Network Working Group                                     K. Pister, Ed.
Request for Comments: 5673                                 Dust Networks
Category: Informational                                  P. Thubert, Ed.
                                                           Cisco Systems
                                                                S. Dwars
                                                                   Shell
                                                              T. Phinney
                                                              Consultant
                                                            October 2009


    Industrial Routing Requirements in Low-Power and Lossy Networks

Abstract

   The wide deployment of lower-cost wireless devices will significantly
   improve the productivity and safety of industrial plants while
   increasing the efficiency of plant workers by extending the
   information set available about the plant operations.  The aim of
   this document is to analyze the functional requirements for a routing
   protocol used in industrial Low-power and Lossy Networks (LLNs) of
   field devices.

Status of This Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (c) 2009 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the BSD License.








Pister, et al.               Informational                      [Page 1]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
     1.1.  Requirements Language  . . . . . . . . . . . . . . . . . .  3
   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  4
   3.  Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .  4
     3.1.  Applications and Traffic Patterns  . . . . . . . . . . . .  5
     3.2.  Network Topology of Industrial Applications  . . . . . . .  9
       3.2.1.  The Physical Topology  . . . . . . . . . . . . . . . . 10
       3.2.2.  Logical Topologies . . . . . . . . . . . . . . . . . . 12
   4.  Requirements Related to Traffic Characteristics  . . . . . . . 13
     4.1.  Service Requirements . . . . . . . . . . . . . . . . . . . 14
     4.2.  Configurable Application Requirement . . . . . . . . . . . 15
     4.3.  Different Routes for Different Flows . . . . . . . . . . . 15
   5.  Reliability Requirements . . . . . . . . . . . . . . . . . . . 16
   6.  Device-Aware Routing Requirements  . . . . . . . . . . . . . . 18
   7.  Broadcast/Multicast Requirements . . . . . . . . . . . . . . . 19
   8.  Protocol Performance Requirements  . . . . . . . . . . . . . . 20
   9.  Mobility Requirements  . . . . . . . . . . . . . . . . . . . . 21
   10. Manageability Requirements . . . . . . . . . . . . . . . . . . 21
   11. Antagonistic Requirements  . . . . . . . . . . . . . . . . . . 22
   12. Security Considerations  . . . . . . . . . . . . . . . . . . . 23
   13. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 25
   14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 25
     14.1. Normative References . . . . . . . . . . . . . . . . . . . 25
     14.2. Informative References . . . . . . . . . . . . . . . . . . 25

























Pister, et al.               Informational                      [Page 2]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


1.  Introduction

   Information Technology (IT) is already, and increasingly will be
   applied to industrial Control Technology (CT) in application areas
   where those IT technologies can be constrained sufficiently by
   Service Level Agreements (SLA) or other modest changes that they are
   able to meet the operational needs of industrial CT.  When that
   happens, the CT benefits from the large intellectual, experiential,
   and training investment that has already occurred in those IT
   precursors.  One can conclude that future reuse of additional IT
   protocols for industrial CT will continue to occur due to the
   significant intellectual, experiential, and training economies that
   result from that reuse.

   Following that logic, many vendors are already extending or replacing
   their local fieldbus [IEC61158] technology with Ethernet and IP-based
   solutions.  Examples of this evolution include Common Industrial
   Protocol (CIP) EtherNet/IP, Modbus/TCP, Fieldbus Foundation High
   Speed Ethernet (HSE), PROFInet, and Invensys/Foxboro FOXnet.  At the
   same time, wireless, low-power field devices are being introduced
   that facilitate a significant increase in the amount of information
   that industrial users can collect and the number of control points
   that can be remotely managed.

   IPv6 appears as a core technology at the conjunction of both trends,
   as illustrated by the current [ISA100.11a] industrial Wireless Sensor
   Networking specification, where technologies for layers 1-4 that were
   developed for purposes other than industrial CT -- [IEEE802.15.4] PHY
   and MAC, IPv6 over Low-Power Wireless Personal Area Networks
   (6LoWPANs) [RFC4919], and UDP -- are adapted to industrial CT use.
   But due to the lack of open standards for routing in Low-power and
   Lossy Networks (LLNs), even ISA100.11a leaves the routing operation
   to proprietary methods.

   The aim of this document is to analyze the requirements from the
   industrial environment for a routing protocol in Low power and Lossy
   Networks (LLNs) based on IPv6 to power the next generation of Control
   Technology.

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].







Pister, et al.               Informational                      [Page 3]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


2.  Terminology

   This document employs terminology defined in the ROLL (Routing Over
   Low-power and Lossy networks) terminology document [ROLL-TERM].  This
   document also refers to industrial standards:

   HART: Highway Addressable Remote Transducer, a group of
   specifications for industrial process and control devices
   administered by the HART Communication Foundation (see [HART]).  The
   latest version for the specifications is HART7, which includes the
   additions for WirelessHART [IEC62591].

   ISA: International Society of Automation, an ANSI-accredited
   standards-making society.  ISA100 is an ISA committee whose charter
   includes defining a family of standards for industrial automation.
   [ISA100.11a] is a working group within ISA100 that is working on a
   standard for monitoring and non-critical process control
   applications.

3.  Overview

   Wireless, low-power field devices enable industrial users to
   significantly increase the amount of information collected and the
   number of control points that can be remotely managed.  The
   deployment of these wireless devices will significantly improve the
   productivity and safety of the plants while increasing the efficiency
   of the plant workers.  IPv6 is perceived as a key technology to
   provide the scalability and interoperability that are required in
   that space, and it is more and more present in standards and products
   under development and early deployments.

   Cable is perceived as a more proven, safer technology, and existing,
   operational deployments are very stable in time.  For these reasons,
   it is not expected that wireless will replace wire in any foreseeable
   future; the consensus in the industrial space is rather that wireless
   will tremendously augment the scope and benefits of automation by
   enabling the control of devices that were not connected in the past
   for reasons of cost and/or deployment complexities.  But for LLNs to
   be adopted in the industrial environment, the wireless network needs
   to have three qualities: low power, high reliability, and easy
   installation and maintenance.  The routing protocol used for LLNs is
   important to fulfilling these goals.

   Industrial automation is segmented into two distinct application
   spaces, known as "process" or "process control" and "discrete
   manufacturing" or "factory automation".  In industrial process
   control, the product is typically a fluid (oil, gas, chemicals,
   etc.).  In factory automation or discrete manufacturing, the products



Pister, et al.               Informational                      [Page 4]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   are individual elements (screws, cars, dolls).  While there is some
   overlap of products and systems between these two segments, they are
   surprisingly separate communities.  The specifications targeting
   industrial process control tend to have more tolerance for network
   latency than what is needed for factory automation.

   Irrespective of this different 'process' and 'discrete' plant nature,
   both plant types will have similar needs for automating the
   collection of data that used to be collected manually, or was not
   collected before.  Examples are wireless sensors that report the
   state of a fuse, report the state of a luminary, HVAC status, report
   vibration levels on pumps, report man-down, and so on.

   Other novel application arenas that equally apply to both 'process'
   and 'discrete' involve mobile sensors that roam in and out of plants,
   such as active sensor tags on containers or vehicles.

   Some if not all of these applications will need to be served by the
   same low-power and lossy wireless network technology.  This may mean
   several disconnected, autonomous LLNs connecting to multiple hosts,
   but sharing the same ether.  Interconnecting such networks, if only
   to supervise channel and priority allocations, or to fully
   synchronize, or to share path capacity within a set of physical
   network components may be desired, or may not be desired for
   practical reasons, such as e.g., cyber security concerns in relation
   to plant safety and integrity.

   All application spaces desire battery-operated networks of hundreds
   of sensors and actuators communicating with LLN access points.  In an
   oil refinery, the total number of devices might exceed one million,
   but the devices will be clustered into smaller networks that in most
   cases interconnect and report to an existing plant network
   infrastructure.

   Existing wired sensor networks in this space typically use
   communication protocols with low data rates, from 1200 baud (e.g.,
   wired HART) to the 100-200 kbps range for most of the others.  The
   existing protocols are often master/slave with command/response.

3.1.  Applications and Traffic Patterns

   The industrial market classifies process applications into three
   broad categories and six classes.

   o  Safety

      *  Class 0: Emergency action - Always a critical function




Pister, et al.               Informational                      [Page 5]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   o  Control

      *  Class 1: Closed-loop regulatory control - Often a critical
         function

      *  Class 2: Closed-loop supervisory control - Usually a non-
         critical function

      *  Class 3: Open-loop control - Operator takes action and controls
         the actuator (human in the loop)

   o  Monitoring

      *  Class 4: Alerting - Short-term operational effect (for example,
         event-based maintenance)

      *  Class 5: Logging and downloading / uploading - No immediate
         operational consequence (e.g., history collection, sequence-of-
         events, preventive maintenance)

   Safety-critical functions effect the basic safety integrity of the
   plant.  These normally dormant functions kick in only when process
   control systems, or their operators, have failed.  By design and by
   regular interval inspection, they have a well-understood probability
   of failure on demand in the range of typically once per 10-1000
   years.

   In-time deliveries of messages become more relevant as the class
   number decreases.

   Note that for a control application, the jitter is just as important
   as latency and has a potential of destabilizing control algorithms.

   Industrial users are interested in deploying wireless networks for
   the monitoring classes 4 and 5, and in the non-critical portions of
   classes 2 through 3.

   Classes 4 and 5 also include asset monitoring and tracking, which
   include equipment monitoring and are essentially separate from
   process monitoring.  An example of equipment monitoring is the
   recording of motor vibrations to detect bearing wear.  However,
   similar sensors detecting excessive vibration levels could be used as
   safeguarding loops that immediately initiate a trip, and thus end up
   being class 0.

   In the near future, most LLN systems in industrial automation
   environments will be for low-frequency data collection.  Packets
   containing samples will be generated continuously, and 90% of the



Pister, et al.               Informational                      [Page 6]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   market is covered by packet rates of between 1/second and 1/hour,
   with the average under 1/minute.  In industrial process, these
   sensors include temperature, pressure, fluid flow, tank level, and
   corrosion.  Some sensors are bursty, such as vibration monitors that
   may generate and transmit tens of kilobytes (hundreds to thousands of
   packets) of time-series data at reporting rates of minutes to days.

   Almost all of these sensors will have built-in microprocessors that
   may detect alarm conditions.  Time-critical alarm packets are
   expected to be granted a lower latency than periodic sensor data
   streams.

   Some devices will transmit a log file every day, again with typically
   tens of kilobytes of data.  For these applications, there is very
   little "downstream" traffic coming from the LLN access point and
   traveling to particular sensors.  During diagnostics, however, a
   technician may be investigating a fault from a control room and
   expect to have "low" latency (human tolerable) in a command/response
   mode.

   Low-rate control, often with a "human in the loop" (also referred to
   as "open loop"), is implemented via communication to a control room
   because that's where the human in the loop will be.  The sensor data
   makes its way through the LLN access point to the centralized
   controller where it is processed, the operator sees the information
   and takes action, and the control information is then sent out to the
   actuator node in the network.

   In the future, it is envisioned that some open-loop processes will be
   automated (closed loop) and packets will flow over local loops and
   not involve the LLN access point.  These closed-loop controls for
   non-critical applications will be implemented on LLNs.  Non-critical
   closed-loop applications have a latency requirement that can be as
   low as 100 milliseconds but many control loops are tolerant of
   latencies above 1 second.

   More likely though is that loops will be closed in the field
   entirely, and in such a case, having wireless links within the
   control loop does not usually present actual value.  Most control
   loops have sensors and actuators within such proximity that a wire
   between them remains the most sensible option from an economic point
   of view.  This 'control in the field' architecture is already common
   practice with wired fieldbusses.  An 'upstream' wireless link would
   only be used to influence the in-field controller settings and to
   occasionally capture diagnostics.  Even though the link back to a
   control room might be wireless, this architecture reduces the tight
   latency and availability requirements for the wireless links.




Pister, et al.               Informational                      [Page 7]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   Closing loops in the field:

   o  does not prevent the same loop from being closed through a remote
      multivariable controller during some modes of operation, while
      being closed directly in the field during other modes of operation
      (e.g., fallback, or when timing is more critical)

   o  does not imply that the loop will be closed with a wired
      connection, or that the wired connection is more energy efficient
      even when it exists as an alternate to the wireless connection.

   A realistic future scenario is for a field device with a battery or
   ultra-capacitor power storage to have both wireless and unpowered
   wired communications capability (e.g., galvanically isolated RS-485),
   where the wireless communication is more flexible and, for local loop
   operation, more energy efficient.  The wired communication capability
   serves as a backup interconnect among the loop elements, but without
   a wired connection back to the operations center blockhouse.  In
   other words, the loop elements are interconnected through wiring to a
   nearby junction box, but the 2 km home-run link from the junction box
   to the control center does not exist.

   When wireless communication conditions are good, devices use wireless
   for loop interconnect, and either one wireless device reports alarms
   and other status to the control center for all elements of the loop,
   or each element reports independently.  When wireless communications
   are sporadic, the loop interconnect uses the self-powered
   galvanically isolated RS-485 link and one of the devices with good
   wireless communications to the control center serves as a router for
   those devices that are unable to contact the control center directly.

   The above approach is particularly attractive for large storage tanks
   in tank farms, where devices may not all have good wireless
   visibility of the control center, and where a home-run cable from the
   tank to the control center is undesirable due to the electro-
   potential differences between the tank location and the distant
   control center that arise during lightning storms.

   In fast control, tens of milliseconds of latency is typical.  In many
   of these systems, if a packet does not arrive within the specified
   interval, the system enters an emergency shutdown state, often with
   substantial financial repercussions.  For a one-second control loop
   in a system with a target of 30 years for the mean time between
   shutdowns, the latency requirement implies nine 9s of reliability
   (aka 99.9999999% reliability).  Given such exposure, given the
   intrinsic vulnerability of wireless link availability, and given the





Pister, et al.               Informational                      [Page 8]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   emergence of control in the field architectures, most users tend not
   to aim for fast closed-loop control with wireless links within that
   fast loop.

3.2.  Network Topology of Industrial Applications

   Although network topology is difficult to generalize, the majority of
   existing applications can be met by networks of 10 to 200 field
   devices and a maximum number of hops of 20.  It is assumed that the
   field devices themselves will provide routing capability for the
   network, and additional repeaters/routers will not be required in
   most cases.

   For the vast majority of industrial applications, the traffic is
   mostly composed of real-time publish/subscribe sensor data also
   referred to as buffered, from the field devices over an LLN towards
   one or more sinks.  Increasingly over time, these sinks will be a
   part of a backbone, but today they are often fragmented and isolated.

   The wireless sensor network (WSN) is an LLN of field devices for
   which two logical roles are defined, the field routers and the non-
   routing devices.  It is acceptable and even probable that the
   repartition of the roles across the field devices changes over time
   to balance the cost of the forwarding operation amongst the nodes.

   In order to scale a control network in terms of density, one possible
   architecture is to deploy a backbone as a canopy that aggregates
   multiple smaller LLNs.  The backbone is a high-speed infrastructure
   network that may interconnect multiple WSNs through backbone routers.
   Infrastructure devices can be connected to the backbone.  A gateway/
   manager that interconnects the backbone to the plant network of the
   corporate network can be viewed as collapsing the backbone and the
   infrastructure devices into a single device that operates all the
   required logical roles.  The backbone is likely to become an option
   in the industrial network.

   Typically, such backbones interconnect to the 'legacy' wired plant
   infrastructure, which is known as the plant network or Process
   Control Domain (PCD).  These plant automation networks are segregated
   domain-wise from the office network or office domain (OD), which in
   itself is typically segregated from the Internet.

   Sinks for LLN sensor data reside on the plant network (the PCD), the
   business network (the OD), and on the Internet.  Applications close
   to existing plant automation, such as wired process control and
   monitoring systems running on fieldbusses, that require high
   availability and low latencies, and that are managed by 'Control and
   Automation' departments typically reside on the PCD.  Other



Pister, et al.               Informational                      [Page 9]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   applications such as automated corrosion monitoring, cathodic
   protection voltage verification, or machine condition (vibration)
   monitoring where one sample per week is considered over-sampling,
   would more likely deliver their sensor readings in the OD.  Such
   applications are 'owned' by, e.g., maintenance departments.

   Yet other applications like third-party-maintained luminaries, or
   vendor-managed inventory systems, where a supplier of chemicals needs
   access to tank level readings at his customer's site, will be best
   served with direct Internet connectivity all the way to its sensor at
   his customer's site.  Temporary 'babysitting sensors' deployed for
   just a few days, say during startup or troubleshooting or for ad hoc
   measurement campaigns for research and development purposes, are
   other examples where Internet would be the domain where wireless
   sensor data would land, and other domains such as the OD and PCD
   should preferably be circumvented if quick deployment without
   potentially impacting plant safety integrity is required.

   This multiple-domain multiple-application connectivity creates a
   significant challenge.  Many different applications will all share
   the same medium, the ether, within the fence, preferably sharing the
   same frequency bands, and preferably sharing the same protocols,
   preferably synchronized to optimize coexistence challenges, yet
   logically segregated to avoid creation of intolerable shortcuts
   between existing wired domains.

   Given this challenge, LLNs are best to be treated as all sitting on
   yet another segregated domain, segregated from all other wired
   domains where conventional security is organized by perimeter.
   Moving away from the traditional perimeter-security mindset means
   moving towards stronger end-device identity authentication, so that
   LLN access points can split the various wireless data streams and
   interconnect back to the appropriate domain (pending the gateways'
   establishment of the message originators' identity and trust).

   Similar considerations are to be given to how multiple applications
   may or may not be allowed to share routing devices and their
   potentially redundant bandwidth within the network.  Challenges here
   are to balance available capacity, required latencies, expected
   priorities, and (last but not least) available (battery) energy
   within the routing devices.

3.2.1.  The Physical Topology

   There is no specific physical topology for an industrial process
   control network.





Pister, et al.               Informational                     [Page 10]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   One extreme example is a multi-square-kilometer refinery where
   isolated tanks, some of them with power but most with no backbone
   connectivity, compose a farm that spans over of the surface of the
   plant.  A few hundred field devices are deployed to ensure the global
   coverage using a wireless self-forming self-healing mesh network that
   might be 5 to 10 hops across.  Local feedback loops and mobile
   workers tend to be only 1 or 2 hops.  The backbone is in the refinery
   proper, many hops away.  Even there, powered infrastructure is also
   typically several hops away.  In that case, hopping to/from the
   powered infrastructure may often be more costly than the direct
   route.

   In the opposite extreme case, the backbone network spans all the
   nodes and most nodes are in direct sight of one or more backbone
   routers.  Most communication between field devices and infrastructure
   devices, as well as field device to field device, occurs across the
   backbone.  From afar, this model resembles the WiFi ESS (Extended
   Service Set).  But from a layer-3 (L3) perspective, the issues are
   the default (backbone) router selection and the routing inside the
   backbone, whereas the radio hop towards the field device is in fact a
   simple local delivery.

            ---------+----------------------------
                     |          Plant Network
                     |
                  +-----+
                  |     | Gateway             M : Mobile device
                  |     |                     o : Field device
                  +-----+
                     |
                     |      Backbone
               +--------------------+------------------+
               |                    |                  |
            +-----+             +-----+             +-----+
            |     | Backbone    |     | Backbone    |     | Backbone
            |     | router      |     | router      |     | router
            +-----+             +-----+             +-----+
               o    o   o    o     o   o  o   o   o   o  o   o o
           o o   o  o   o  o  o o   o  o  o   o   o   o  o  o  o o
          o  o o  o o    o   o   o  o  o  o    M    o  o  o o o
          o   o  M o  o  o     o  o    o  o  o    o  o   o  o   o
            o   o o       o        o  o         o        o o
                    o           o          o             o     o
                           LLN

                Figure 1: Backbone-Based Physical Topology





Pister, et al.               Informational                     [Page 11]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   An intermediate case is illustrated in Figure 1 with a backbone that
   spans the Wireless Sensor Network in such a fashion that any WSN node
   is only a few wireless hops away from the nearest backbone router.
   WSN nodes are expected to organize into self-forming, self-healing,
   self-optimizing logical topologies that enable leveraging the
   backbone when it is most efficient to do so.

   It must be noted that the routing function is expected to be so
   simple that any field device could assume the role of a router,
   depending on the self-discovery of the topology and the power status
   of the neighbors.  On the other hand, only devices equipped with the
   appropriate hardware and software combination could assume the role
   of an endpoint for a given purpose, such as sensor or actuator.

3.2.2.  Logical Topologies

   Most of the traffic over the LLN is publish/subscribe of sensor data
   from the field device towards a sink that can be a backbone router, a
   gateway, or a controller/manager.  The destination of the sensor data
   is an infrastructure device that sits on the backbone and is
   reachable via one or more backbone routers.

   For security, reliability, availability, or serviceability reasons,
   it is often required that the logical topologies are not physically
   congruent over the radio network; that is, they form logical
   partitions of the LLN.  For instance, a routing topology that is set
   up for control should be isolated from a topology that reports the
   temperature and the status of the vents, if that second topology has
   lesser constraints for the security policy.  This isolation might be
   implemented as Virtual LANs and Virtual Routing Tables in shared
   nodes in the backbone, but correspond effectively to physical nodes
   in the wireless network.

   Since publishing the data is the raison d'etre for most of the
   sensors, in some cases it makes sense to build proactively a set of
   routes between the sensors and one or more backbone routers and
   maintain those routes at all time.  Also, because of the lossy nature
   of the network, the routing in place should attempt to propose
   multiple paths in the form of Directed Acyclic Graphs oriented
   towards the destination.

   In contrast with the general requirement of maintaining default
   routes towards the sinks, the need for field device to field device
   (FD-to-FD) connectivity is very specific and rare, though the traffic
   associated might be of foremost importance.  FD-to-FD routes are
   often the most critical, optimized, and well-maintained routes.  A
   class 0 safeguarding loop requires guaranteed delivery and extremely
   tight response times.  Both the respect of criteria in the route



Pister, et al.               Informational                     [Page 12]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   computation and the quality of the maintenance of the route are
   critical for the field devices' operation.  Typically, a control loop
   will be using a dedicated direct wire that has very different
   capabilities, cost, and constraints than the wireless medium, with
   the need to use a wireless path as a backup route only in case of
   loss of the wired path.

   Considering that each FD-to-FD route computation has specific
   constraints in terms of latency and availability, it can be expected
   that the shortest path possible will often be selected and that this
   path will be routed inside the LLN as opposed to via the backbone.
   It can also be noted that the lifetimes of the routes might range
   from minutes for a mobile worker to tens of years for a command and
   control closed loop.  Finally, time-varying user requirements for
   latency and bandwidth will change the constraints on the routes,
   which might either trigger a constrained route recomputation, a
   reprovisioning of the underlying L2 protocols, or both in that order.
   For instance, a wireless worker may initiate a bulk transfer to
   configure or diagnose a field device.  A level sensor device may need
   to perform a calibration and send a bulk file to a plant.

4.  Requirements Related to Traffic Characteristics

   [ISA100.11a] selected IPv6 as its network layer for a number of
   reasons, including the huge address space and the large potential
   size of a subnet, which can range up to 10K nodes in a plant
   deployment.  In the ISA100 model, industrial applications fall into
   four large service categories:

   1.  Periodic data (aka buffered).  Data that is generated
       periodically and has a well understood data bandwidth
       requirement, both deterministic and predictable.  Timely delivery
       of such data is often the core function of a wireless sensor
       network and permanent resources are assigned to ensure that the
       required bandwidth stays available.  Buffered data usually
       exhibits a short time to live, and the newer reading obsoletes
       the previous.  In some cases, alarms are low-priority information
       that gets repeated over and over.  The end-to-end latency of this
       data is not as important as the regularity with which the data is
       presented to the plant application.

   2.  Event data.  This category includes alarms and aperiodic data
       reports with bursty data bandwidth requirements.  In certain
       cases, alarms are critical and require a priority service from
       the network.






Pister, et al.               Informational                     [Page 13]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   3.  Client/Server.  Many industrial applications are based on a
       client/server model and implement a command response protocol.
       The data bandwidth required is often bursty.  The acceptable
       round-trip latency for some legacy systems was based on the time
       to send tens of bytes over a 1200 baud link.  Hundreds of
       milliseconds is typical.  This type of request is statistically
       multiplexed over the LLN and cost-based, fair-share, best-effort
       service is usually expected.

   4.  Bulk transfer.  Bulk transfers involve the transmission of blocks
       of data in multiple packets where temporary resources are
       assigned to meet a transaction time constraint.  Transient
       resources are assigned for a limited time (related to file size
       and data rate) to meet the bulk transfers service requirements.

4.1.  Service Requirements

   The following service parameters can affect routing decisions in a
   resource-constrained network:

   o  Data bandwidth - the bandwidth might be allocated permanently or
      for a period of time to a specific flow that usually exhibits
      well-defined properties of burstiness and throughput.  Some
      bandwidth will also be statistically shared between flows in a
      best-effort fashion.

   o  Latency - the time taken for the data to transit the network from
      the source to the destination.  This may be expressed in terms of
      a deadline for delivery.  Most monitoring latencies will be in
      seconds to minutes.

   o  Transmission phase - process applications can be synchronized to
      wall clock time and require coordinated transmissions.  A common
      coordination frequency is 4 Hz (250 ms).

   o  Service contract type - revocation priority.  LLNs have limited
      network resources that can vary with time.  This means the system
      can become fully subscribed or even over-subscribed.  System
      policies determine how resources are allocated when resources are
      over-subscribed.  The choices are blocking and graceful
      degradation.

   o  Transmission priority - the means by which limited resources
      within field devices are allocated across multiple services.  For
      transmissions, a device has to select which packet in its queue
      will be sent at the next transmission opportunity.  Packet
      priority is used as one criterion for selecting the next packet.
      For reception, a device has to decide how to store a received



Pister, et al.               Informational                     [Page 14]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


      packet.  The field devices are memory-constrained and receive
      buffers may become full.  Packet priority is used to select which
      packets are stored or discarded.

   The routing protocol MUST also support different metric types for
   each link used to compute the path according to some objective
   function (e.g., minimize latency) depending on the nature of the
   traffic.

   For these reasons, the ROLL routing infrastructure is REQUIRED to
   compute and update constrained routes on demand, and it can be
   expected that this model will become more prevalent for FD-to-FD
   connectivity as well as for some FD-to-infrastructure-device
   connectivity over time.

   Industrial application data flows between field devices are not
   necessarily symmetric.  In particular, asymmetrical cost and
   unidirectional routes are common for published data and alerts, which
   represent the most part of the sensor traffic.  The routing protocol
   MUST be able to compute a set of unidirectional routes with
   potentially different costs that are composed of one or more non-
   congruent paths.

   As multiple paths are set up and a variety of flows traverse the
   network towards a same destination (for instance, a node acting as a
   sink for the LLN), the use of an additional marking/tagging mechanism
   based on upper-layer information will be REQUIRED for intermediate
   routers to discriminate the flows and perform the appropriate routing
   decision using only the content of the IPv6 packet (e.g., use of
   DSCP, Flow Label).

4.2.  Configurable Application Requirement

   Time-varying user requirements for latency and bandwidth may require
   changes in the provisioning of the underlying L2 protocols.  A
   technician may initiate a query/response session or bulk transfer to
   diagnose or configure a field device.  A level sensor device may need
   to perform a calibration and send a bulk file to a plant.  The
   routing protocol MUST support the ability to recompute paths based on
   network-layer abstractions of the underlying link attributes/metrics
   that may change dynamically.

4.3.  Different Routes for Different Flows

   Because different services categories have different service
   requirements, it is often desirable to have different routes for
   different data flows between the same two endpoints.  For example,
   alarm or periodic data from A to Z may require path diversity with



Pister, et al.               Informational                     [Page 15]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   specific latency and reliability.  A file transfer between A and Z
   may not need path diversity.  The routing algorithm MUST be able to
   generate different routes with different characteristics (e.g.,
   optimized according to different costs, etc.).

   Dynamic or configured states of links and nodes influence the
   capability of a given path to fulfill operational requirements such
   as stability, battery cost, or latency.  Constraints such as battery
   lifetime derive from the application itself, and because industrial
   applications data flows are typically well-defined and well-
   controlled, it is usually possible to estimate the battery
   consumption of a router for a given topology.

   The routing protocol MUST support the ability to (re)compute paths
   based on network-layer abstractions of upper-layer constraints to
   maintain the level of operation within required parameters.  Such
   information MAY be advertised by the routing protocol as metrics that
   enable routing algorithms to establish appropriate paths that fit the
   upper-layer constraints.

   The handling of an IPv6 packet by the network layer operates on the
   standard properties and the settings of the IPv6 packet header
   fields.  These fields include the 3-tuple of the Flow Label and the
   Source and Destination Address that can be used to identify a flow
   and the Traffic Class octet that can be used to influence the Per Hop
   Behavior in intermediate routers.

   An application MAY choose how to set those fields for each packet or
   for streams of packets, and the routing protocol specification SHOULD
   state how different field settings will be handled to perform
   different routing decisions.

5.  Reliability Requirements

   LLN reliability constitutes several unrelated aspects:

   1)  Availability of source-to-destination connectivity when the
       application needs it, expressed in number of successes divided by
       number of attempts.

   2)  Availability of source-to-destination connectivity when the
       application might need it, expressed in number of potential
       failures / available bandwidth,

   3)  Ability, expressed in number of successes divided by number of
       attempts to get data delivered from source to destination within
       a capped time,




Pister, et al.               Informational                     [Page 16]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   4)  How well a network (serving many applications) achieves end-to-
       end delivery of packets within a bounded latency,

   5)  Trustworthiness of data that is delivered to the sinks,

   6)  and others depending on the specific case.

   This makes quantifying reliability the equivalent of plotting it on a
   three (or more) dimensional graph.  Different applications have
   different requirements, and expressing reliability as a one
   dimensional parameter, like 'reliability on my wireless network is
   99.9%' often creates more confusion than clarity.

   The impact of not receiving sensor data due to sporadic network
   outages can be devastating if this happens unnoticed.  However, if
   destinations that expect periodic sensor data or alarm status updates
   fail to get them, then automatically these systems can take
   appropriate actions that prevent dangerous situations.  Pending the
   wireless application, appropriate action ranges from initiating a
   shutdown within 100 ms, to using a last known good value for as much
   as N successive samples, to sending out an operator into the plant to
   collect monthly data in the conventional way, i.e., some portable
   sensor, or paper and a clipboard.

   The impact of receiving corrupted data, and not being able to detect
   that received data is corrupt, is often more dangerous.  Data
   corruption can either come from random bit errors due to white noise,
   or from occasional bursty interference sources like thunderstorms or
   leaky microwave ovens, but also from conscious attacks by
   adversaries.

   Another critical aspect for the routing is the capability to ensure
   maximum disruption time and route maintenance.  The maximum
   disruption time is the time it takes at most for a specific path to
   be restored when broken.  Route maintenance ensures that a path is
   monitored cannot stay disrupted for more than the maximum disruption
   time.  Maintenance should also ensure that a path continues to
   provide the service for which it was established, for instance, in
   terms of bandwidth, jitter, and latency.

   In industrial applications, availability is usually defined with
   respect to end-to-end delivery of packets within a bounded latency.
   Availability requirements vary over many orders of magnitude.  Some
   non-critical monitoring applications may tolerate an availability of
   less than 90% with hours of latency.  Most industrial standards, such
   as HART7 [IEC62591], have set user availability expectations at
   99.9%.  Regulatory requirements are a driver for some industrial
   applications.  Regulatory monitoring requires high data integrity



Pister, et al.               Informational                     [Page 17]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   because lost data is assumed to be out of compliance and subject to
   fines.  This can drive up either availability or trustworthiness
   requirements.

   Because LLN link stability is often low, path diversity is critical.
   Hop-by-hop link diversity is used to improve latency-bounded
   reliability by sending data over diverse paths.

   Because data from field devices are aggregated and funneled at the
   LLN access point before they are routed to plant applications, LLN
   access point redundancy is an important factor in overall
   availability.  A route that connects a field device to a plant
   application may have multiple paths that go through more than one LLN
   access point.  The routing protocol MUST be able to compute paths of
   not-necessarily-equal cost toward a given destination so as to enable
   load-balancing across a variety of paths.  The availability of each
   path in a multipath route can change over time.  Hence, it is
   important to measure the availability on a per-path basis and select
   a path (or paths) according to the availability requirements.

6.  Device-Aware Routing Requirements

   Wireless LLN nodes in industrial environments are powered by a
   variety of sources.  Battery-operated devices with lifetime
   requirements of at least five years are the most common.  Battery
   operated devices have a cap on their total energy, and typically can
   report an estimate of remaining energy, and typically do not have
   constraints on the short-term average power consumption.  Energy-
   scavenging devices are more complex.  These systems contain both a
   power-scavenging device (such as solar, vibration, or temperature
   difference) and an energy storage device, such as a rechargeable
   battery or a capacitor.  These systems, therefore, have limits on
   both long-term average power consumption (which cannot exceed the
   average scavenged power over the same interval) as well as the short-
   term limits imposed by the energy storage requirements.  For solar-
   powered systems, the energy storage system is generally designed to
   provide days of power in the absence of sunlight.  Many industrial
   sensors run off of a 4-20 mA current loop, and can scavenge on the
   order of milliwatts from that source.  Vibration monitoring systems
   are a natural choice for vibration scavenging, which typically only
   provides tens or hundreds of microwatts.  Due to industrial
   temperature ranges and desired lifetimes, the choices of energy
   storage devices can be limited, and the resulting stored energy is
   often comparable to the energy cost of sending or receiving a packet
   rather than the energy of operating the node for several days.  And
   of course, some nodes will be line-powered.





Pister, et al.               Informational                     [Page 18]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   Example 1: solar panel, lead-acid battery sized for two weeks of
   rain.

   Example 2: vibration scavenger, 1 mF tantalum capacitor.

   Field devices have limited resources.  Low-power, low-cost devices
   have limited memory for storing route information.  Typical field
   devices will have a finite number of routes they can support for
   their embedded sensor/actuator application and for forwarding other
   devices packets in a mesh network slotted-link.

   Users may strongly prefer that the same device have different
   lifetime requirements in different locations.  A sensor monitoring a
   non-critical parameter in an easily accessed location may have a
   lifetime requirement that is shorter and may tolerate more
   statistical variation than a mission-critical sensor in a hard-to-
   reach place that requires a plant shutdown in order to replace.

   The routing algorithm MUST support node-constrained routing (e.g.,
   taking into account the existing energy state as a node constraint).
   Node constraints include power and memory, as well as constraints
   placed on the device by the user, such as battery life.

7.  Broadcast/Multicast Requirements

   Some existing industrial plant applications do not use broadcast or
   multicast addressing to communicate to field devices.  Unicast
   address support is sufficient for them.

   In some other industrial process automation environments, multicast
   over IP is used to deliver to multiple nodes that may be functionally
   similar or not.  Example usages are:

   1)  Delivery of alerts to multiple similar servers in an automation
       control room.  Alerts are multicast to a group address based on
       the part of the automation process where the alerts arose (e.g.,
       the multicast address "all-nodes-interested-in-alerts-for-
       process-unit-X").  This is always a restricted-scope multicast,
       not a broadcast.

   2)  Delivery of common packets to multiple routers over a backbone,
       where the packets result in each receiving router initiating
       multicast (sometimes as a full broadcast) within the LLN.  For
       instance, this can be a byproduct of having potentially
       physically separated backbone routers that can inject messages
       into different portions of the same larger LLN.





Pister, et al.               Informational                     [Page 19]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   3)  Publication of measurement data to more than one subscriber.
       This feature is useful in some peer-to-peer control applications.
       For example, level position may be useful to a controller that
       operates the flow valve and also to the overfill alarm indicator.
       Both controller and alarm indicator would receive the same
       publication sent as a multicast by the level gauge.

   All of these uses require an 1:N security mechanism as well; they
   aren't of any use if the end-to-end security is only point-to-point.

   It is quite possible that first-generation wireless automation field
   networks can be adequately useful without either of these
   capabilities, but in the near future, wireless field devices with
   communication controllers and protocol stacks will require control
   and configuration, such as firmware downloading, that may benefit
   from broadcast or multicast addressing.

   The routing protocol SHOULD support multicast addressing.

8.  Protocol Performance Requirements

   The routing protocol MUST converge after the addition of a new device
   within several minutes, and SHOULD converge within tens of seconds
   such that a device is able to establish connectivity to any other
   point in the network or determine that there is a connectivity issue.
   Any routing algorithm used to determine how to route packets in the
   network, MUST be capable of routing packets to and from a newly added
   device within several minutes of its addition, and SHOULD be able to
   perform this function within tens of seconds.

   The routing protocol MUST distribute sufficient information about
   link failures to enable traffic to be routed such that all service
   requirements (especially latency) continue to be met.  This places a
   requirement on the speed of distribution and convergence of this
   information as well as the responsiveness of any routing algorithms
   used to determine how to route packets.  This requirement only
   applies at normal link failure rates (see Section 5) and MAY degrade
   during failure storms.

   Any algorithm that computes routes for packets in the network MUST be
   able to perform route computations in advance of needing to use the
   route.  Since such algorithms are required to react to link failures,
   link usage information, and other dynamic link properties as the
   information is distributed by the routing protocol, the algorithms
   SHOULD recompute route based on the receipt of new information.






Pister, et al.               Informational                     [Page 20]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


9.  Mobility Requirements

   Various economic factors have contributed to a reduction of trained
   workers in the industrial plant.  A very common problem is that of
   the "wireless worker".  Carrying a PDA or something similar, this
   worker will be able to accomplish more work in less time than the
   older, better-trained workers that he or she replaces.  Whether the
   premise is valid, the use case is commonly presented: the worker will
   be wirelessly connected to the plant IT system to download
   documentation, instructions, etc., and will need to be able to
   connect "directly" to the sensors and control points in or near the
   equipment on which he or she is working.  It is possible that this
   "direct" connection could come via the normal LLNs data collection
   network.  This connection is likely to require higher bandwidth and
   lower latency than the normal data collection operation.

   PDAs are typically used as the user interfaces for plant historians,
   asset management systems, and the like.  It is undecided if these
   PDAs will use the LLN directly to talk to field sensors, or if they
   will rather use other wireless connectivity that proxies back into
   the field or to anywhere else.

   The routing protocol SHOULD support the wireless worker with fast
   network connection times of a few of seconds, and low command and
   response latencies to the plant behind the LLN access points, to
   applications, and to field devices.  The routing protocol SHOULD also
   support the bandwidth allocation for bulk transfers between the field
   device and the handheld device of the wireless worker.  The routing
   protocol SHOULD support walking speeds for maintaining network
   connectivity as the handheld device changes position in the wireless
   network.

   Some field devices will be mobile.  These devices may be located on
   moving parts such as rotating components, or they may be located on
   vehicles such as cranes or fork lifts.  The routing protocol SHOULD
   support vehicular speeds of up to 35 kmph.

10.  Manageability Requirements

   The process and control industry is manpower constrained.  The aging
   demographics of plant personnel are causing a looming manpower
   problem for industry across many markets.  The goal for the
   industrial networks is to have the installation process not require
   any new skills for the plant personnel.  The person would install the
   wireless sensor or wireless actuator the same way the wired sensor or
   wired actuator is installed, except the step to connect wire is
   eliminated.




Pister, et al.               Informational                     [Page 21]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   Most users in fact demand even much further simplified provisioning
   methods, a plug and play operation that would be fully transparent to
   the user.  This requires availability of open and untrusted side
   channels for new joiners, and it requires strong and automated
   authentication so that networks can automatically accept or reject
   new joiners.  Ideally, for a user, adding new routing devices should
   be as easy as dragging and dropping an icon from a pool of
   authenticated new joiners into a pool for the wired domain that this
   new sensor should connect to.  Under the hood, invisible to the user,
   auditable security mechanisms should take care of new device
   authentication, and secret join key distribution.  These more
   sophisticated 'over the air' secure provisioning methods should
   eliminate the use of traditional configuration tools for setting up
   devices prior to being ready to securely join an LLN access point.

   The routing protocol SHOULD be fully configurable over the air as
   part of the joining process of a new routing device.

   There will be many new applications where even without any human
   intervention at the plant, devices that have never been on site
   before, should be allowed, based on their credentials and
   cryptographic capabilities, to connect anyway.  Examples are third-
   party road tankers, rail cargo containers with overfill protection
   sensors, or consumer cars that need to be refueled with hydrogen by
   robots at future fueling stations.

   The routing protocol for LLNs is expected to be easy to deploy and
   manage.  Because the number of field devices in a network is large,
   provisioning the devices manually may not make sense.  The proper
   operation of the routing protocol MAY require that the node be
   commissioned with information about itself, like identity, security
   tokens, radio standards and frequencies, etc.

   The routing protocol SHOULD NOT require to preprovision information
   about the environment where the node will be deployed.  The routing
   protocol MUST enable the full discovery and setup of the environment
   (available links, selected peers, reachable network).  The protocol
   MUST enable the distribution of its own configuration to be performed
   by some external mechanism from a centralized management controller.

11.  Antagonistic Requirements

   This document contains a number of strongly required constraints on
   the ROLL routing protocol.  Some of those strong requirements might
   appear antagonistic and, as such, impossible to fulfill at the same
   time.





Pister, et al.               Informational                     [Page 22]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   For instance, the strong requirement of power economy applies on
   general routing but is variant since it is reasonable to spend more
   energy on ensuring the availability of a short emergency closed-loop
   path than it is to maintain an alert path that is used for regular
   updates on the operating status of the device.  In the same fashion,
   the strong requirement on easy provisioning does not match easily the
   strong security requirements that can be needed to implement a
   factory policy.  Then again, a non-default non-trivial setup can be
   acceptable as long as the default configuration enables a device to
   join with some degree of security.

   Convergence time and network size are also antagonistic.  The values
   expressed in Section 8 ("Protocol Performance Requirements") apply to
   an average network with tens of devices.  The use of a backbone can
   maintain that level of performance and still enable to grow the
   network to thousands of node.  In any case, it is acceptable to grow
   reasonably the convergence time with the network size.

12.  Security Considerations

   Given that wireless sensor networks in industrial automation operate
   in systems that have substantial financial and human safety
   implications, security is of considerable concern.  Levels of
   security violation that are tolerated as a "cost of doing business"
   in the banking industry are not acceptable when in some cases
   literally thousands of lives may be at risk.

   Security is easily confused with guarantee for availability.  When
   discussing wireless security, it's important to distinguish clearly
   between the risks of temporarily losing connectivity, say due to a
   thunderstorm, and the risks associated with knowledgeable adversaries
   attacking a wireless system.  The conscious attacks need to be split
   between 1) attacks on the actual application served by the wireless
   devices and 2) attacks that exploit the presence of a wireless access
   point that may provide connectivity onto legacy wired plant networks,
   so these are attacks that have little to do with the wireless devices
   in the LLNs.  In the second type of attack, access points that might
   be wireless backdoors that allow an attacker outside the fence to
   access typically non-secured process control and/or office networks
   are typically the ones that do create exposures where lives are at
   risk.  This implies that the LLN access point on its own must possess
   functionality that guarantees domain segregation, and thus prohibits
   many types of traffic further upstream.

   The current generation of industrial wireless device manufacturers is
   specifying security at the MAC (Media Access Control) layer and the
   transport layer.  A shared key is used to authenticate messages at
   the MAC layer.  At the transport layer, commands are encrypted with



Pister, et al.               Informational                     [Page 23]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   statistically unique randomly generated end-to-end session keys.
   HART7 [IEC62591] and ISA100.11a are examples of security systems for
   industrial wireless networks.

   Although such symmetric key encryption and authentication mechanisms
   at MAC and transport layers may protect reasonably well during the
   lifecycle, the initial network boot (provisioning) step in many cases
   requires more sophisticated steps to securely land the initial secret
   keys in field devices.  Also, it is vital that during these steps,
   the ease of deployment and the freedom of mixing and matching
   products from different suppliers does not complicate life for those
   that deploy and commission.  Given the average skill levels in the
   field and the serious resource constraints in the market, investing a
   little bit more in sensor-node hardware and software so that new
   devices automatically can be deemed trustworthy, and thus
   automatically join the domains that they should join, with just one
   drag-and-drop action for those in charge of deploying, will yield
   faster adoption and proliferation of the LLN technology.

   Industrial plants may not maintain the same level of physical
   security for field devices that is associated with traditional
   network sites such as locked IT centers.  In industrial plants, it
   must be assumed that the field devices have marginal physical
   security and might be compromised.  The routing protocol SHOULD limit
   the risk incurred by one node being compromised, for instance by
   proposing a non-congruent path for a given route and balancing the
   traffic across the network.

   The routing protocol SHOULD compartmentalize the trust placed in
   field devices so that a compromised field device does not destroy the
   security of the whole network.  The routing MUST be configured and
   managed using secure messages and protocols that prevent outsider
   attacks and limit insider attacks from field devices installed in
   insecure locations in the plant.

   The wireless environment typically forces the abandonment of
   classical 'by perimeter' thinking when trying to secure network
   domains.  Wireless nodes in LLN networks should thus be regarded as
   little islands with trusted kernels, situated in an ocean of
   untrusted connectivity, an ocean that might be full of pirate ships.
   Consequently, confidence in node identity and ability to challenge
   authenticity of source node credentials gets more relevant.
   Cryptographic boundaries inside devices that clearly demark the
   border between trusted and untrusted areas need to be drawn.
   Protection against compromise of the cryptographic boundaries inside
   the hardware of devices is outside of the scope of this document.





Pister, et al.               Informational                     [Page 24]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   Note that because nodes are usually expected to be capable of
   routing, the end-node security requirements are usually a superset of
   the router requirements, in order to prevent a end node from being
   used to inject forged information into the network that could alter
   the plant operations.

   Additional details of security across all application scenarios are
   provided in the ROLL security framework [ROLL-SEC-FMWK].
   Implications of these security requirements for the routing protocol
   itself are a topic for future work.

13.  Acknowledgements

   Many thanks to Rick Enns, Alexander Chernoguzov, and Chol Su Kang for
   their contributions.

14.  References

14.1.  Normative References

   [RFC2119]        Bradner, S., "Key words for use in RFCs to Indicate
                    Requirement Levels", BCP 14, RFC 2119, March 1997.

14.2.  Informative References

   [HART]           HART (Highway Addressable Remote Transducer)
                    Communication Foundation, "HART Communication
                    Protocol and Foundation - Home Page",
                    <http://www.hartcomm.org>.

   [IEC61158]       IEC, "Industrial communication networks - Fieldbus
                    specifications", IEC 61158 series.

   [IEC62591]       IEC, "Industrial communication networks - Wireless
                    communication network and communication profiles -
                    WirelessHART", IEC 62591.

   [IEEE802.15.4]   IEEE, "Telecommunications and information exchange
                    between systems -- Local and metropolitan area
                    networks -- Specific requirements Part 15.4:
                    Wireless Medium Access Control (MAC) and Physical
                    Layer (PHY) Specifications for Low-Rate Wireless
                    Personal Area Networks (WPANs)", IEEE 802.15.4,
                    2006.







Pister, et al.               Informational                     [Page 25]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


   [ISA100.11a]     ISA, "Wireless systems for industrial automation:
                    Process control and related applications",
                    ISA 100.11a, May 2008, <http://www.isa.org/
                    Community/SP100WirelessSystemsforAutomation>.

   [RFC4919]        Kushalnagar, N., Montenegro, G., and C. Schumacher,
                    "IPv6 over Low-Power Wireless Personal Area Networks
                    (6LoWPANs): Overview, Assumptions, Problem
                    Statement, and Goals", RFC 4919, August 2007.

   [ROLL-SEC-FMWK]  Tsao, T., Alexander, R., Dohler, M., Daza, V., and
                    A. Lozano, "A Security Framework for Routing over
                    Low Power and Lossy Networks", Work in Progress,
                    September 2009.

   [ROLL-TERM]      Vasseur, JP., "Terminology in Low power And Lossy
                    Networks", Work in Progress, October 2009.


































Pister, et al.               Informational                     [Page 26]


RFC 5673            Industrial Routing Reqs in LLNs         October 2009


Authors' Addresses

   Kris Pister (editor)
   Dust Networks
   30695 Huntwood Ave.
   Hayward, CA  94544
   USA

   EMail: kpister@dustnetworks.com


   Pascal Thubert (editor)
   Cisco Systems
   Village d'Entreprises Green Side
   400, Avenue de Roumanille
   Batiment T3
   Biot - Sophia Antipolis  06410
   FRANCE

   Phone: +33 497 23 26 34
   EMail: pthubert@cisco.com


   Sicco Dwars
   Shell Global Solutions International B.V.
   Sir Winston Churchilllaan 299
   Rijswijk  2288 DC
   Netherlands

   Phone: +31 70 447 2660
   EMail: sicco.dwars@shell.com


   Tom Phinney
   Consultant
   5012 W. Torrey Pines Circle
   Glendale, AZ  85308-3221
   USA

   Phone: +1 602 938 3163
   EMail: tom.phinney@cox.net










Pister, et al.               Informational                     [Page 27]