Internet Engineering Task Force (IETF) N. Duffield Request for Comments: 6534 AT&T Labs-Research Category: Standards Track A. Morton ISSN: 2070-1721 AT&T Labs J. Sommers Colgate University May 2012 Loss Episode Metrics for IP Performance Metrics (IPPM) Abstract The IETF has developed a one-way packet loss metric that measures the loss rate on a Poisson and Periodic probe streams between two hosts. However, the impact of packet loss on applications is, in general, sensitive not just to the average loss rate but also to the way in which packet losses are distributed in loss episodes (i.e., maximal sets of consecutively lost probe packets). This document defines one-way packet loss episode metrics, specifically, the frequency and average duration of loss episodes and a probing methodology under which the loss episode metrics are to be measured. Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc6534. Copyright Notice Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must Duffield, et al. Standards Track [Page 1] RFC 6534 Loss Episode Metrics for IPPM May 2012 include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English. Table of Contents 1. Introduction ....................................................4 1.1. Background and Motivation ..................................4 1.1.1. Requirements Language ...............................5 1.2. Loss Episode Metrics and Bi-Packet Probes ..................5 1.3. Outline and Contents .......................................6 2. Singleton Definition for Type-P-One-way Bi-Packet Loss ..........7 2.1. Metric Name ................................................7 2.2. Metric Parameters ..........................................7 2.3. Metric Units ...............................................7 2.4. Metric Definition ..........................................7 2.5. Discussion .................................................8 2.6. Methodologies ..............................................8 2.7. Errors and Uncertainties ...................................8 2.8. Reporting the Metric .......................................8 3. General Definition of Samples for Type-P-One-way-Bi-Packet-Loss ...................................8 3.1. Metric Name ................................................9 3.2. Metric Parameters ..........................................9 3.3. Metric Units ...............................................9 3.4. Metric Definition ..........................................9 3.5. Discussion .................................................9 3.6. Methodologies .............................................10 3.7. Errors and Uncertainties ..................................10 3.8. Reporting the Metric ......................................10 4. An Active Probing Methodology for Bi-Packet Loss ...............10 4.1. Metric Name ...............................................10 4.2. Metric Parameters .........................................10 4.3. Metric Units ..............................................11 4.4. Metric Definition .........................................11 4.5. Discussion ................................................11 Duffield, et al. Standards Track [Page 2] RFC 6534 Loss Episode Metrics for IPPM May 2012 4.6. Methodologies .............................................11 4.7. Errors and Uncertainties ..................................12 4.8. Reporting the Metric ......................................12 5. Loss Episode Proto-Metrics .....................................12 5.1. Loss-Pair-Counts ..........................................13 5.2. Bi-Packet-Loss-Ratio ......................................13 5.3. Bi-Packet-Loss-Episode-Duration-Number ....................13 5.4. Bi-Packet-Loss-Episode-Frequency-Number ...................13 6. Loss Episode Metrics Derived from Bi-Packet Loss Probing .......14 6.1. Geometric Stream: Loss Ratio ..............................14 6.1.1. Metric Name ........................................14 6.1.2. Metric Parameters ..................................14 6.1.3. Metric Units .......................................15 6.1.4. Metric Definition ..................................15 6.1.5. Discussion .........................................15 6.1.6. Methodologies ......................................15 6.1.7. Errors and Uncertainties ...........................15 6.1.8. Reporting the Metric ...............................15 6.2. Geometric Stream: Loss Episode Duration ...................16 6.2.1. Metric Name ........................................16 6.2.2. Metric Parameters ..................................16 6.2.3. Metric Units .......................................16 6.2.4. Metric Definition ..................................16 6.2.5. Discussion .........................................16 6.2.6. Methodologies ......................................16 6.2.7. Errors and Uncertainties ...........................17 6.2.8. Reporting the Metric ...............................17 6.3. Geometric Stream: Loss Episode Frequency ..................17 6.3.1. Metric Name ........................................17 6.3.2. Metric Parameters ..................................17 6.3.3. Metric Units .......................................17 6.3.4. Metric Definition ..................................18 6.3.5. Discussion .........................................18 6.3.6. Methodologies ......................................18 6.3.7. Errors and Uncertainties ...........................18 6.3.8. Reporting the Metric ...............................18 7. Applicability of Loss Episode Metrics ..........................18 7.1. Relation to Gilbert Model .................................18 8. Security Considerations ........................................19 9. References .....................................................20 9.1. Normative References ......................................20 9.2. Informative References ....................................20 Duffield, et al. Standards Track [Page 3] RFC 6534 Loss Episode Metrics for IPPM May 2012 1. Introduction 1.1. Background and Motivation Packet loss in the Internet is a complex phenomenon due to the bursty nature of traffic and congestion processes, influenced by both end- users and applications and the operation of transport protocols such as TCP. For these reasons, the simplest model of packet loss -- the single parameter Bernoulli (independent) loss model -- does not represent the complexity of packet loss over periods of time. Correspondingly, a single loss metric -- the average packet loss ratio over some period of time -- arising, e.g., from a stream of Poisson probes as in [RFC2680] is not sufficient to determine the effect of packet loss on traffic in general. Moving beyond single parameter loss models, Markovian and Markov- modulated loss models involving transitions between a good and bad state, each with an associated loss rate, have been proposed by Gilbert [Gilbert] and more generally by Elliot [Elliot]. In principle, Markovian models can be formulated over state spaces involving patterns of loss of any desired number of packets. However, further increase in the size of the state space makes such models cumbersome both for parameter estimation (accuracy decreases) and prediction in practice (due to computational complexity and sensitivity to parameter inaccuracy). In general, the relevance and importance of particular models can change in time, e.g., in response to the advent of new applications and services. For this reason, we are drawn to empirical metrics that do not depend on a particular model for their interpretation. An empirical measure of packet loss complexity, the index of dispersion of counts (IDC), comprise, for each t >0, the ratio v(t) / a(t) of the variance v(t) and average a(t) of the number of losses over successive measurement windows of a duration t. However, a full characterization of packet loss over time requires specification of the IDC for each window size t>0. In the standards arena, loss pattern sample metrics are defined in [RFC3357]. Following the Gilbert-Elliot model, burst metrics specific for Voice over IP (VoIP) that characterize complete episodes of lost, transmitted, and discarded packets are defined in [RFC3611]. The above considerations motivate the formulation of empirical metrics of one-way packet loss that provide the simplest generalization of [RFC2680] (which is widely adopted but only defines a single loss-to-total ratio metric). The metrics defined here Duffield, et al. Standards Track [Page 4] RFC 6534 Loss Episode Metrics for IPPM May 2012 capture deviations from independent packet loss in a robust model- independent manner. The document also defines efficient measurement methodologies for these metrics. 1.1.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 1.2. Loss Episode Metrics and Bi-Packet Probes The losses experienced by the packet stream can be viewed as occurring in loss episodes, i.e., a maximal set of consecutively lost packets. This memo describes one-way loss episode metrics: their frequency and average duration. Although the average loss ratio can be expressed in terms of these quantities, they go further in characterizing the statistics of the patterns of packet loss within the stream of probes. This is useful information in understanding the effect of packet losses on application performance, since different applications can have different sensitivities to patterns of loss, being sensitive not only to the long-term average loss rate, but how losses are distributed in time. As an example, MPEG video traffic may be sensitive to loss involving the I-frame in a group of pictures, but further losses within an episode of sufficiently short duration have no further impact; the damage is already done. The loss episode metrics presented here have the following useful properties: 1. the metrics are empirical and do not depend on an underlying model; e.g., the loss process is not assumed to be Markovian. On the other hand, it turns out that the metrics of this memo can be related to the special case of the Gilbert Model parameters; see Section 7. 2. the metric units can be directly compared with applications or user requirements or tolerance for network loss performance, in the frequency and duration of loss episodes, as well as the usual packet loss ratio, which can be recovered from the loss episode metrics upon dividing the average loss episode duration by the loss episode frequency. 3. the metrics provide the smallest possible increment in complexity beyond, but in the spirit of, the IP Performance Metrics (IPPM) average packet loss ratio metrics [RFC2680], i.e., moving from a single metric (average packet loss ratio) to a pair of metrics (loss episode frequency and average loss episode duration). Duffield, et al. Standards Track [Page 5] RFC 6534 Loss Episode Metrics for IPPM May 2012 The document also describes a probing methodology under which loss episode metrics are to be measured. The methodology comprises sending probe packets in pairs, where packets within each probe pair have a fixed separation, and the time between pairs takes the form of a geometric distributed number multiplied by the same separation. This can be regarded a generalization of Poisson probing where the probes are pairs rather than single packets as in [RFC2680], and also of geometric probing described in [RFC2330]. However, it should be distinguished from back-to-back packet pairs whose change in separation on traversing a link is used to probe bandwidth. In this document, the separation between the packets in a pair is the temporal resolution at which different loss episodes are to be distinguished. The methodology does not measure episodes of loss of consecutive background packets on the measured path. One key feature of this methodology is its efficiency: it estimates the average length of loss episodes without directly measuring the complete episodes themselves. Instead, this information is encoded in the observed relative frequencies of the four possible outcomes arising from the loss or successful transmission of each of the two packets of the probe pairs. This is distinct from the approach of [RFC3611], which reports on directly measured episodes. The metrics defined in this memo are "derived metrics", according to Section 6.1 of [RFC2330] (the IPPM framework). They are based on the singleton loss metric defined in Section 2 of [RFC2680] . 1.3. Outline and Contents o Section 2 defines the fundamental singleton metric for the possible outcomes of a probe pair: Type-P-One-way-Bi-Packet-Loss. o Section 3 defines sample sets of this metric derived from a general probe stream: Type-P-One-way-Bi-Packet-Loss-Stream. o Section 4 defines the prime example of the Bi-Packet-Loss-Stream metrics, specifically Type-P-One-way-Bi-Packet-Loss-Geometric- Stream arising from the geometric stream of packet-pair probes that was described informally in Section 1. o Section 5 defines loss episode proto-metrics that summarize the outcomes from a stream metrics as an intermediate step to forming the loss episode metrics; they need not be reported in general. o Section 6 defines the final loss episode metrics that are the focus of this memo, the new metrics: * Type-P-One-way-Bi-Packet-Loss-Geometric-Stream-Episode- Duration, the average duration, in seconds, of a loss episode. Duffield, et al. Standards Track [Page 6] RFC 6534 Loss Episode Metrics for IPPM May 2012 * Type-P-One-way-Bi-Packet-Loss-Geometric-Stream-Episode- Frequency, the average frequency, per second, at which loss episodes start. * Type-P-One-way-Bi-Packet-Loss-Geometric-Stream-Ratio, which is the average packet loss ratio metric arising from the geometric stream probing methodology o Section 7 details applications and relations to existing loss models. 2. Singleton Definition for Type-P-One-way Bi-Packet Loss 2.1. Metric Name Type-P-One-way-Bi-Packet-Loss 2.2. Metric Parameters o Src, the IP address of a source host o Dst, the IP address of a destination host o T1, a sending time of the first packet o T2, a sending time of the second packet, with T2>T1 o F, a selection function defining unambiguously the two packets from the stream selected for the metric o P, the specification of the packet type, over and above the source and destination addresses 2.3. Metric Units A Loss Pair is pair (l1, l2) where each of l1 and l2 is a binary value 0 or 1, where 0 signifies successful transmission of a packet and 1 signifies loss. The metric unit of Type-P-One-way-Bi-Packet-Loss is a Loss Pair. 2.4. Metric Definition 1. "The Type-P-One-way-Bi-Packet-Loss with parameters (Src, Dst, T1, T2, F, P) is (1,1)" means that Src sent the first bit of a Type-P packet to Dst at wire-time T1 and the first bit of a Type-P packet to Dst at wire-time T2>T1 and that neither packet was received at Dst. Duffield, et al. Standards Track [Page 7] RFC 6534 Loss Episode Metrics for IPPM May 2012 2. "The Type-P-One-way-Bi-Packet-Loss with parameters (Src, Dst, T1, T2, F, P) is (1,0)" means that Src sent the first bit of a Type-P packet to Dst at wire-time T1 and the first bit of a Type-P packet to Dst at wire-time T2>T1 and that the first packet was not received at Dst, and the second packet was received at Dst 3. "The Type-P-One-way-Bi-Packet-Loss with parameters (Src, Dst, T1, T2, F, P) is (0,1)" means that Src sent the first bit of a Type-P packet to Dst at wire-time T1 and the first bit of a Type-P packet to Dst at wire-time T2>T1 and that the first packet was received at Dst, and the second packet was not received at Dst 4. "The Type-P-One-way-Bi-Packet-Loss with parameters (Src, Dst, T1, T2, F, P) is (0,0)" means that Src sent the first bit of a Type-P packet to Dst at wire-time T1 and the first bit of a Type-P packet to Dst at wire-time T2>T1 and that both packets were received at Dst. 2.5. Discussion The purpose of the selection function is to specify exactly which packets are to be used for measurement. The notion is taken from Section 2.5 of [RFC3393], where examples are discussed. 2.6. Methodologies The methodologies related to the Type-P-One-way-Packet-Loss metric in Section 2.6 of [RFC2680] are similar for the Type-P-One-way-Bi- Packet-Loss metric described above. In particular, the methodologies described in RFC 2680 apply to both packets of the pair. 2.7. Errors and Uncertainties Sources of error for the Type-P-One-way-Packet-Loss metric in Section 2.7 of [RFC2680] apply to each packet of the pair for the Type-P-One- way-Bi-Packet-Loss metric. 2.8. Reporting the Metric Refer to Section 2.8 of [RFC2680]. 3. General Definition of Samples for Type-P-One-way-Bi-Packet-Loss Given the singleton metric for Type-P-One-way-Bi-Packet-Loss, we now define examples of samples of singletons. The basic idea is as follows. We first specify a set of times T1 < T2 <... 0 o 0 if N(0,1) + N(1,0) + N(1,1) = 0 (no probe packets lost) o Undefined if N(0,1) + N(1,0) + N(0,0) = 0 (all probe packets lost) Note N(0,1) + N(1,0) is zero if there are no transitions between loss and no-loss outcomes. 5.4. Bi-Packet-Loss-Episode-Frequency-Number The Bi-Packet-Loss-Episode-Frequency-Number associated with a set of n Loss Pairs L1,,,,Ln is defined in terms of their Loss-Pair-Counts as Bi-Packet-Loss-Ratio / Bi-Packet-Loss-Episode-Duration-Number, when this can be defined, specifically, it is as follows: o (N(1,0) + N(1,1)) * (N(0,1) + N(1,0)) / (2*N(1,1) + N(0,1) + N(1,0) ) / n if N(0,1) + N(1,0) > 0 o 0 if N(0,1) + N(1,0) + N(1,1) = 0 (no probe packets lost) o 1 if N(0,1) + N(1,0) + N(0,0) = 0 (all probe packets lost) Duffield, et al. Standards Track [Page 13] RFC 6534 Loss Episode Metrics for IPPM May 2012 6. Loss Episode Metrics Derived from Bi-Packet Loss Probing Metrics for the time frequency and time duration of loss episodes are now defined as functions of the set of n Loss Pairs L1,....,Ln. Although a loss episode is defined as a maximal set of successive lost packets, the loss episode metrics are not defined directly in terms of the sequential patterns of packet loss exhibited by Loss Pairs. This is because samples, including Type-P-One-way-Bi-Packet- Loss-Geometric-Stream, generally do not report all lost packets in each episode. Instead, the metrics are defined as functions of the Loss-Pair-Counts of the sample, for reasons that are now described. Consider an idealized Type-P-One-way-Bi-Packet-Loss-Geometric-Stream sample in which the launch probability q =1. It is shown in [SBDR08] that the average number of packets in a loss episode of this ideal sample is exactly the Bi-Packet-Loss-Episode-Duration derived from its set of Loss Pairs. Note this computation makes no reference to the position of lost packet in the sequence of probes. A general Type-P-One-way-Bi-Packet-Loss-Geometric-Stream sample with launch probability q < 1, independently samples, with probability q, each Loss Pair of an idealized sample. On average, the Loss-Pair- Counts (if normalized by the total number of pairs) will be the same as in the idealized sample. The loss episode metrics in the general case are thus estimators of those for the idealized case; the statistical properties of this estimation, including a derivation of the estimation variance, is provided in [SBDR08]. 6.1. Geometric Stream: Loss Ratio 6.1.1. Metric Name Type-P-One-way-Bi-Packet-Loss-Geometric-Stream-Ratio 6.1.2. Metric Parameters o Src, the IP address of a source host o Dst, the IP address of a destination host o T0, the randomly selected starting time [RFC3432] for periodic launch opportunities o d, the time spacing between potential launch times, Ti and T(i+1) o n, a count of potential measurement instants Duffield, et al. Standards Track [Page 14] RFC 6534 Loss Episode Metrics for IPPM May 2012 o q, a launch probability o F, a selection function defining unambiguously the two packets from the stream selected for the metric o P, the specification of the packet type, over and above the source and destination address 6.1.3. Metric Units A decimal number in the interval [0,1] 6.1.4. Metric Definition The result obtained by computing the Bi-Packet-Loss-Ratio over a Type-P-One-way-Bi-Packet-Loss-Geometric-Stream sample with the metric parameters. 6.1.5. Discussion Type-P-One-way-Bi-Packet-Loss-Geometric-Stream-Ratio estimates the fraction of packets lost from the geometric stream of Bi-Packet probes. 6.1.6. Methodologies Refer to Section 4.6. 6.1.7. Errors and Uncertainties Because Type-P-One-way-Bi-Packet-Loss-Geometric-Stream is sampled in general (when the launch probability q <1), the metrics described in this section can be regarded as statistical estimators of the corresponding idealized version corresponding to q = 1. Estimation variance as it applies to Type-P-One-way-Bi-Packet-Loss-Geometric- Stream-Loss-Ratio is described in [SBDR08]. For other issues, refer to Section 4.7 6.1.8. Reporting the Metric Refer to Section 4.8. Duffield, et al. Standards Track [Page 15] RFC 6534 Loss Episode Metrics for IPPM May 2012 6.2. Geometric Stream: Loss Episode Duration 6.2.1. Metric Name Type-P-One-way-Bi-Packet-Loss-Geometric-Stream-Episode-Duration 6.2.2. Metric Parameters o Src, the IP address of a source host o Dst, the IP address of a destination host o T0, the randomly selected starting time [RFC3432] for periodic launch opportunities o d, the time spacing between potential launch times, Ti and T(i+1) o n, a count of potential measurement instants o q, a launch probability o F, a selection function defining unambiguously the two packets from the stream selected for the metric o P, the specification of the packet type, over and above the source and destination address 6.2.3. Metric Units A non-negative number of seconds 6.2.4. Metric Definition The result obtained by computing the Bi-Packet-Loss-Episode-Duration- Number over a Type-P-One-way-Bi-Packet-Loss-Geometric-Stream sample with the metric parameters, then multiplying the result by the launch spacing parameter d. 6.2.5. Discussion Type-P-One-way-Bi-Packet-Loss-Geometric-Stream-Episode-Duration estimates the average duration of a loss episode, measured in seconds. The duration measured in packets is obtained by dividing the metric value by the packet launch spacing parameter d. 6.2.6. Methodologies Refer to Section 4.6. Duffield, et al. Standards Track [Page 16] RFC 6534 Loss Episode Metrics for IPPM May 2012 6.2.7. Errors and Uncertainties Because Type-P-One-way-Bi-Packet-Loss-Geometric-Stream is sampled in general (when the launch probability q <1), the metrics described in this section can be regarded as statistical estimators of the corresponding idealized version corresponding to q = 1. Estimation variance as it applies to Type-P-One-way-Bi-Packet-Loss-Geometric- Stream-Episode-Duration is described in [SBDR08]. For other issues, refer to Section 4.7 6.2.8. Reporting the Metric Refer to Section 4.8. 6.3. Geometric Stream: Loss Episode Frequency 6.3.1. Metric Name Type-P-One-way-Bi-Packet-Loss-Geometric-Stream-Episode-Frequency 6.3.2. Metric Parameters o Src, the IP address of a source host o Dst, the IP address of a destination host o T0, the randomly selected starting time [RFC3432] for periodic launch opportunities o d, the time spacing between potential launch times, Ti and T(i+1) o n, a count of potential measurement instants o q, a launch probability o F, a selection function defining unambiguously the two packets from the stream selected for the metric o P, the specification of the packet type, over and above the source and destination address 6.3.3. Metric Units A positive number Duffield, et al. Standards Track [Page 17] RFC 6534 Loss Episode Metrics for IPPM May 2012 6.3.4. Metric Definition The result obtained by computing the Bi-Packet-Loss-Episode- Frequency-Number over a Type-P-One-way-Bi-Packet-Loss-Geometric- Stream sample with the metric parameters, then dividing the result by the launch spacing parameter d. 6.3.5. Discussion Type-P-One-way-Bi-Packet-Loss-Geometric-Stream-Episode-Frequency estimates the average frequency per unit time with which loss episodes start (or finish). The frequency relative to the count of potential probe launches is obtained by multiplying the metric value by the packet launch spacing parameter d. 6.3.6. Methodologies Refer to Section 4.6. 6.3.7. Errors and Uncertainties Because Type-P-One-way-Bi-Packet-Loss-Geometric-Stream is sampled in general (when the launch probability q <1), the metrics described in this section can be regarded as statistical estimators of the corresponding idealized version corresponding to q = 1. Estimation variance as it applies to Type-P-One-way-Bi-Packet-Loss-Geometric- Stream-Episode-Frequency is described in [SBDR08]. For other issues, refer to Section 4.7 6.3.8. Reporting the Metric Refer to Section 4.8. 7. Applicability of Loss Episode Metrics 7.1. Relation to Gilbert Model The general Gilbert-Elliot model is a discrete time Markov chain over two states, Good (g) and Bad (b), each with its own independent packet loss ratio. In the simplest case, the Good loss ratio is 0, while the Bad loss ratio is 1. Correspondingly, there are two independent parameters, the Markov transition probabilities P(g|b) = 1- P(b|b) and P(b|g) = 1- P(g|g), where P(i|j) is the probability to transition from state j and step n to state i at step n+1. With these parameters, the fraction of steps spent in the bad state is P(b|g)/(P(b|g) + P(g|b)), while the average duration of a sojourn in the bad state is 1/P(g|b) steps. Duffield, et al. Standards Track [Page 18] RFC 6534 Loss Episode Metrics for IPPM May 2012 Now identify the steps of the Markov chain with the possible sending times of packets for a Type-P-One-way-Bi-Packet-Loss-Geometric-Stream with launch spacing d. Suppose the loss episode metrics Type-P-One- way-Bi-Packet-Loss-Geometric-Stream-Ratio and Type-P-One-way-Bi- Packet-Loss-Geometric-Stream-Episode-Duration take the values r and m, respectively. Then, from the discussion in Section 6.1.5, the following can be equated: r = P(b|g)/(P(b|g) + P(g|b)) and m/d = 1/P(g|b). These relationships can be inverted in order to recover the Gilbert model parameters: P(g|b) = d/m and P(b|g)=d/m/(1/r - 1) 8. Security Considerations Conducting Internet measurements raises both security and privacy concerns. This memo does not specify an implementation of the metrics, so it does not directly affect the security of the Internet or of applications that run on the Internet. However,implementations of these metrics must be mindful of security and privacy concerns. There are two types of security concerns: potential harm caused by the measurements and potential harm to the measurements. The measurements could cause harm because they are active and inject packets into the network. The measurement parameters MUST be carefully selected so that the measurements inject trivial amounts of additional traffic into the networks they measure. If they inject "too much" traffic, they can skew the results of the measurement and, in extreme cases, cause congestion and denial of service. The measurements themselves could be harmed by routers giving measurement traffic a different priority than "normal" traffic, or by an attacker injecting artificial measurement traffic. If routers can recognize measurement traffic and treat it separately, the measurements may not reflect actual user traffic. If an attacker injects artificial traffic that is accepted as legitimate, the loss rate will be artificially lowered. Therefore, the measurement methodologies SHOULD include appropriate techniques to reduce the probability that measurement traffic can be distinguished from "normal" traffic. Authentication techniques, such as digital signatures, may be used where appropriate to guard against injected traffic attacks. The privacy concerns of network measurement are limited by the active measurements described in this memo: they involve no release of user data. Duffield, et al. Standards Track [Page 19] RFC 6534 Loss Episode Metrics for IPPM May 2012 9. References 9.1. Normative References [RFC2680] Almes, G., Kalidindi, S., and M. Zekauskas, "A One-way Packet Loss Metric for IPPM", RFC 2680, September 1999. [RFC3393] Demichelis, C. and P. Chimento, "IP Packet Delay Variation Metric for IP Performance Metrics (IPPM)", RFC 3393, November 2002. [RFC3611] Friedman, T., Caceres, R., and A. Clark, "RTP Control Protocol Extended Reports (RTCP XR)", RFC 3611, November 2003. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC3432] Raisanen, V., Grotefeld, G., and A. Morton, "Network performance measurement with periodic streams", RFC 3432, November 2002. 9.2. Informative References [RFC2330] Paxson, V., Almes, G., Mahdavi, J., and M. Mathis, "Framework for IP Performance Metrics", RFC 2330, May 1998. [RFC3357] Koodli, R. and R. Ravikanth, "One-way Loss Pattern Sample Metrics", RFC 3357, August 2002. [SBDR08] IEEE/ACM Transactions on Networking, 16(2): 307-320, "A Geometric Approach to Improving Active Packet Loss Measurement", 2008. [Gilbert] Gilbert, E.N., "Capacity of a Burst-Noise Channel. Bell System Technical Journal 39 pp 1253-1265", 1960. [Elliot] Elliott, E.O., "Estimates of Error Rates for Codes on Burst-Noise Channels. Bell System Technical Journal 42 pp 1977-1997", 1963. Duffield, et al. Standards Track [Page 20] RFC 6534 Loss Episode Metrics for IPPM May 2012 Authors' Addresses Nick Duffield AT&T Labs-Research 180 Park Avenue Florham Park, NJ 07932 USA Phone: +1 973 360 8726 Fax: +1 973 360 8871 EMail: duffield@research.att.com URI: http://www.research.att.com/people/Duffield_Nicholas_G Al Morton AT&T Labs 200 Laurel Avenue South Middletown,, NJ 07748 USA Phone: +1 732 420 1571 Fax: +1 732 368 1192 EMail: acmorton@att.com URI: http://home.comcast.net/~acmacm/ Joel Sommers Colgate University 304 McGregory Hall Hamilton, NY 13346 USA Phone: +1 315 228 7587 Fax: EMail: jsommers@colgate.edu URI: http://cs.colgate.edu/faculty/jsommers Duffield, et al. Standards Track [Page 21]