFIX November 2012 devices from the same enterprise. Examples include Cisco Subnetwork Access Protocol (SNAP). PANA-L7 13 Proprietary layer 7 definition. The Selector ID represents the enterprise's unique global ID for layer 7 applications. The Selector ID has a global significance for all devices from the same enterprise. This Classification Engine ID is used when the application registry is owned by the Exporter manufacturer (referred to as the "enterprise" in this document). 14 Reserved. 15 Reserved. 16 Reserved. 17 Reserved. ETHERTYPE 18 The Selector ID represents the well-known Ethertype. See [ETHERTYPE]. LLC 19 The Selector ID represents the well-known IEEE 802.2 Link Layer Control (LLC) Destination Service Access Point (DSAP). See [LLC]. PANA-L7- 20 Proprietary layer 7 definition, PEN including a Private Enterprise Number (PEN) [IANA-PEN] to identify that the application registry being used is not owned by the Exporter manufacturer or to identify the original enterprise in the case of a mediator or 3rd party device. The Selector ID represents the enterprise unique global ID for the layer 7 applications. The Claise, et al. Informational [Page 9] RFC 6759 Export of App. Info. in IPFIX November 2012 Selector ID has a global significance for all devices from the same enterprise. 21 to 255 Available (255 is the maximum Engine ID) Table 1: Existing Classification Engine IDs "PANA = Proprietary Assigned Number Authority". In other words, an enterprise specific version of IANA for internal IDs. The PANA-L7 Classification Engine ID SHOULD be used when the application registry is owned by the Exporter manufacturer. Even if the application registry is owned by the Exporter manufacturer, the PANA-L7-PEN MAY be used, specifying the manufacturer. For example, if Exporter A (from enterprise-A) wants to export its enterprise-A L7 registry, then it uses the PANA-L7 Classification Engine ID. If Exporter B (from enterprise-B) wants to export its enterprise-B L7 registry, then it also uses the PANA-L7 Classification Engine ID. The mechanism for the Collector to know about the Exporter PEN is out of scope of this document. Possible tracks are SNMP polling, an Options Template exporting the privateEnterpriseNumber Information Element [IANA-IPFIX], hardcoded value, etc. An Exporter may classify the application according to another vendor's application registry. For example, an IPFIX Mediator [RFC6183] may need to re-export applications received from different Exporters using different PANA-L7 application registries. For example, if Exporter C (from enterprise-C) wants to reuse enterprise- D's application registry, then it uses PANA-L7-PEN with enterprise- D's PEN. When reporting application information from multiple Exporters from different enterprises (different PENs), the PANA-L7-PEN Classification Engine MUST be used in exported Flow Records, which allows the original enterprise ID to be reported. The ID of the enterprise that defined the Application ID is identified by the enterprise's PEN. For example, an IPFIX Mediator aggregates traffic from some Exporters which report enterprise-E applications and other Exporters that report enterprise-F applications. An example is displayed in Section 6.6. Claise, et al. Informational [Page 10] RFC 6759 Export of App. Info. in IPFIX November 2012 Note that the PANA-L7 Classification Engine ID is also used for resolving IANA L4 port Discrepancies (see Section 4.4). The list in Table 1 is maintained by IANA thanks to the registry within the classificationEngineId Information Element. See the IANA Considerations section. The Classification Engine ID is part of the Application ID encoding, so the classificationEngineId Information Element is currently not required by the specifications in this document. However, this Information Element was created for completeness, as it was anticipated that this Information Element will be required in the future. 4.2. Selector ID Length per Classification ID As the Selector ID part of the Application ID is variable based on the Classification Engine ID value, the applicationId SHOULD be encoded in a variable-length Information Element [RFC5101] for IPFIX export. The following table displays the Selector ID default length for the different Classification Engine IDs. Classification Selector ID default Engine ID Name length (in bytes) IANA-L3 1 PANA-L3 1 IANA-L4 2 PANA-L4 2 USER-Defined 3 PANA-L2 5 PANA-L7 3 ETHERTYPE 2 LLC 1 PANA-L7-PEN 3 (*) Table 2: Selector ID Default Length per Classification Engine ID Claise, et al. Informational [Page 11] RFC 6759 Export of App. Info. in IPFIX November 2012 (*) There are an extra 4 bytes for the PEN. However, the PEN is not considered part of the Selector ID. If a legacy protocol such as NetFlow version 9 [RFC3954] is used, and this protocol doesn't support variable-length Information Elements, then either multiple Template Records (one per applicationId length), or a single Template Record corresponding to the maximum sized applicationId MUST be used. Application IDs MAY be encoded in a smaller number of bytes, following the same rules as for IPFIX Reduced Size Encoding [RFC5101]. Application IDs MAY be encoded with a larger length. For example, a normal IANA L3 protocol encoding would take 2 bytes since the Selector ID represents the protocol field from the IP header encoded in one byte. However, an IANA L3 protocol encoding may be encoded with 3 bytes. In this case, the Selector ID value MUST always be encoded in the least significant bits as shown in Figure 2. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Class. Eng. ID |zero-valued upper-bits ... Selector ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 2: Selector ID Encoding 4.3. Application Name Options Template Record For Classification Engines that specify locally unique Application IDs (which means unique per engine and per router), an Options Template Record (see [RFC5101]) MUST be used to export the correspondence between the Application ID, the Application Name, and the Application Description. For Classification Engines that specify globally unique Application IDs, an Options Template Record MAY be used to export the correspondence between the Application ID, the Application Name and the Application Description, unless the mapping is hardcoded in the Collector, or known out of band (for example, by polling a MIB). An example Options Template is shown in Section 6.8. Enterprises may assign company-wide Application ID values for the PANA-L7 Classification Engine. In this case, a possible optimization for the Collector is to keep the mappings between the Application IDs and the Application Names per enterprise, as opposed to per Exporter. Claise, et al. Informational [Page 12] RFC 6759 Export of App. Info. in IPFIX November 2012 4.4. Resolving IANA L4 Port Discrepancies Even though IANA L4 ports usually point to the same protocols for both UDP, TCP or other transport types, there are some exceptions, as mentioned in Appendix B. Instead of imposing the transport protocol (UDP/TCP/SCTP/etc.) in the scope of the "Application Name Options Template Record" (Section 6.8) for all applications (in addition to having the transport protocol as a key-field in the Flow Record definition), the convention is that the L4 application is always TCP related. So, whenever the Collector has a conflict in looking up IANA, it would choose the TCP choice. As a result, the UDP L4 applications from Table 3 and the SCTP L4 applications from Table 4 are assigned in the PANA_L7 Application ID range, i.e., under Classification Engine ID 13. Currently, there are no discrepancies between the well-known ports for TCP and the Datagram Congestion Control Protocol (DCCP). 5. Grouping Applications with Attributes Due to the high number of different Application IDs, Application IDs MAY be categorized into groups. This offers the benefits of easier reporting and action, such as QoS policies. Indeed, most applications with the same characteristics should be treated the same way; for example, all video traffic. Attributes are statically assigned per Application ID and are independent of the traffic. The attributes are listed below: Name Description Category An attribute that provides a first- level categorization for each Application ID. Examples include browsing, email, file-sharing, gaming, instant messaging, voice- and-video, etc. The category attribute is encoded by the applicationCategoryName Information Element. Sub-Category An attribute that provides a second- level categorization for each Application ID. Examples include backup-systems, client-server, database, routing-protocol, etc. The sub-category attribute is Claise, et al. Informational [Page 13] RFC 6759 Export of App. Info. in IPFIX November 2012 encoded by the applicationSubCategoryName Information Element. Application- An attribute that groups multiple Group Application IDs that belong to the same networking application. For example, the ftp-group contains ftp-data (port 20), ftp (port 20), ni-ftp (port 47), sftp (port 115), bftp (port 152), ftp-agent(port 574), ftps-data (port 989). The application-group attribute is encoded by the applicationGroupName Information Element. P2P-Technology Specifies if the Application ID is based on peer-to-peer technology. The P2P-technology attribute is encoded by the p2pTechnology Information Element. Tunnel- Specifies if the Application ID is Technology used as a tunnel technology. The tunnel-technology attribute is encoded by the tunnelTechnology Information Element. Encrypted Specifies if the Application ID is an encrypted networking protocol. The encrypted attribute is encoded by the encryptedTechnology Information Element. Table 3: Application ID Static Attributes Every application is assigned to one applicationCategoryName, one applicationSubCategoryName, one applicationGroupName, and it has one p2pTechnology, one tunnelTechnology, and one encryptedTechnology. These new Information Elements are specified in the IANA Considerations section (Section 7.1). Maintaining the attribute values in IANA seems impossible to realize. Therefore, the attribute values per application are enterprise specific. Claise, et al. Informational [Page 14] RFC 6759 Export of App. Info. in IPFIX November 2012 5.1. Options Template Record for Attribute Values An Options Template Record (see [RFC5101]) SHOULD be used to export the correspondence between each Application ID and its related Attribute values. An alternative way for the Collecting Process to learn the correspondence is to populate these mappings out of band, for example, by loading a CSV file containing the correspondence table. The Attributes Option Template contains the application ID as a scope field, followed by the applicationCategoryName, the applicationSubCategoryName, the applicationGroupName, the p2pTechnology, the tunnelTechnology, and the encryptedTechnology Information Elements. A list of attributes may conveniently be exported using a subTemplateList per [RFC6313]. An example is given in Section 6.9. 6. Application ID Examples The following examples are created solely for the purpose of illustrating how the extensions proposed in this document are encoded. 6.1. Example 1: Layer 2 Protocol The list of Classification Engine IDs in Table 1 shows that the layer 2 Classification Engine IDs are 12 (PANA-L2), 18, (ETHERTYPE) and 19 (LLC). From the Ethertype list, LLDP [LLDP] has the Selector ID value 0x88CC, so 35020 in decimal: NAME Selector ID LLDP 35020 So, in the case of LLDP, the Classification Engine ID is 18 (LLC) while the Selector ID has the value 35020. Per Section 4, the applicationId Information Element is a single field composed of 8 bits of Classification Engine ID, followed by n bits of Selector ID. From Table 2, the Selector ID length n is 2 for the ETHERTYPE Engine ID. Claise, et al. Informational [Page 15] RFC 6759 Export of App. Info. in IPFIX November 2012 Therefore, the Application ID is encoded as: 0 1 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 18 | 35020 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ So the Application ID has the decimal value of 1214668. The format '18..35020' is used for simplicity in the examples below, to clearly express that two components of the Application ID. The Exporting Process creates a Template Record with a few Information Elements: amongst other things, the Application ID. For example: - applicationId (key field) - octetTotalCount (non-key field) For example, a Flow Record corresponding to the above Template Record may contain: { applicationId='18..35020', octetTotalCount=123456 } The Collector has all the required information to determine that the application is LLDP, because the Application ID uses a global and well-known registry, i.e., the Ethertype. The Collector can determine which application is represented by the Application ID by loading the registry out of band. 6.2. Example 2: Standardized IANA Layer 3 Protocol From the list of Classification Engine IDs in Table 1, the IANA layer 3 Classification Engine ID (IANA-L3) is 1. From Table 2 the Selector ID length is 1 for the IANA-L3 Engine ID. From the list of IANA layer 3 protocols (see [IANA-PROTO]), ICMP has the value 1: Decimal Keyword Protocol Reference 1 ICMP Internet Control [RFC792] Message So, in the case of the standardized IANA layer 3 protocol ICMP, the Classification Engine ID is 1, and the Selector ID has the value of 1. Claise, et al. Informational [Page 16] RFC 6759 Export of App. Info. in IPFIX November 2012 Therefore, the Application ID is encoded as: 0 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 1 | 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ So, the Application ID has the value of 257. The format '1..1' is used for simplicity in the examples below. The Exporting Process creates a Template Record with a few Information Elements: amongst other things, the Application ID. For example: - sourceIPv4Address (key field) - destinationIPv4Address (key field) - ipDiffServCodePoint (key field) - applicationId (key field) - octetTotalCount (non-key field) For example, a Flow Record corresponding to the above Template Record may contain: { sourceIPv4Address=192.0.2.1, destinationIPv4Address=192.0.2.2, ipDiffServCodePoint=0, applicationId='1..1', octetTotalCount=123456 } The Collector has all the required information to determine that the application is ICMP, because the Application ID uses a global and well-known registry, i.e., the IANA L3 protocol number. 6.3. Example 3: Proprietary Layer 3 Protocol Assume that an enterprise has specified a new layer 3 protocol called "foo". From the list of Classification Engine IDs in Table 1, the proprietary layer 3 Classification Engine ID (PANA-L3) is 2. From Table 2 the Selector ID length is 1 for the PANA-L3 Engine ID. A global registry within the enterprise specifies that the "foo" protocol has the value 90: Protocol Protocol ID foo 90 Claise, et al. Informational [Page 17] RFC 6759 Export of App. Info. in IPFIX November 2012 So, in the case of the layer 3 protocol foo specified by this enterprise, the Classification Engine ID is 2, and the Selector ID has the value of 90. Therefore, the Application ID is encoded as: 0 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 2 | 90 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ So the Application ID has the value of 602. The format '2..90' is used for simplicity in the examples below. The Exporting Process creates a Template Record with a few Information Elements: amongst other things, the Application ID. For example: - sourceIPv4Address (key field) - destinationIPv4Address (key field) - ipDiffServCodePoint (key field) - applicationId (key field) - octetTotalCount (non-key field) For example, a Flow Record corresponding to the above Template Record may contain: { sourceIPv4Address=192.0.2.1, destinationIPv4Address=192.0.2.2, ipDiffServCodePoint=0, applicationId='2..90', octetTotalCount=123456 } Along with this Flow Record, a new Options Template Record would be exported, as shown in Section 6.8. 6.4. Example 4: Standardized IANA Layer 4 Port From the list of Classification Engine IDs in Table 1, the IANA layer 4 Classification Engine ID (IANA-L4) is 3. From Table 2 the Selector ID length is 2 for the IANA-L4 Engine ID. From the list of IANA layer 4 ports (see [IANA-PORTS]), SNMP has the value 161: Claise, et al. Informational [Page 18] RFC 6759 Export of App. Info. in IPFIX November 2012 Keyword Decimal Description snmp 161/tcp SNMP snmp 161/udp SNMP So, in the case of the standardized IANA layer 4 SNMP port, the Classification Engine ID is 3, and the Selector ID has the value of 161. Therefore, the Application ID is encoded as: 0 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 3 | 161 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ So the Application ID has the value of 196769. The format '3..161' is used for simplicity in the examples below. The Exporting Process creates a Template Record with a few Information Elements: amongst other things, the Application ID. For example: - sourceIPv4Address (key field) - destinationIPv4Address (key field) - protocol (key field) - ipDiffServCodePoint (key field) - applicationId (key field) - octetTotalCount (non-key field) For example, a Flow Record corresponding to the above Template Record may contain: { sourceIPv4Address=192.0.2.1, destinationIPv4Address=192.0.2.2, protocol=17, ipDiffServCodePoint=0, applicationId='3..161', octetTotalCount=123456 } The Collector has all the required information to determine that the application is SNMP, because the Application ID uses a global and well-known registry, i.e., the IANA L4 protocol number. 6.5. Example 5: Layer 7 Application In this example, the Metering Process has observed some Webex traffic. Claise, et al. Informational [Page 19] RFC 6759 Export of App. Info. in IPFIX November 2012 From the list of Classification Engine IDs in Table 1, the layer 7 unique Classification Engine ID (PANA-L7) is 13. From Table 2 the Selector ID length is 3 for the PANA-L7 Engine ID. Suppose that the Metering Process returns the ID 10000 for Webex traffic. So, in the case of this Webex application, the Classification Engine ID is 13 and the Selector ID has the value of 10000. Therefore, the Application ID is encoded as: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 13 | 10000 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ So the Application ID has the value of 218113808. The format '13..10000' is used for simplicity in the examples below. The Exporting Process creates a Template Record with a few Information Elements: amongst other things, the Application ID. For example: - sourceIPv4Address (key field) - destinationIPv4Address (key field) - ipDiffServCodePoint (key field) - applicationId (key field) - octetTotalCount (non-key field) For example, a Flow Record corresponding to the above Template Record may contain: { sourceIPv4Address=192.0.2.1, destinationIPv4Address=192.0.2.2, ipDiffServCodePoint=0, applicationId='13..10000', octetTotalCount=123456 } The 10000 value is globally unique for the enterprise, so that the Collector can determine which application is represented by the Application ID by loading the registry out of band. Along with this Flow Record, a new Options Template Record would be exported, as shown in Section 6.8. Claise, et al. Informational [Page 20] RFC 6759 Export of App. Info. in IPFIX November 2012 6.6. Example 6: Layer 7 Application with Private Enterprise Number (PEN) In this example, the layer 7 Webex traffic from Example 5 above have been classified by enterprise X. The exported records have been received by enterprise Y's mediation device, which wishes to forward them to a top-level Collector. In order for the top-level Collector to know that the records were classified by enterprise X, the enterprise Y mediation device must report the records using the PANA-L7-PEN Classification Engine ID with enterprise X's Private Enterprise Number. The PANA-L7-PEN Classification Engine ID is 20, and enterprise X's Selector ID for Webex traffic has the value of 10000. From Table 2 the Selector ID length is 3 for the PANA-L7-PEN Engine ID. Therefore, the Application ID is encoded as: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 20 | enterprise ID = X ...| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |...Ent.ID.contd| 10000 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format '20..X..10000' is used for simplicity in the examples below. The Exporting Process creates a Template Record with a few Information Elements: amongst other things, the Application ID. For example: - sourceIPv4Address (key field) - destinationIPv4Address (key field) - ipDiffServCodePoint (key field) - applicationId (key field) - octetTotalCount (non-key field) For example, a Flow Record corresponding to the above Template Record may contain: { sourceIPv4Address=192.0.2.1, destinationIPv4Address=192.0.2.2, ipDiffServCodePoint=0, applicationId='20..X..10000', octetTotalCount=123456 } Claise, et al. Informational [Page 21] RFC 6759 Export of App. Info. in IPFIX November 2012 The 10000 value is globally unique for enterprise X, so that the Collector can determine which application is represented by the Application ID by loading the registry out of band. Along with this Flow Record, a new Options Template Record would be exported, as shown in Section 6.8. 6.7. Example: Port Obfuscation For example, an HTTP server might run on a TCP port 23 (assigned to telnet in [IANA-PORTS]). If the Metering Process is capable of detecting HTTP in the same case, the Application ID representation must contain HTTP. However, if the reporting application wants to determine whether or not the default HTTP port 80 or 8080 was used, the transport ports (sourceTransportPort and destinationTransportPort at [IANA-IPFIX]) must also be exported in the corresponding IPFIX record. In the case of a standardized IANA layer 4 port, the Classification Engine ID (PANA-L4) is 3, and the Selector ID has the value of 80 for HTTP (see [IANA-PORTS]). From Table 2 the Selector ID length is 2 for the PANA-L4 Engine ID. Therefore, the Application ID is encoded as: 0 1 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 3 | 80 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The Exporting Process creates a Template Record with a few Information Elements: amongst other things, the Application ID. For example: - sourceIPv4Address (key field) - destinationIPv4Address (key field) - protocol (key field) - destinationTransportPort (key field) - applicationId (key field) - octetTotalCount (non-key field) Claise, et al. Informational [Page 22] RFC 6759 Export of App. Info. in IPFIX November 2012 For example, a Flow Record corresponding to the above Template Record may contain: { sourceIPv4Address=192.0.2.1, destinationIPv4Address=192.0.2.2, protocol=17, destinationTransportPort=23, applicationId='3..80', octetTotalCount=123456 } The Collector has all the required information to determine that the application is HTTP, but runs on port 23. 6.8. Example: Application Name Mapping Options Template Along with the Flow Records shown in the above examples, a new Options Template Record should be exported to express the Application Name and Application Description associated with each Application ID. The Options Template Record contains the following Information Elements: 1. Scope = applicationId. From RFC 5101: The scope, which is only available in the Options Template Set, gives the context of the reported Information Elements in the Data Records. 2. applicationName. 3. applicationDescription. The Options Data Record associated with the examples above would contain, for example: { scope=applicationId='2..90', applicationName="foo", applicationDescription="The foo protocol", scope=applicationId='13..10000', applicationName="webex", applicationDescription="Webex application" } scope=applicationId='20..X..10000', applicationName="webex", applicationDescription="Webex application" } Claise, et al. Informational [Page 23] RFC 6759 Export of App. Info. in IPFIX November 2012 When combined with the example Flow Records above, these Options Template Records tell the Collector: 1. A flow of 123456 bytes exists from sourceIPv4Address 192.0.2.1 to destinationIPv4address 192.0.2.2 with an applicationId of '12..90', which maps to the "foo" application. 2. A flow of 123456 bytes exists from sourceIPv4Address 192.0.2.1 to destinationIPv4address 192.0.2.2 with an Application ID of '13..10000', which maps to the "Webex" application. 3. A flow of 123456 bytes exists from sourceIPv4Address 192.0.2.1 to destinationIPv4address 192.0.2.2 with an Application ID of '20..PEN..10000', which maps to the "Webex" application, according to the application registry from the enterprise X. 6.9. Example: Attributes Values Options Template Record Along with the Flow Records shown in the above examples, a new Options Template Record is exported to express the values of the different attributes related to the Application IDs. The Options Template Record would contain the following Information Elements: 1. Scope = applicationId. From RFC 5101: The scope, which is only available in the Options Template Set, gives the context of the reported Information Elements in the Data Records. 2. applicationCategoryName. 3. applicationSubCategoryName. 4. applicationGroupName 5. p2pTechnology 6. tunnelTechnology 7. encryptedTechnology Claise, et al. Informational [Page 24] RFC 6759 Export of App. Info. in IPFIX November 2012 The Options Data Record associated with the examples above would contain, for example: { scope=applicationId='2..90', applicationCategoryName="foo-category", applicationSubCategoryName="foo-subcategory", applicationGroupName="foo-group", p2pTechnology=NO tunnelTechnology=YES encryptedTechnology=NO When combined with the example Flow Records above, these Options Template Records tell the Collector: A flow of 123456 bytes exists from sourceIPv4Address 192.0.2.1 to destinationIPv4address 192.0.2.2 with a DSCP value of 0 and an applicationId of '12..90', which maps to the "foo" application. This application can be characterized by the relevant attributes values. 7. IANA Considerations 7.1. New Information Elements This document specifies 10 new IPFIX Information Elements: applicationDescription, applicationId, applicationName, classificationEngineId, applicationCategoryName, applicationSubCategoryName, applicationGroupName, p2pTechnology, tunnelTechnology, and encryptedTechnology. The new Information Elements listed below have been added to the IPFIX Information Element registry at [IANA-IPFIX]. 7.1.1. applicationDescription Name: applicationDescription Description: Specifies the description of an application. Abstract Data Type: string Data Type Semantics: ElementId: 94 Status: current Claise, et al. Informational [Page 25] RFC 6759 Export of App. Info. in IPFIX November 2012 7.1.2. applicationId Name: applicationId Description: Specifies an Application ID. Abstract Data Type: octetArray Data Type Semantics: identifier Reference: See Section 4 of [RFC6759] for the applicationId Information Element Specification. ElementId: 95 Status: current 7.1.3. applicationName Name: applicationName Description: Specifies the name of an application. Abstract Data Type: string Data Type Semantics: ElementId: 96 Status: current 7.1.4. classificationEngineId Name: classificationEngineId Description: A unique identifier for the engine that determined the Selector ID. Thus, the Classification Engine ID defines the context for the Selector ID. The Classification Engine can be considered as a specific registry for application assignments. Initial values for this field are listed below. Further values may be assigned by IANA in the Classification Engine IDs registry per Section 7.2. 0 Invalid. 1 IANA-L3: The Assigned Internet Protocol Number (layer 3 (L3)) is exported in the Selector ID. See http://www.iana.org/assignments/protocol-numbers. 2 PANA-L3: Proprietary layer 3 definition. An enterprise can export its own layer 3 protocol numbers. The Selector ID has a global significance for all devices from the same enterprise. Claise, et al. Informational [Page 26] RFC 6759 Export of App. Info. in IPFIX November 2012 3 IANA-L4: The IANA layer 4 (L4) well-known port number is exported in the Selector ID. See [IANA-PORTS]. Note: as an IPFIX flow is unidirectional, it contains the destination port. 4 PANA-L4: Proprietary layer 4 definition. An enterprise can export its own layer 4 port numbers. The Selector ID has global significance for devices from the same enterprise. Example: IPFIX was pre-assigned port 4739 using the IANA early allocation process [RFC4020] years before the document was published as an RFC. While waiting for the RFC and it associated IANA registration, Selector ID 4739 was used with this PANA-L4. 5 Reserved 6 USER-Defined: The Selector ID represents applications defined by the user (using CLI, GUI, etc.) based on the methods described in Section 2. The Selector ID has a local significance per device. 7 Reserved 8 Reserved 9 Reserved 10 Reserved 11 Reserved 12 PANA-L2: Proprietary layer 2 (L2) definition. An enterprise can export its own layer 2 identifiers. The Selector ID represents the enterprise's unique global layer 2 applications. The Selector ID has a global significance for all devices from the same enterprise. Examples include the Cisco Subnetwork Access Protocol (SNAP). Claise, et al. Informational [Page 27] RFC 6759 Export of App. Info. in IPFIX November 2012 13 PANA-L7: Proprietary layer 7 definition. The Selector ID represents the enterprise's unique global ID for layer 7 applications. The Selector ID has a global significance for all devices from the same enterprise. This Classification Engine ID is used when the application registry is owned by the Exporter manufacturer (referred to as the "enterprise" in this document). 14 Reserved 15 Reserved 16 Reserved 17 Reserved 18 ETHERTYPE: The Selector ID represents the well- known Ethertype. See [ETHERTYPE]. 19 LLC: The Selector ID represents the well-known IEEE 802.2 Link Layer Control (LLC) Destination Service Access Point (DSAP). See [LLC]. 20 PANA-L7-PEN: Proprietary layer 7 definition, including a Private Enterprise Number (PEN) [IANA-PEN] to identify that the application registry being used is not owned by the Exporter manufacturer or to identify the original enterprise in the case of a mediator or 3rd party device. The Selector ID represents the enterprise unique global ID for layer 7 applications. The Selector ID has a global significance for all devices from the same enterprise. Some values (5, 7, 8, 9, 10, 11, 14, 15, 16, and 17), are reserved to be compliant with existing implementations already using the classificationEngineId. Abstract Data Type: unsigned8 Data Type Semantics: identifier ElementId: 101 Status: current Claise, et al. Informational [Page 28] RFC 6759 Export of App. Info. in IPFIX November 2012 7.1.5. applicationCategoryName Name: applicationCategoryName Description: An attribute that provides a first-level categorization for each Application Id. Abstract Data Type: string Data Type Semantics: ElementId: 372 Status: current 7.1.6. applicationSubCategoryName Name: applicationSubCategoryName Description: An attribute that provides a second-level categorization for each Application Id. Abstract Data Type: string Data Type Semantics: ElementId: 373 Status: current 7.1.7. applicationGroupName Name: applicationGroupName Description: An attribute that groups multiple Application IDs that belong to the same networking application. Abstract Data Type: string Data Type Semantics: ElementId: 374 Status: current 7.1.8. p2pTechnology Name: p2pTechnology Description: Specifies if the Application ID is based on peer-to-peer technology. Possible values are { "yes", "y", 1 }, { "no", "n", 2 }, and { "unassigned", "u", 0 }. Abstract Data Type: string Data Type Semantics: ElementId: 288 Status: current Claise, et al. Informational [Page 29] RFC 6759 Export of App. Info. in IPFIX November 2012 7.1.9. tunnelTechnology Name: tunnelTechnology Description: Specifies if the Application ID is used as a tunnel technology. Possible values are { "yes", "y", 1 }, { "no", "n", 2 }, and { "unassigned", "u", 0 }. Abstract Data Type: string Data Type Semantics: ElementId: 289 Status: current 7.1.10. encryptedTechnology Name: encryptedTechnology Description: Specifies if the Application ID is an encrypted networking protocol. Possible values are { "yes", "y", 1 }, { "no", "n", 2 }, and { "unassigned", "u", 0 }. Abstract Data Type: string Data Type Semantics: ElementId: 290 Status: current 7.2. Classification Engine ID Registry The Information Element #101, named classificationEngineId, carries information about the context for the Selector ID, and can be considered as a specific registry for application assignments. For ensuring extensibility of this information, IANA has created a new registry for Classification Engine IDs and filled it with the initial list from the description Information Element #101, classificationEngineId, along with their respective default lengths (Table 2 in this document). New assignments for Classification Engine IDs will be administered by IANA through Expert Review [RFC5226], i.e., review by one of a group of experts designated by an IETF Area Director. The group of experts must double-check the new definitions with already defined Classification Engine IDs for completeness, accuracy, and redundancy. The specification of Classification Engine IDs MUST be published using a well-established and persistent publication medium. 8. Security Considerations The same security considerations as for the IPFIX protocol [RFC5101] apply. The IPFIX extension specified in this memo allows to identify what applications are used on the network. Consequently, it is Claise, et al. Informational [Page 30] RFC 6759 Export of App. Info. in IPFIX November 2012 possible to identify what applications are being used by the users, potentially threatening the privacy of those users, if not handled with great care. As mentioned in Section 1.1, the application knowledge is useful in security based applications. Security applications may impose supplementary requirements on the export of application information, and these need to be examined on a case by case basis. 9. References 9.1. Normative References [ETHERTYPE] IEEE, . [IANA-PEN] IANA, "PRIVATE ENTERPRISE NUMBERS", . [IANA-PORTS] IANA, "Service Name and Transport Protocol Port Number Registry", . [IANA-PROTO] IANA, "Protocol Numbers", . [LLC] IEEE, "LOGICAL LINK CONTROL (LLC) PUBLIC LISTING", . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC5101] Claise, B., Ed., "Specification of the IP Flow Information Export (IPFIX) Protocol for the Exchange of IP Traffic Flow Information", RFC 5101, January 2008. [RFC5102] Quittek, J., Bryant, S., Claise, B., Aitken, P., and J. Meyer, "Information Model for IP Flow Information Export", RFC 5102, January 2008. [RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 5226, May 2008. Claise, et al. Informational [Page 31] RFC 6759 Export of App. Info. in IPFIX November 2012 9.2. Informative References [CISCO-APPLICATION-REGISTRY] Cisco, "Application Registry", . [IANA-IPFIX] IANA, "IP Flow Information Export (IPFIX) Entities", . [LLDP] IEEE, Std 802.1AB-2005, "Standard for Local and metropolitan area networks - Station and Media Access Control Connectivity Discovery", IEEE Std 802.1AB-2005 IEEE Std, 2005. [RFC792] Postel, J., "Internet Control Message Protocol", STD 5, RFC 792, September 1981. [RFC3917] Quittek, J., Zseby, T., Claise, B., and S. Zander, "Requirements for IP Flow Information Export (IPFIX)", RFC 3917, October 2004. [RFC3954] Claise, B., Ed., "Cisco Systems NetFlow Services Export Version 9", RFC 3954, October 2004. [RFC4020] Kompella, K. and A. Zinin, "Early IANA Allocation of Standards Track Code Points", BCP 100, RFC 4020, February 2005. [RFC5103] Trammell, B. and E. Boschi, "Bidirectional Flow Export Using IP Flow Information Export (IPFIX)", RFC 5103, January 2008. [RFC5470] Sadasivan, G., Brownlee, N., Claise, B., and J. Quittek, "Architecture for IP Flow Information Export", RFC 5470, March 2009. [RFC5471] Schmoll, C., Aitken, P., and B. Claise, "Guidelines for IP Flow Information Export (IPFIX) Testing", RFC 5471, March 2009. [RFC5473] Boschi, E., Mark, L., and B. Claise, "Reducing Redundancy in IP Flow Information Export (IPFIX) and Packet Sampling (PSAMP) Reports", RFC 5473, March 2009. [RFC5476] Claise, B., Ed., Johnson, A., and J. Quittek, "Packet Sampling (PSAMP) Protocol Specifications", RFC 5476, March 2009. Claise, et al. Informational [Page 32] RFC 6759 Export of App. Info. in IPFIX November 2012 [RFC5477] Dietz, T., Claise, B., Aitken, P., Dressler, F., and G. Carle, "Information Model for Packet Sampling Exports", RFC 5477, March 2009. [RFC5353] Xie, Q., Stewart, R., Stillman, M., Tuexen, M., and A. Silverton, "Endpoint Handlespace Redundancy Protocol (ENRP)", RFC 5353, September 2008. [RFC5811] Hadi Salim, J. and K. Ogawa, "SCTP-Based Transport Mapping Layer (TML) for the Forwarding and Control Element Separation (ForCES) Protocol", RFC 5811, March 2010. [RFC6183] Kobayashi, A., Claise, B., Muenz, G., and K. Ishibashi, "IP Flow Information Export (IPFIX) Mediation: Framework", RFC 6183, April 2011. [RFC6313] Claise, B., Dhandapani, G., Aitken, P., and S. Yates, "Export of Structured Data in IP Flow Information Export (IPFIX)", RFC 6313, July 2011. 10. Acknowledgements The authors would like to thank their many colleagues across Cisco Systems who made this work possible. Specifically, Patrick Wildi for his time and expertise. Claise, et al. Informational [Page 33] RFC 6759 Export of App. Info. in IPFIX November 2012 Appendix A. Additions to XML Specification of IPFIX Information Elements (Non-normative) This appendix contains additions to the machine-readable description of the IPFIX information model coded in XML in Appendix A and Appendix B in [RFC5102]. Note that this appendix is of informational nature, while the text in Section 7 (generated from this appendix) is normative. The following field definitions are appended to the IPFIX information model in Appendix A of [RFC5102]. Specifies the description of an application. Specifies an Application ID. See Section 4 of [RFC6759] for the applicationId Information Element Specification. Specifies the name of an application. 0 Invalid. 1 IANA-L3: The Assigned Internet Protocol Number (layer 3 (L3)) is exported in the Selector ID. See http://www.iana.org/assignments/protocol- numbers. 2 PANA-L3: Proprietary layer 3 definition. An enterprise can export its own layer 3 protocol numbers. The Selector ID has a global significance for all devices from the same enterprise. 3 IANA-L4: The IANA layer 4 (L4) well-known port number is exported in the Selector ID. See [IANA-PORTS]. Note: as an IPFIX flow is unidirectional, it contains the destination port. 4 PANA-L4: Proprietary layer 4 definition. An enterprise can export its own layer 4 port numbers. The Selector ID has global significance for devices from the same enterprise. Example: IPFIX was pre-assigned port 4739 using the IANA early allocation process [RFC4020] years before the document was published as an RFC. While waiting for the RFC and its associated IANA registration, Selector ID 4739 was used with this PANA-L4. 5 Reserved Claise, et al. Informational [Page 35] RFC 6759 Export of App. Info. in IPFIX November 2012 6 USER-Defined: The Selector ID represents applications defined by the user (using CLI, GUI, etc.) based on the methods described in Section 2. The Selector ID has a local significance per device. 7 Reserved 8 Reserved 9 Reserved 10 Reserved 11 Reserved 12 PANA-L2: Proprietary layer 2 (L2) definition. An enterprise can export its own layer 2 identifiers. The Selector ID represents the enterprise's unique global layer 2 applications. The Selector ID has a global significance for all devices from the same enterprise. Examples include the Cisco Subnetwork Access Protocol (SNAP). 13 PANA-L7: Proprietary layer 7 definition. The Selector ID represents the enterprise's unique global ID for layer 7 applications. The Selector ID has a global significance for all devices from the same enterprise. This Classification Engine ID is used when the application registry is owned by the Exporter manufacturer (referred to as the "enterprise" in this document). 14 Reserved 15 Reserved 16 Reserved 17 Reserved 18 ETHERTYPE: The Selector ID represents the well-known Ethertype. See [ETHERTYPE]. 19 LLC: The Selector ID represents the well-known IEEE 802.2 Link Layer Control (LLC) Claise, et al. Informational [Page 36] RFC 6759 Export of App. Info. in IPFIX November 2012 Destination Service Access Point (DSAP). See [LLC]. 20 PANA-L7-PEN: Proprietary layer 7 definition, including a Private Enterprise Number (PEN) [IANA-PEN] to identify that the application registry being used is not owned by the Exporter manufacturer or to identify the original enterprise in the case of a mediator or 3rd party device. The Selector ID represents the enterprise unique global ID for layer 7 applications. The Selector ID has a global significance for all devices from the same enterprise. An attribute that provides a first-level categorization for each Application Id. An attribute that provides a second-level categorization for each Application ID. An attribute that groups multiple Application IDs that belong to the same networking application. Specifies if the Application ID is based on peer- to-peer technology. Possible values are { "yes", "y", 1 }, { "no", "n", 2 }, and { "unassigned", "u", 0 }. Specifies if the Application ID is used as a tunnel technology. Possible values are { "yes", "y", 1 }, { "no", "n", 2 }, and { "unassigned", "u", 0 }. Specifies if the Application ID is an encrypted networking protocol. Possible values are { "yes", "y", 1 }, { "no", "n", 2 }, and { "unassigned", "u", 0 }. Appendix B. Port Collisions Tables (Non-normative) The following table lists the 10 ports that have different protocols assigned for TCP and UDP (at the time of writing this document): exec 512/tcp remote process execution; authentication performed using passwords and UNIX login names comsat/biff 512/udp used by mail system to notify users of new mail received; currently receives messages only from processes on the same machine login 513/tcp remote login a la telnet; automatic authentication performed based on priviledged [sic] port numbers and distributed data bases which identify "authentication domains" who 513/udp maintains data bases showing who's logged in to machines on a local net and the load average of the machine shell 514/tcp cmd like exec, but automatic authentication is performed as for login server Claise, et al. Informational [Page 39] RFC 6759 Export of App. Info. in IPFIX November 2012 syslog 514/udp oob-ws-https 664/tcp DMTF out-of-band secure web services management protocol Jim Davis asf-secure-rmcp 664/udp ASF Secure Remote Management and Control Protocol rfile 750/tcp kerberos-iv 750/udp kerberos version iv submit 773/tcp notify 773/udp rpasswd 774/tcp acmaint_dbd 774/udp entomb 775/tcp acmaint_transd 775/udp busboy 998/tcp puparp 998/udp garcon 999/tcp applix 999/udp Applix ac Table 4: Different Protocols on UDP and TCP The following table lists the 19 ports that have different protocols assigned for TCP and SCTP (at the time of writing this document): # 3097/tcp Reserved itu-bicc-stc 3097/sctp ITU-T Q.1902.1/Q.2150.3 Greg Sidebottom # 5090/tcp car 5090/sctp Candidate AR # 5091/tcp cxtp 5091/sctp Context Transfer Protocol Claise, et al. Informational [Page 40] RFC 6759 Export of App. Info. in IPFIX November 2012 # 6704/tcp Reserved frc-hp 6704/sctp ForCES HP (High Priority) channel [RFC5811] # 6705/tcp Reserved frc-mp 6705/sctp ForCES MP (Medium Priority) channel [RFC5811] # 6706/tcp Reserved frc-lp 6706/sctp ForCES LP (Low Priority) channel [RFC5811] # 9082/tcp lcs-ap 9082/sctp LCS Application Protocol Kimmo Kymalainen # 9902/tcp enrp-sctp-tls 9902/sctp enrp/tls server channel [RFC5353] # 11997/tcp # 11998/tcp # 11999/tcp wmereceiving 11997/sctp WorldMailExpress wmedistribution 11998/sctp WorldMailExpress wmereporting 11999/sctp WorldMailExpress Greg Foutz # 25471/tcp rna 25471/sctp RNSAP User Adaptation for Iurh Dario S. Tonesi 07 February 2011 # 29118/tcp Reserved sgsap 29118/sctp SGsAP in 3GPP Claise, et al. Informational [Page 41] RFC 6759 Export of App. Info. in IPFIX November 2012 # 29168/tcp Reserved sbcap 29168/sctp SBcAP in 3GPP # 29169/tcp iuhsctpassoc 29169/sctp HNBAP and RUA Common Association John Meredith 08 September 2009 # 36412/tcp s1-control 36412/sctp S1-Control Plane (3GPP) Kimmo Kymalainen 01 September 2009 # 36422/tcp x2-control 36422/sctp X2-Control Plane (3GPP) Kimmo Kymalainen 01 September 2009 # 36443/tcp m2ap 36443/sctp M2 Application Part Dario S. Tonesi 07 February 2011 # 36444/tcp m3ap 36444/sctp M3 Application Part Dario S. Tonesi 07 February 2011 Table 5: Different Protocols on SCTP and TCP Appendix C. Application Registry Example (Non-normative) A reference to the Cisco Systems assigned numbers for the Application ID and the different attribute assignments can be found at [CISCO-APPLICATION-REGISTRY]. Claise, et al. Informational [Page 42] RFC 6759 Export of App. Info. in IPFIX November 2012 Authors' Addresses Benoit Claise Cisco Systems, Inc. De Kleetlaan 6a b1 Diegem 1813 Belgium Phone: +32 2 704 5622 EMail: bclaise@cisco.com Paul Aitken Cisco Systems, Inc. 96 Commercial Quay Commercial Street Edinburgh, EH6 6LX United Kingdom Phone: +44 131 561 3616 EMail: paitken@cisco.com Nir Ben-Dvora Cisco Systems, Inc. 32 HaMelacha St., P.O. Box 8735, I.Z.Sapir South Netanya, 42504 Israel Phone: +972 9 892 7187 EMail: nirbd@cisco.com Claise, et al. Informational [Page 43]