Network Working Group D. Zelig, Ed. Request for Comments: 5602 Oversi Category: Standards Track T. Nadeau, Ed. BT July 2009 Pseudowire (PW) over MPLS PSN Management Information Base (MIB) Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes a MIB module for PW operation over Multiprotocol Label Switching (MPLS) Label Switching Routers (LSRs). Status of This Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Copyright Notice Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents in effect on the date of publication of this document (http://trustee.ietf.org/license-info). Please review these documents carefully, as they describe your rights and restrictions with respect to this document. This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English. Zelig & Nadeau Standards Track [Page 1] RFC 5602 PW MPLS MIB July 2009 Table of Contents 1. Introduction ....................................................2 2. The Internet-Standard Management Framework ......................2 3. Terminology .....................................................3 4. Overview ........................................................3 5. Features Checklist ..............................................4 6. MIB Module Usage ................................................5 7. PW-MPLS-STD-MIB Example .........................................7 8. Object Definitions ..............................................8 9. Security Considerations ........................................28 10. IANA Considerations ...........................................29 11. References ....................................................29 11.1. Normative References .....................................29 11.2. Informative References ...................................30 1. Introduction This document describes a model for managing pseudowire services for transmission over different flavors of MPLS tunnels. The general PW MIB module [RFC5601] defines the parameters global to the PW regardless of the underlying Packet Switched Network (PSN) and emulated service. This document is applicable for PWs that use MPLS PSN type in the PW-STD-MIB. This document describes the MIB objects that define pseudowire association to the MPLS PSN, in a way that is not specific to the carried service. Together, [RFC3811] and [RFC3812] describe the modeling of an MPLS tunnel, and a tunnel's underlying cross-connects. This MIB module supports MPLS-TE PSN, non-TE MPLS PSN (an outer tunnel created by the Label Distribution Protocol (LDP) or manually), and MPLS PW label only (no outer tunnel). 2. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB Zelig & Nadeau Standards Track [Page 2] RFC 5602 PW MPLS MIB July 2009 module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 3. Terminology This document uses terminology from the document describing the PW architecture [RFC3985], [RFC3916], and [RFC4447]. The terms "outbound" and "inbound" in this MIB module are based on the common practice in the MPLS standards; i.e. "outbound" is toward the PSN. However, where these terms are used in an object name, the object description clarifies the exact packet direction to prevent confusion with these terms in other documents. "PSN tunnel" is a general term indicating a virtual connection between the two Pseudowire Emulation Edge-to-Edge (PWE3) edge devices. Each tunnel may potentially carry multiple PWs inside. An MPLS tunnel is within the scope of this document. This document uses terminology from the document describing the MPLS architecture [RFC3031] for MPLS PSN. A Label Switched Path (LSP) is modeled as described in [RFC3811] and [RFC3812] via a series of cross-connects through one or more Label Switching Routers (LSRs). In MPLS PSN, a PW connection typically uses a PW label within a tunnel label [RFC4447]. Multiple pseudowires each with a unique PW label can share the same tunnel. For PW transport over MPLS, the tunnel label is known as the "outer" label, while the PW label is known as the "inner" label. An exception to this is with adjacent LSRs or the use of a Penultimate Hop Popping (PHP). In this case, there is an option for PWs to connect directly without an outer label. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [BCP14]. 4. Overview The MIB module structure for defining a PW service consists of three layers of MIB modules functioning together. This general model is defined in the PWE3 architecture [RFC3985]. The layering model is intended to sufficiently isolate PW services from the underlying PSN layer that carries the emulated service. This is done at the same time as providing a standard means for connecting any supported services to any supported PSNs. Zelig & Nadeau Standards Track [Page 3] RFC 5602 PW MPLS MIB July 2009 The first layer, known as the service layer, contains service- specific modules. These modules define service-specific management objects that interface or collaborate with existing MIB modules for the native version of the service. The service-specific module "glues" the standard modules to the PWE3 MIB modules. The next layer of the PWE3 MIB structure is the PW MIB module [RFC5601]. This module is used to configure general parameters of PWs that are common to all types of emulated services and PSNs. This layer is connected to the service-specific layer above and the PSN layer below. The PSN layer provides PSN-specific modules for each type of PSN. These modules associate the PW with one or more "tunnels" that carry the service over the PSN. These modules are used to "glue" the PW service to the underlying PSN-specific MIB modules. This document defines the MIB module for PW over MPLS PSN. [RFC5542] defines some of the object types used in these modules. 5. Features Checklist The PW-MPLS-STD-MIB module is designed to satisfy the following requirements and constraints: - The MIB module supports both manually configured and signaled PWs. - The MIB module supports point-to-point PW connections. - The MIB module enables the use of any emulated service. - The MIB module supports MPLS-TE outer tunnel, non-TE MPLS outer tunnel (an outer tunnel signaled by LDP or set up manually), and no outer tunnel (where the PW label is the only label in the MPLS stack). The latter case is applicable for manual configuration of PW over a single hop, as for signaled MPLS PSN even across a single hop there is an MPLS tunnel -- even though the actual packet may not contain the MPLS tunnel label due to PHP. The MIB module uses Textual Conventions (TCs) from [RFC2578], [RFC2579], [RFC2580], [RFC2863], [RFC3811], [RFC3813], [RFC5542], and [RFC5601]. Zelig & Nadeau Standards Track [Page 4] RFC 5602 PW MPLS MIB July 2009 6. MIB Module Usage - The PW table (pwTable) in [RFC5601] is used for all PW types (ATM, FR, Ethernet, SONET, etc.). This table contains high-level generic parameters related to the PW creation. The operator or the agent creates a row for each PW. - If the selected PSN type in the pwTable is MPLS, the agent creates a row in the MPLS-specific parameters table (pwMplsTable) in this module, which contains MPLS-specific parameters such as EXP bits handling and outer tunnel configuration. - The operator configures the association to the desired MPLS tunnel (required for MPLS-TE tunnels or for manually configured PWs) through the pwMplsTeOutboundTable. For the LDP-based outer tunnel, there is no need for manual configuration since there is only a single tunnel toward the peer. - The agent creates rows in the MPLS mapping table in order to allow quick retrieval of information based on the tunnel indexes. The relation to the MPLS network is by configuration of the edge LSR only -- i.e., the LSR that provides the PW function. Since tunnels are unidirectional, a pair of tunnels MUST exist (one for inbound, one for outbound). Figure 1 depicts a PW that originates and terminates at LSR-M. It uses tunnels A and B formed by cross- connects (XCs) Ax and Bx continuing through LSR-N to LSR-P. The concatenations of XCs create the tunnels. Note: 'X' denotes a tunnel's cross-connect. Zelig & Nadeau Standards Track [Page 5] RFC 5602 PW MPLS MIB July 2009 Tunnel A <- - - - - - - - - - - - - - - - - - - - - - - - - - - - +---- (edge) LSR-M ---+ +--------- LSR-N ---------+ + LSR-P |---+ | | | | | | XC | | XC | | + | A1 (M<-N) +----+ +----+ A2 (M<-P) +----+ +----+ | | <------| | | |<--------------| | | | <-->| N |PWin inSeg |MPLS| |MPLS| outSeg inSeg |MPLS| |MPLS| N S | | <---X<-----| IF | | IF |<------X<------| IF | | IF | A E | S | | |<-->| | | |<-->| | | T R | | --->X----->| | | |------>X------>| | | | I V | P |PWout outSeg| | | | inSeg outSeg | | | | V I | | ------>| | | |-------------->| | | | E C + | XC +----+ +----+ XC +----+ +----+ E |---+ B1 (M->N) | | B2 (M->P) | | | | | | | +---------------------+ +-------------------------+ +----- - - - - - - - - - - - - - - - - - - - - - - - - - - - -> Tunnel B Figure 1: PW modeling over MPLS The PW-MPLS-STD-MIB supports three options for an MPLS network: (1) In the MPLS-TE case, tunnels A and B are created via the MPLS- TE-STD-MIB [RFC3812]. The tunnels are associated (in each peer independently) to the PW by the four indexes that uniquely identify the tunnel at the MPLS-TE-STD-MIB. (2) In the non-TE case, tunnels A1 and B1 are either manually configured or set up with LDP. The tunnels are associated to the PW by the XC index in the MPLS-LSR-STD-MIB [RFC3813]. (3) In the PW-label-only case, there is no outer tunnel on top of the PW label. This case is useful in the case of adjacent Provider Edges (PEs) in manual configuration mode. Note that for signaled tunnels, when LSR-N acts as PHP for the outer tunnel label, there are still entries for the outer tunnel in the relevant MPLS MIB modules, so even for the case of adjacent LSRs, the relevant mode is either MPLS-TE or non-TE. A combination of MPLS-TE outer tunnel(s) and LDP outer tunnel for the same PW is allowed through the pwMplsOutboundTunnel. The current tunnel that is used to forward traffic is indicated in the object pwMplsOutboundTunnelTypeInUse. Zelig & Nadeau Standards Track [Page 6] RFC 5602 PW MPLS MIB July 2009 The PW-MPLS-STD-MIB module reports through the inbound table the XC entry in the LDP-STD-MIB [RFC3815] of the PW that was signaled through LDP. This MIB module assumes that a PW can be associated to one MPLS-TE tunnel at a time. This tunnel may be composed of multiple instances (i.e., LSP), each represented by a separate instance index. The selection of the active LSP out of the possible LSPs in the tunnel is out of the scope of this MIB module as it is part of the MPLS PSN functionality. The current active LSP is reported through this MIB module. It is important to note that inbound (tunnel originated in the remote PE) mapping is not configured or reported through the PW-MPLS-STD- MIB module since the local PE does not know the inbound association between specific PW and MPLS tunnels. 7. PW-MPLS-STD-MIB Example The following example (supplement the example provided in [RFC5601]) assumes that the node has already established the LDP tunnel to the peer node and that a PW has been configured in the pwTable in [RFC5601] with pwPsnType equal 'mpls'. The agent creates an entry in pwMplsTable with the following parameters: pwMplsMplsType mplsNonTe(1), -- LDP tunnel pwMplsExpBitsMode outerTunnel(1), -- Default pwMplsExpBits 0, -- Default pwMplsTtl 2, -- Default pwMplsLocalLdpID 192.0.2.200:0, pwMplsLocalLdpEntityIndex 1, pwMplsPeerLdpID 192.0.2.5:0, pwMplsStorageType nonVolatile(3) The agent also creates an entry in pwMplsOutboundTable for reporting the mapping of the PW on the LDP tunnel: pwMplsOutboundLsrXcIndex 100, - The XC number for the -- LDP tunnel pwMplsOutboundTunnelIndex 0, -- No TE tunnel pwMplsOutboundTunnelInstance 0, -- No TE tunnel pwMplsOutboundTunnelLclLSR 0, -- No TE tunnel pwMplsOutboundTunnelPeerLSR 0, -- No TE tunnel pwMplsOutboundIfIndex 0, -- Not applicable pwMplsOutboundTunnelTypeInUse mplsNonTe(3) Zelig & Nadeau Standards Track [Page 7] RFC 5602 PW MPLS MIB July 2009 The agent now creates entries for the PW in the following tables: - pwMplsInboundTable - pwMplsNonTeMappingTable (2 entries) To create an MPLS-TE tunnel to carry this PW, the operator takes the following steps: - Set pwMplsMplsType in pwMplsTable to both mplsNonTe(1) and mplsTe(0). - Set pwMplsOutboundTunnelIndex, pwMplsOutboundTunnelInstance, pwMplsOutboundTunnelLclLSR, and pwMplsOutboundTunnelPeerLSR in pwMplsOutboundTable to the MPLS-TE tunnel that will carry this PW. The agent will report the tunnel that the PW is currently using through pwMplsOutboundTunnelTypeInUse, and will report the PW to MPLS-TE tunnel/LSP mapping in pwMplsTeMappingTable. 8. Object Definitions PW-MPLS-STD-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, mib-2 FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC2580] StorageType FROM SNMPv2-TC -- [RFC2579] InterfaceIndexOrZero FROM IF-MIB -- [RFC2863] MplsTunnelIndex, MplsTunnelInstanceIndex, MplsLdpIdentifier, MplsLsrIdentifier FROM MPLS-TC-STD-MIB -- [RFC3811] MplsIndexType FROM MPLS-LSR-STD-MIB -- [RFC3813] PwIndexType FROM PW-TC-STD-MIB -- [RFC5542] Zelig & Nadeau Standards Track [Page 8] RFC 5602 PW MPLS MIB July 2009 pwIndex -- [RFC5601] FROM PW-STD-MIB ; pwMplsStdMIB MODULE-IDENTITY LAST-UPDATED "200906120000Z" -- 12 June 2009 00:00:00 GMT ORGANIZATION "Pseudowire Emulation Edge-to-Edge (PWE3) Working Group." CONTACT-INFO " David Zelig, Editor Email: davidz@corrigent.com Thomas D. Nadeau, Editor Email: tom.nadeau@bt.com The PWE3 Working Group (email distribution pwe3@ietf.org, http://www.ietf.org/html.charters/pwe3-charter.html) " DESCRIPTION "This MIB module complements the PW-STD-MIB module for PW operation over MPLS. Copyright (c) 2009 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. - Neither the name of Internet Society, IETF or IETF Trust, nor the names of specific contributors, may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE Zelig & Nadeau Standards Track [Page 9] RFC 5602 PW MPLS MIB July 2009 DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This version of this MIB module is part of RFC 5602; see the RFC itself for full legal notices. " -- Revision history. REVISION "200906120000Z" -- 12 June 2009 00:00:00 GMT DESCRIPTION "First published as RFC 5602. " ::= { mib-2 181 } -- Top-level components of this MIB. -- Notifications pwMplsNotifications OBJECT IDENTIFIER ::= { pwMplsStdMIB 0 } -- Tables, Scalars pwMplsObjects OBJECT IDENTIFIER ::= { pwMplsStdMIB 1 } -- Conformance pwMplsConformance OBJECT IDENTIFIER ::= { pwMplsStdMIB 2 } -- PW MPLS table pwMplsTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table controls MPLS-specific parameters when the PW is going to be carried over MPLS PSN." ::= { pwMplsObjects 1 } pwMplsEntry OBJECT-TYPE SYNTAX PwMplsEntry MAX-ACCESS not-accessible Zelig & Nadeau Standards Track [Page 10] RFC 5602 PW MPLS MIB July 2009 STATUS current DESCRIPTION "A row in this table represents parameters specific to MPLS PSN for a pseudowire (PW). The row is created automatically by the local agent if the pwPsnType is mpls(1). It is indexed by pwIndex, which uniquely identifies a singular PW. Manual entries in this table SHOULD be preserved after a reboot, and the agent MUST ensure the integrity of those entries. If the set of entries of a specific row were found to be nonconsistent after reboot, the PW pwOperStatus MUST be declared as down(2). Any read-write object in this table MAY be changed at any time; however, change of some objects (for example, pwMplsMplsType) during PW forwarding state MAY cause traffic disruption." INDEX { pwIndex } ::= { pwMplsTable 1 } PwMplsEntry ::= SEQUENCE { pwMplsMplsType BITS, pwMplsExpBitsMode INTEGER, pwMplsExpBits Unsigned32, pwMplsTtl Unsigned32, pwMplsLocalLdpID MplsLdpIdentifier, pwMplsLocalLdpEntityIndex Unsigned32, pwMplsPeerLdpID MplsLdpIdentifier, pwMplsStorageType StorageType } pwMplsMplsType OBJECT-TYPE SYNTAX BITS { mplsTe (0), mplsNonTe (1), pwOnly (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is set by the operator to indicate the outer tunnel types, if existing. mplsTe(0) is used if the outer tunnel is set up by MPLS-TE, and mplsNonTe(1) is used if the outer tunnel is set up by LDP or manually. A combination of mplsTe(0) and mplsNonTe(1) MAY exist. pwOnly(2) is used if there is no outer tunnel label, i.e., Zelig & Nadeau Standards Track [Page 11] RFC 5602 PW MPLS MIB July 2009 in static provisioning without an MPLS tunnel. pwOnly(2) cannot be combined with mplsNonTe(1) or mplsTe(0). An implementation that can identify automatically that the peer node is directly connected MAY support the bit pwOnly(2) as read-only. " DEFVAL { { mplsNonTe } } ::= { pwMplsEntry 1 } pwMplsExpBitsMode OBJECT-TYPE SYNTAX INTEGER { outerTunnel (1), specifiedValue (2), serviceDependant (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is set by the operator to determine the PW shim label EXP bits. The value of outerTunnel(1) is used where there is an outer tunnel -- pwMplsMplsType equals to mplsTe(0) or mplsNonTe(1). Note that in this case, there is no need to mark the PW label with the EXP bits, since the PW label is not visible to the intermediate nodes. If there is no outer tunnel, specifiedValue(2) SHOULD be used to indicate that the value is specified by pwMplsExpBits. Setting serviceDependant(3) indicates that the EXP bits are set based on a rule that is implementation specific." DEFVAL { outerTunnel } ::= { pwMplsEntry 2 } pwMplsExpBits OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is set by the operator if pwMplsExpBitsMode is set to specifiedValue(2) to indicate the MPLS EXP bits to be used on the PW shim label. Otherwise, it SHOULD be set to zero." DEFVAL { 0 } ::= { pwMplsEntry 3 } pwMplsTtl OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write Zelig & Nadeau Standards Track [Page 12] RFC 5602 PW MPLS MIB July 2009 STATUS current DESCRIPTION "This object is set by the operator to indicate the PW TTL value to be used on the PW shim label." DEFVAL { 2 } ::= { pwMplsEntry 4 } pwMplsLocalLdpID OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "The LDP identifier of the LDP entity that creates this PW in the local node. As the PW labels are always set from the per-platform label space, the last two octets in the LDP ID MUST always both be zeros." REFERENCE "'LDP specifications', RFC 3036, section 2.2.2." ::= { pwMplsEntry 5 } pwMplsLocalLdpEntityIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The local node LDP Entity Index of the LDP entity creating this PW." ::= { pwMplsEntry 6 } pwMplsPeerLdpID OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The peer LDP identifier of the LDP session. This object SHOULD return the value zero if LDP is not used or if the value is not yet known." ::= { pwMplsEntry 7 } pwMplsStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates the storage type for this row." DEFVAL { nonVolatile } ::= { pwMplsEntry 8 } Zelig & Nadeau Standards Track [Page 13] RFC 5602 PW MPLS MIB July 2009 -- End of PW MPLS Table -- Pseudowire MPLS Outbound Tunnel Table pwMplsOutboundTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsOutboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table reports and configures the current outbound MPLS tunnels (i.e., toward the PSN) or the physical interface in the case of a PW label only that carries the PW traffic. It also reports the current outer tunnel and LSP that forward the PW traffic." ::= { pwMplsObjects 2 } pwMplsOutboundEntry OBJECT-TYPE SYNTAX PwMplsOutboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table configures the outer tunnel used for carrying the PW traffic toward the PSN. In the case of PW label only, it configures the interface that will carry the PW traffic. An entry in this table augments the pwMplsEntry, and is created automatically when the corresponding row has been created by the agent in the pwMplsEntry. This table points to the appropriate MPLS MIB module: In the MPLS-TE case, the three objects relevant to the indexing of a TE tunnel head-end (as used in the MPLS-TE-STD-MIB) are to be configured, and the tunnel instance indicates the LSP that is currently in use for forwarding the traffic. In the case of signaled non-TE MPLS (an outer tunnel label assigned by LDP), the table points to the XC entry in the LSR-STD-MIB. If the non-TE MPLS tunnel is manually configured, the operator configures the XC pointer to this tunnel. In the case of PW label only (no outer tunnel), the ifIndex of the port to carry the PW is configured here. Zelig & Nadeau Standards Track [Page 14] RFC 5602 PW MPLS MIB July 2009 It is possible to associate a PW to one TE tunnel head-end and a non-TE tunnel together. An indication in this table will report the currently active one. In addition, in the TE case, the table reports the active tunnel instance (i.e., the specific LSP in use). Any read-write object in this table MAY be changed at any time; however, change of some objects (for example, MPLS-TE indexes) during PW forwarding state MAY cause traffic disruption." AUGMENTS { pwMplsEntry } ::= { pwMplsOutboundTable 1 } PwMplsOutboundEntry ::= SEQUENCE { pwMplsOutboundLsrXcIndex MplsIndexType, pwMplsOutboundTunnelIndex MplsTunnelIndex, pwMplsOutboundTunnelInstance MplsTunnelInstanceIndex, pwMplsOutboundTunnelLclLSR MplsLsrIdentifier, pwMplsOutboundTunnelPeerLSR MplsLsrIdentifier, pwMplsOutboundIfIndex InterfaceIndexOrZero, pwMplsOutboundTunnelTypeInUse INTEGER } pwMplsOutboundLsrXcIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if the pwMplsMplsType mplsNonTe(1) bit is set, and MUST return a value of zero otherwise. If the outer tunnel is signaled, the object is read-only and indicates the XC index in the MPLS-LSR-STD-MIB of the outer tunnel toward the peer. Otherwise (tunnel is set up manually), the operator defines the XC index of the manually created outer tunnel through this object. " ::= { pwMplsOutboundEntry 1 } pwMplsOutboundTunnelIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if the pwMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. It is part of the set of indexes for the outbound tunnel. Zelig & Nadeau Standards Track [Page 15] RFC 5602 PW MPLS MIB July 2009 The operator sets this object to represent the desired tunnel head-end toward the peer for carrying the PW traffic. " ::= { pwMplsOutboundEntry 2 } pwMplsOutboundTunnelInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object is applicable if the pwMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. It indicates the actual tunnel instance that is currently active and carrying the PW traffic. It SHOULD return the value zero if the information from the MPLS-TE application is not yet known. " ::= { pwMplsOutboundEntry 3 } pwMplsOutboundTunnelLclLSR OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if the pwMplsMplsType mplsTe(0) bit is set, and MUST return a value of all zeros otherwise. It is part of the set of indexes for the outbound tunnel. The operator sets this object to represent the desired tunnel head-end toward the peer for carrying the PW traffic. " ::= { pwMplsOutboundEntry 4 } pwMplsOutboundTunnelPeerLSR OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if the pwMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. It is part of the set of indexes for the outbound tunnel. Note that in most cases, it equals to pwPeerAddr. " ::= { pwMplsOutboundEntry 5 } pwMplsOutboundIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero Zelig & Nadeau Standards Track [Page 16] RFC 5602 PW MPLS MIB July 2009 MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if the pwMplsMplsType pwOnly(0) bit is set, and MUST return a value of zero otherwise. The operator configures the ifIndex of the outbound port in this case. " ::= { pwMplsOutboundEntry 6 } pwMplsOutboundTunnelTypeInUse OBJECT-TYPE SYNTAX INTEGER { notYetKnown (1), mplsTe (2), mplsNonTe (3), pwOnly (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current tunnel that is carrying the PW traffic. The value of notYetKnown(1) should be used if the agent is currently unable to determine which tunnel or interface is carrying the PW, for example, because both tunnels are in operational status down. " ::= { pwMplsOutboundEntry 7 } -- End of PW MPLS Outbound Tunnel table -- PW MPLS inbound table pwMplsInboundTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsInboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the PW LDP XC entry in the MPLS-LSR-STD-MIB for signaled PWs. " ::= { pwMplsObjects 3 } pwMplsInboundEntry OBJECT-TYPE SYNTAX PwMplsInboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION Zelig & Nadeau Standards Track [Page 17] RFC 5602 PW MPLS MIB July 2009 "A row in this table is created by the agent for each signaled PW, and shows the XC index related to the PW signaling in the inbound direction in the MPLS-LSR-STD-MIB that controls and display the information for all the LDP signaling processes in the local node. " INDEX { pwIndex } ::= { pwMplsInboundTable 1 } PwMplsInboundEntry ::= SEQUENCE { pwMplsInboundXcIndex MplsIndexType } pwMplsInboundXcIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The XC index representing this PW in the inbound direction. It MUST return the value zero if the information is not yet known." ::= { pwMplsInboundEntry 1 } -- End of PW MPLS inbound table -- PW to Non-TE mapping Table. pwMplsNonTeMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsNonTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the PW association to the outbound tunnel in non-TE applications, maps the PW to its (inbound) XC entry, and indicates the PW-to-physical interface mapping for a PW without an outer tunnel. " ::= { pwMplsObjects 4 } pwMplsNonTeMappingEntry OBJECT-TYPE SYNTAX PwMplsNonTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table displays the association between the PW and - its non-TE MPLS outbound outer tunnel, Zelig & Nadeau Standards Track [Page 18] RFC 5602 PW MPLS MIB July 2009 - its XC entry in the MPLS-LSR-STD-MIB, or - its physical interface if there is no outer tunnel (PW label only) and manual configuration. Rows are created in this table by the agent depending on the setting of pwMplsMplsType: - If the pwMplsMplsType mplsNonTe(1) bit is set, the agent creates a row for the outbound direction (pwMplsNonTeMappingDirection set to psnBound(1)). The pwMplsNonTeMappingXcIndex holds the XC index in the MPLS-LSR-STD-MIB of the PSN-bound outer tunnel. pwMplsNonTeMappingIfIndex MUST be zero for this row. - If the pwMplsMplsType pwOnly(2) bit is set, the agent creates a row for the outbound direction (pwMplsNonTeMappingDirection set to psnBound(1)). The pwMplsNonTeMappingIfIndex holds the ifIndex of the physical port this PW will use in the outbound direction. pwMplsNonTeMappingXcIndex MUST be zero for this row. - If the PW has been set up by a signaling protocol (i.e., pwOwner equal pwIdFecSignaling(2) or genFecSignaling(3)), the agent creates a row for the inbound direction (pwMplsNonTeMappingDirection set to fromPsn(2)). The pwMplsNonTeMappingXcIndex holds the XC index in the MPLS-LSR-STD-MIB of the PW LDP-generated XC entry. pwMplsNonTeMappingIfIndex MUST be zero for this row. An application can use this table to quickly retrieve the PW carried over specific non-TE MPLS outer tunnel or physical interface. " INDEX { pwMplsNonTeMappingDirection, pwMplsNonTeMappingXcIndex, pwMplsNonTeMappingIfIndex, pwMplsNonTeMappingPwIndex } ::= { pwMplsNonTeMappingTable 1 } PwMplsNonTeMappingEntry ::= SEQUENCE { pwMplsNonTeMappingDirection INTEGER, pwMplsNonTeMappingXcIndex MplsIndexType, pwMplsNonTeMappingIfIndex InterfaceIndexOrZero, pwMplsNonTeMappingPwIndex PwIndexType } Zelig & Nadeau Standards Track [Page 19] RFC 5602 PW MPLS MIB July 2009 pwMplsNonTeMappingDirection OBJECT-TYPE SYNTAX INTEGER { psnBound (1), fromPsn (2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for the conceptual XC row identifying the tunnel-to-PW mappings, indicating the direction of the packet flow for this entry. psnBound(1) indicates that the entry is related to packets toward the PSN. fromPsn(2) indicates that the entry is related to packets coming from the PSN. " ::= { pwMplsNonTeMappingEntry 1 } pwMplsNonTeMappingXcIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "See the description clause of pwMplsNonTeMappingEntry for the usage guidelines of this object." ::= { pwMplsNonTeMappingEntry 2 } pwMplsNonTeMappingIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "See the description clause of pwMplsNonTeMappingEntry for the usage guidelines of this object." ::= { pwMplsNonTeMappingEntry 3 } pwMplsNonTeMappingPwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The value that represents the PW in the pwTable." ::= { pwMplsNonTeMappingEntry 4 } -- End of PW to Non-TE mapping Table. -- PW to TE MPLS tunnels mapping Table. Zelig & Nadeau Standards Track [Page 20] RFC 5602 PW MPLS MIB July 2009 pwMplsTeMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table reports the PW association to the outbound MPLS tunnel for MPLS-TE applications." ::= { pwMplsObjects 5 } pwMplsTeMappingEntry OBJECT-TYPE SYNTAX PwMplsTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents the association between a PW and its MPLS-TE outer (head-end) tunnel. An application can use this table to quickly retrieve the list of the PWs that are configured on a specific MPLS-TE outer tunnel. The pwMplsTeMappingTunnelInstance reports the actual LSP out of the tunnel head-end that is currently forwarding the traffic. The table is indexed by the head-end indexes of a TE tunnel and the PW index. " INDEX { pwMplsTeMappingTunnelIndex, pwMplsTeMappingTunnelInstance, pwMplsTeMappingTunnelPeerLsrID, pwMplsTeMappingTunnelLocalLsrID, pwMplsTeMappingPwIndex } ::= { pwMplsTeMappingTable 1 } PwMplsTeMappingEntry ::= SEQUENCE { pwMplsTeMappingTunnelIndex MplsTunnelIndex, pwMplsTeMappingTunnelInstance MplsTunnelInstanceIndex, pwMplsTeMappingTunnelPeerLsrID MplsLsrIdentifier, pwMplsTeMappingTunnelLocalLsrID MplsLsrIdentifier, pwMplsTeMappingPwIndex PwIndexType } Zelig & Nadeau Standards Track [Page 21] RFC 5602 PW MPLS MIB July 2009 pwMplsTeMappingTunnelIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index for the conceptual row identifying the MPLS-TE tunnel that is carrying the PW traffic." ::= { pwMplsTeMappingEntry 1 } pwMplsTeMappingTunnelInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the MPLS-TE LSP that is carrying the PW traffic. It MUST return the value zero if the information of the specific LSP is not yet known. Note that based on the recommendation in the MPLS-TC-STD-MIB, instance index 0 should refer to the configured tunnel interface." ::= { pwMplsTeMappingEntry 2 } pwMplsTeMappingTunnelPeerLsrID OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the peer LSR when the outer tunnel is MPLS-TE." ::= { pwMplsTeMappingEntry 3 } pwMplsTeMappingTunnelLocalLsrID OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the local LSR." ::= { pwMplsTeMappingEntry 4 } pwMplsTeMappingPwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the value that represents the PW in the pwTable." ::= { pwMplsTeMappingEntry 5 } Zelig & Nadeau Standards Track [Page 22] RFC 5602 PW MPLS MIB July 2009 -- End of PW to TE MPLS tunnels mapping Table. -- conformance information pwMplsGroups OBJECT IDENTIFIER ::= { pwMplsConformance 1 } pwMplsCompliances OBJECT IDENTIFIER ::= { pwMplsConformance 2 } -- Compliance requirement for fully compliant implementations. pwMplsModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide full support for the PW-MPLS-STD-MIB module. Such devices can then be monitored and also be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwMplsGroup, pwMplsOutboundMainGroup, pwMplsInboundGroup, pwMplsMappingGroup } GROUP pwMplsOutboundTeGroup DESCRIPTION "This group MUST be supported if the implementation allows MPLS-TE tunnels to carry PW traffic. " OBJECT pwMplsMplsType DESCRIPTION "Support of pwOnly(2) is not required. At least one of mplsTe(0) or mplsNonTe(1) MUST be supported if signaling of PW is supported. " OBJECT pwMplsExpBitsMode DESCRIPTION "Support of specifiedValue(2) and serviceDependant(3) is optional. " OBJECT pwMplsLocalLdpID MIN-ACCESS read-only DESCRIPTION "A read-write access is required if the implementation supports more than one LDP entity identifier for PW signaling. " OBJECT pwMplsLocalLdpEntityIndex Zelig & Nadeau Standards Track [Page 23] RFC 5602 PW MPLS MIB July 2009 MIN-ACCESS read-only DESCRIPTION "A read-write access is required if the implementation supports more than one LDP entity index for PW signaling. " OBJECT pwMplsOutboundLsrXcIndex MIN-ACCESS read-only DESCRIPTION "A value other than zero MUST be supported if the implementation supports non-TE signaling of the outer tunnel. A read-write access MUST be supported if the implementation supports PW label manual setting and carrying them over non-TE tunnels. " OBJECT pwMplsOutboundIfIndex MIN-ACCESS read-only DESCRIPTION "A value other than zero and read-write operations MUST be supported if the implementation supports manually configured PW without MPLS outer tunnel. " ::= { pwMplsCompliances 1 } -- Compliance requirement for Read Only compliant implementations. pwMplsModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide read- only support for the PW-MPLS-STD-MIB module. Such devices can then be monitored but cannot be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwMplsGroup, pwMplsOutboundMainGroup, pwMplsInboundGroup, pwMplsMappingGroup } GROUP pwMplsOutboundTeGroup DESCRIPTION "This group MUST be supported if the implementation allows MPLS-TE tunnels to carry PW traffic. " OBJECT pwMplsMplsType MIN-ACCESS read-only Zelig & Nadeau Standards Track [Page 24] RFC 5602 PW MPLS MIB July 2009 DESCRIPTION "Write access is not required. Support of pwOnly(2) is not required. At least one of mplsTe(0) or mplsNonTe(1) MUST be supported if signaling of PW is supported. " OBJECT pwMplsExpBitsMode MIN-ACCESS read-only DESCRIPTION "Write access is not required. Support of specifiedValue(2) and serviceDependant(3) is optional. " OBJECT pwMplsExpBits MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsTtl MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsLocalLdpID MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsLocalLdpEntityIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsOutboundLsrXcIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. A value other than zero MUST be supported if the implementation supports non-TE signaling of the outer tunnel. " OBJECT pwMplsOutboundTunnelIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. " Zelig & Nadeau Standards Track [Page 25] RFC 5602 PW MPLS MIB July 2009 OBJECT pwMplsOutboundTunnelLclLSR MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsOutboundTunnelPeerLSR MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsOutboundIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. A value other than zero MUST be supported if the implementation supports manually configured PW without MPLS outer tunnel. " ::= { pwMplsCompliances 2 } -- Units of conformance. pwMplsGroup OBJECT-GROUP OBJECTS { pwMplsMplsType, pwMplsExpBitsMode, pwMplsExpBits, pwMplsTtl, pwMplsLocalLdpID, pwMplsLocalLdpEntityIndex, pwMplsPeerLdpID, pwMplsStorageType } STATUS current DESCRIPTION "Collection of objects needed for PW over MPLS PSN configuration." ::= { pwMplsGroups 1 } pwMplsOutboundMainGroup OBJECT-GROUP OBJECTS { pwMplsOutboundLsrXcIndex, pwMplsOutboundIfIndex, pwMplsOutboundTunnelTypeInUse } STATUS current DESCRIPTION Zelig & Nadeau Standards Track [Page 26] RFC 5602 PW MPLS MIB July 2009 "Collection of objects needed for outbound association of PW and MPLS tunnel." ::= { pwMplsGroups 2 } pwMplsOutboundTeGroup OBJECT-GROUP OBJECTS { pwMplsOutboundTunnelIndex, pwMplsOutboundTunnelInstance, pwMplsOutboundTunnelLclLSR, pwMplsOutboundTunnelPeerLSR } STATUS current DESCRIPTION "Collection of objects needed for outbound association of PW and MPLS-TE tunnel." ::= { pwMplsGroups 3 } pwMplsInboundGroup OBJECT-GROUP OBJECTS { pwMplsInboundXcIndex } STATUS current DESCRIPTION "Collection of objects needed for inbound PW presentation. This group MUST be supported if PW signaling through LDP is used." ::= { pwMplsGroups 4 } pwMplsMappingGroup OBJECT-GROUP OBJECTS { pwMplsNonTeMappingPwIndex, pwMplsTeMappingPwIndex } STATUS current DESCRIPTION "Collection of objects needed for mapping association of PW and MPLS tunnel." ::= { pwMplsGroups 5 } END Zelig & Nadeau Standards Track [Page 27] RFC 5602 PW MPLS MIB July 2009 9. Security Considerations It is clear that this MIB module is potentially useful for monitoring PW-capable PEs. This MIB module can also be used for configuration of certain objects, and anything that can be configured can be incorrectly configured, with potentially disastrous results. There are number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: o the pwMplsTable, pwMplsNonTeMappingTable and pwMplsTeMappingTable collectively contain objects to provision PW over MPLS tunnels. Unauthorized access to objects in these tables, could result in disruption of traffic on the network. The use of stronger mechanisms such as SNMPv3 security should be considered where possible. Specifically, SNMPv3 VACM and USM MUST be used with any v3 agent which implements this MIB module. Administrators should consider whether read access to these objects should be allowed, since read access may be undesirable under certain circumstances. Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: o the pwMplsTable, pwMplsNonTeMappingTable, pwMplsTeMappingTable and pwMplsOutboundTable collectively show the PW over MPLS association. If an Administrator does not want to reveal this information, then these tables should be considered sensitive/ vulnerable. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. Zelig & Nadeau Standards Track [Page 28] RFC 5602 PW MPLS MIB July 2009 It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module, is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 10. IANA Considerations The MIB module in this document uses the following IANA-assigned OBJECT IDENTIFIER values recorded in the SMI Numbers registry: Descriptor OBJECT IDENTIFIER value ---------- ----------------------- pwMplsStdMIB { mib-2 181 } 11. References 11.1. Normative References [BCP14] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [RFC3031] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol Label Switching Architecture", RFC 3031, January 2001. Zelig & Nadeau Standards Track [Page 29] RFC 5602 PW MPLS MIB July 2009 [RFC3811] Nadeau, T., Ed., and J. Cucchiara, Ed., "Definitions of Textual Conventions (TCs) for Multiprotocol Label Switching (MPLS) Management", RFC 3811, June 2004. [RFC3812] Srinivasan, C., Viswanathan, A., and T. Nadeau, "Multiprotocol Label Switching (MPLS) Traffic Engineering (TE) Management Information Base (MIB)", RFC 3812, June 2004. [RFC3813] Srinivasan, C., Viswanathan, A., and T. Nadeau, "Multiprotocol Label Switching (MPLS) Label Switching Router (LSR) Management Information Base (MIB)", RFC 3813, June 2004. [RFC4447] Martini, L., Ed., Rosen, E., El-Aawar, N., Smith, T., and G. Heron, "Pseudowire Setup and Maintenance Using the Label Distribution Protocol (LDP)", RFC 4447, April 2006. [RFC5542] Nadeau, T., Ed., Zelig, D., Ed., and O. Nicklass, Ed., "Definitions of Textual Conventions for Pseudowire (PW) Management", RFC 5542, May 2009. [RFC5601] Nadeau, T., Ed. and D. Zelig, Ed. "Pseudowire (PW) Management Information Base (MIB)", RFC 5601, July 2009. 11.2. Informative References [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, December 2002. [RFC3815] Cucchiara, J., Sjostrand, H., and J. Luciani, "Definitions of Managed Objects for the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP)", RFC 3815, June 2004. [RFC3916] Xiao, X., Ed., McPherson, D., Ed., and P. Pate, Ed., "Requirements for Pseudo-Wire Emulation Edge-to-Edge (PWE3)", RFC 3916, September 2004. [RFC3985] Bryant, S., Ed., and P. Pate, Ed., "Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture", RFC 3985, March 2005. Zelig & Nadeau Standards Track [Page 30] RFC 5602 PW MPLS MIB July 2009 Authors' Addresses David Zelig (editor) Oversi Networks 1 Rishon Letzion St. Petah Tikva Israel Phone: +972 77 3337 750 EMail: davidz@oversi.com Thomas D. Nadeau (editor) BT BT Centre 81 Newgate Street London EC1A 7AJ United Kingdom EMail: tom.nadeau@bt.com Zelig & Nadeau Standards Track [Page 31]