Network Working Group                                          A. Newton
Request for Comments: 4993                                VeriSign, Inc.
Category: Standards Track                                    August 2007


                  A Lightweight UDP Transfer Protocol
             for the Internet Registry Information Service

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The IETF Trust (2007).

Abstract

   This document describes a lightweight UDP transfer protocol for the
   Internet Registry Information Service (IRIS).  This transfer protocol
   uses a single packet for every request and response, and optionally
   employs compression over the contents of the packet.

























Newton                      Standards Track                     [Page 1]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


Table of Contents

   1. Introduction ....................................................3
   2. Document Terminology ............................................3
   3. Packet Format ...................................................4
      3.1. Payload Descriptor .........................................4
           3.1.1. Payload Request Descriptor ..........................4
           3.1.2. Payload Response Descriptor .........................5
           3.1.3. Payload Header ......................................6
           3.1.4. Payload Types .......................................6
           3.1.5. Version Information .................................7
           3.1.6. Size Information ....................................8
           3.1.7. Other Information ...................................8
   4. Interactions ....................................................9
   5. Internationalization Considerations ............................10
   6. IRIS Transport Mapping Definitions .............................10
      6.1. URI Scheme ................................................10
      6.2. Application Protocol Label ................................10
   7. IANA Considerations ............................................10
      7.1. Registrations .............................................10
           7.1.1. URI Scheme Registration ............................10
           7.1.2. Well-known UDP Port Registration ...................11
           7.1.3. S-NAPTR Registration ...............................11
   8. Security Considerations ........................................12
   9. References .....................................................13
      9.1. Normative References ......................................13
      9.2. Informative References ....................................13
   Appendix A. Examples ..............................................14
   Appendix B. Contributors ..........................................18






















Newton                      Standards Track                     [Page 2]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


1.  Introduction

   Using Straightforward Name Authority Pointers (S-NAPTR) [4], IRIS has
   the ability to define the use of multiple application transports or
   transfer protocols for different types of registry services, all at
   the discretion of the server operator.  The UDP transfer protocol
   defined in this document is completely independent of the registry
   types for which it can carry data.

   The binding of this UDP transfer protocol to IRIS is called IRIS-LWZ
   (for IRIS Lightweight using Compression).  Its message exchange
   pattern is simple: a client sends a request in one UDP packet, and a
   server responds with an answer in one UDP packet.

   IRIS-LWZ packets are composed of two parts, a binary payload
   descriptor and a request/response transaction payload.  The request/
   response transaction payload may be compressed using the DEFLATE [1]
   algorithm.

2.  Document Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [6].

   Octet fields with numeric values are given according to the
   conventions in RFC 1166 [10]: the leftmost bit of the whole field is
   the most significant bit; when a multi-octet quantity is transmitted
   the most significant octet is transmitted first.  Bits signifying
   flags in an octet are numbered according to the conventions of RFC
   1166 [10]: bit 0 is the most significant bit and bit 7 is the least
   significant bit.  When a diagram describes a group of octets, the
   order of transmission for the octets starts from the left.


















Newton                      Standards Track                     [Page 3]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


3.  Packet Format

   The packet format for IRIS-LWZ is as follows:

         +------------+---------+
   field |  payload   | payload |
         | descriptor |         |
         +------------+---------+
   octets 3 or 6..261*    0..n

     * In request packets, the payload descriptor can vary in length
       from 6 to 261 octets (i.e., 6..261).  In response packets, the
       payload descriptor is always 3 octets.

                                IRIS-LWZ Packet

       Each IRIS-LWZ query or response is contained in a single UDP
       packet.  Servers MUST be prepared to accept packets as large as
       4000 octets, and clients MUST NOT send packets larger than 4000
       octets.

3.1.  Payload Descriptor

       The payload descriptor has two different formats, one for a
       request and one for a response.  However, each format shares a
       common 1-octet payload header described in Section 3.1.3.

3.1.1.  Payload Request Descriptor

       The payload descriptor for request packets varies from 6 to 261
       octets in length and has the following format:

             +--------+-------------+----------+-----------+-----------+
       field | header | transaction | maximum  | authority | authority |
             |        |     ID      | response |  length   |           |
             |        |             | length   |           |           |
             +--------+-------------+----------+-----------+-----------+
       octets    1           2           2           1         0..255

                          Request Payload Descriptor

       These fields have the following meanings:

       o  header - as described in Section 3.1.3.

   o  transaction ID - a 16-bit value identifying the transaction.  This
      value will be returned in the payload response descriptor (Section
      3.1.2) and can be used by clients to match requests with



Newton                      Standards Track                     [Page 4]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


      responses.  Clients SHOULD NOT use sequential values (see Section
      8).  Clients MUST NOT set all the bits in this value to 1 (i.e.,
      use a value of 0xFFFF).

   o  maximum response length - the total length of the UDP packet
      (i.e., UDP header length + payload descriptor length + XML payload
      length) that should not be exceeded when responding to this
      request.  If the server cannot provide a response that is equal to
      or less than this value, then it MUST respond with size
      information (Section 3.1.6).

   o  authority length - the length of the authority field in this
      payload descriptor.

   o  authority - a string of octets describing the authority against
      which this request is to be executed.  See [3] for the definition
      and description of an authority.  The number of octets in this
      string MUST be no more and no less than the number specified by
      the authority length.

3.1.2.  Payload Response Descriptor

   The payload descriptor for response packets is always 3 octets and
   consists of a payload header (Section 3.1.3) and a transaction ID.

         +--------+-------------+
   field | header | transaction |
         |        |     ID      |
         +--------+-------------+
   octets    1           2

                        Payload Response Descriptor

   The purpose of the transaction ID is to allow clients to match
   requests to responses.  A value of 0xFFFF is reserved for server use.
   The value of the transaction ID is as follows:

   1.  If the transaction ID in the corresponding request could not be
       read due to truncation, servers MUST use a transaction ID with
       all bits set to 1 (i.e., a value of OxFFFF) and send a descriptor
       error (see Section 3.1.7).

   2.  If the transaction ID in the corresponding request is a value of
       0xFFFF, servers MUST use a transaction ID of 0xFFFF and send a
       descriptor error (see Section 3.1.7).

   3.  Otherwise, the transaction ID MUST be the value of the
       transaction ID of the corresponding request.



Newton                      Standards Track                     [Page 5]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


3.1.3.  Payload Header

   The bits of the payload header are ordered according to RFC 1166
   [10], where bit 0 is the most significant and bit 7 is the least
   significant.  Each bit in the 1-octet payload header has the
   following meaning:

   o  bits 0 and 1 - version number ('V' field) - If 0 (both bits are
      zero), the protocol is the version defined in this document.
      Otherwise, the rest of the bits in the header and the payload may
      be interpreted as another version.

   o  bit 2 - request/response flag ('RR' flag) - If 0, this packet is a
      request (Section 3.1.1) packet.  If 1, this packet is a response
      (Section 3.1.2) packet.

   o  bits 3 - payload deflated ('PD' flag) - If 1, the payload is
      compressed using the DEFLATE [1] algorithm.

   o  bit 4 - deflate supported ('DS' flag) - If 1, the sender of this
      packet supports compression using the DEFLATE algorithm.  When
      this bit is 0 in a request, the payload of the response MUST NOT
      be compressed with DEFLATE.

   o  bit 5 - reserved - This MUST be 0.

   o  bits 6 and 7 - The value of these bits indicates payload types
      (Section 3.1.4) ('PT' field).

3.1.4.  Payload Types

   A payload type indicates the type of content in the UDP packet
   following the payload descriptor.  Some payload types have no meaning
   in request packets, and some payload types differ in meaning between
   requests and responses.  Some payload types indicate an empty
   payload.

   The payload type values in binary are as follows:

      00 - xml payload ('xml' type).  The payload is either an IRIS-
      based XML request or an IRIS-based XML response.

      01 - version info ('vi' type).  In a request packet, this payload
      type indicates that the server is to respond with version
      information (Section 3.1.5), and that the payload is empty.  In a
      response packet, this payload type indicates that the payload is
      version information (Section 3.1.5).




Newton                      Standards Track                     [Page 6]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


      10 - size info ('si' type).  This payload type has no meaning in a
      request packet and is a descriptor error.  In a response packet,
      this payload type indicates that the payload is size information
      (Section 3.1.6).

      11 - other info ('oi' type).  This payload type has no meaning in
      a request packet and is a descriptor error.  In a response packet,
      this payload type indicates that the payload is other information
      (Section 3.1.7).

3.1.5.  Version Information

   A payload type with version information ('vi') MUST be conformant to
   the XML defined in [8] and use the <versions> element as the root
   element.

   In the context of IRIS-LWZ, the protocol identifiers for these
   elements are as follows:

      <transferProtocol> - the value "iris.lwz1" to indicate the
      protocol specified in this document.

      <application> - the XML namespace identifier for IRIS [3].

      <dataModel> - the XML namespace identifier for IRIS registries.

   This document defines no extension identifiers and no authentication
   mechanism identifiers.

   Servers SHOULD send version information in the following cases:

   1.  In response to a version information request (i.e., the PT field
       is set to 'vi').

   2.  The version in a payload descriptor header does not match a
       version the server supports.

   3.  The IRIS-based XML payload does not match a version the server
       supports.

   The protocols identified by the <transferProtocol> element MUST only
   indicate protocols running on the same socket as the sender of the
   corresponding response.  In other words, while a server operator may
   also be running IRIS-XPC [9], this XML instance is only intended to
   describe version negotiation for IRIS-LWZ.






Newton                      Standards Track                     [Page 7]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


   The octet size for the 'requestSizeOctets' and 'responseSizeOctets'
   attributes of the <tranferProtocol> element are defined in Section
   3.1.6.

3.1.6.  Size Information

   A payload type with size information ('si') MUST be conformant to the
   XML defined in [8] and use the <size> element as the root element.

   Octet counts provided by this information are defined as the total
   length of the UDP packet (i.e., UDP header length + payload
   descriptor length + XML payload length).

3.1.7.  Other Information

   A payload type with other information ('oi') MUST be conformant to
   the XML defined in [8] and use the <other> element as the root
   element.

   The values for the 'type' attribute of <other> are as follows:

      'descriptor-error' - indicates there was an error decoding the
      descriptor.  Servers SHOULD send a descriptor error in the
      following cases:

      1.  When a request is received with a payload type indicating size
          information (i.e., the PT field is 'si').

      2.  When a request is received with a payload type indicating
          other information (i.e., the PT field is 'oi').

      3.  When a request is sent with a transaction ID of 0xFFFF (which
          is reserved for server use).

      4.  When a request is received with an incomplete or truncated
          payload descriptor.

      5.  When reserved bits in the payload descriptor are set to values
          other than zero.

      'payload-error' - indicates there was an error interpreting the
      payload.  Servers MUST send a payload error if they receive XML
      (i.e., the PT field is set to 'xml') and the XML cannot be parsed.

      'system-error' - indicates that the receiver cannot process the
      request due to a condition not related to this protocol.  Servers
      SHOULD send a system-error when they are capable of responding to
      requests but not capable of processing requests.



Newton                      Standards Track                     [Page 8]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


      'authority-error' - indicates that the intended authority
      specified in the corresponding request is not served by the
      receiver.  Servers SHOULD send an authority error when they
      receive a request directed to an authority other than those they
      serve.

      'no-inflation-support-error' - indicates that the receiver does
      not support payloads that have been compressed with DEFLATE [1].
      Servers MUST send this error when they receive a request that has
      been compressed with DEFLATE but they do not support inflation.

4.  Interactions

   The intent of IRIS-LWZ is to utilize UDP for IRIS requests and
   responses when UDP is appropriate.  Not all IRIS requests and
   responses will be able to utilize UDP and may require the use of
   other transfer protocols (i.e., IRIS-XPC [9] and/or Blocks Extensible
   Exchange Protocol (BEEP)).  The following strategy SHOULD be used:

   1.  If a request requires authentication, confidentiality, or other
       security, use another transfer protocol.  IRIS-XPC [9] is
       RECOMMENDED.

   2.  The maximum packet size should be calculated as follows:

       a.  If the path MTU is unknown, the maximum packet size MUST be
           1500 octets.

       b.  If the path MTU is known, the maximum packet size MUST NOT
           exceed the path MTU and MUST NOT exceed 4000 octets.

   3.  If a request is less than or equal to the maximum packet size,
       send it uncompressed.

   4.  If a request can be compressed to a size less than or equal to
       the maximum packet size, send the request using compression.
       Otherwise, use another transfer protocol.  In cases where another
       transfer protocol is needed, IRIS-XPC [9] is RECOMMENDED.

   5.  If a request yields a size error, send the request with another
       transfer protocol.  IRIS-XPC [9] is RECOMMENDED.

   For retransmission of requests considered to be unanswered, a client
   SHOULD retransmit using a timeout value initially set to 1 second.
   This timeout value SHOULD be doubled for every retransmission, and a
   client SHOULD NOT retransmit any request once the timeout value has
   reached 60 seconds.




Newton                      Standards Track                     [Page 9]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


   Clients that use timeout values other than the recommendations above
   MUST allocate or have allocated dedicated network resources that will
   ensure fairness to other network packets and avoid network
   congestion.

   Clients MUST NOT have more than one outstanding request (i.e., an
   unanswered request that has not timed out) at a time unless they
   allocate or have been allocated dedicated network bandwidth and
   resources reserved specifically for this purpose.

   Finally, if a client intends multiple requests to the same server in
   a short amount of time, this protocol offers no real advantage over
   IRIS-XPC [9].  In such a case, IRIS-XPC is RECOMMENDED to be used as
   it would be similarly or more efficient and would offer greater
   response sizes and allow better security.

5.  Internationalization Considerations

   XML processors are obliged to recognize both UTF-8 and UTF-16 [2]
   encodings.  Use of the XML defined by [8] MUST NOT use any other
   character encodings other than UTF-8 or UTF-16.

6.  IRIS Transport Mapping Definitions

   This section lists the definitions required by IRIS [3] for transport
   mappings.

6.1.  URI Scheme

   See Section 7.1.1.

6.2.  Application Protocol Label

   See Section 7.1.3.

7.  IANA Considerations

7.1.  Registrations

7.1.1.  URI Scheme Registration

   URL scheme name: iris.lwz

   Status: permanent

   URL scheme syntax: defined in [3].

   Character encoding considerations: as defined in RFC 3986 [5].



Newton                      Standards Track                    [Page 10]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


   Intended usage: identifies an IRIS entity made available using XML
   over UDP

   Applications using this scheme: defined in IRIS [3].

   Interoperability considerations: n/a

   Security Considerations: defined in Section 8.

   Relevant Publications: IRIS [3].

   Contact Information: Andrew Newton <andy@hxr.us>

   Author/Change controller: the IESG

7.1.2.  Well-known UDP Port Registration

   Protocol Number: UDP

   UDP Port Number: 715

   Message Formats, Types, Opcodes, and Sequences: defined in Sections 3
   and 3.1.

   Functions: defined in IRIS [3].

   Use of Broadcast/Multicast: none

   Proposed Name: IRIS-LWZ

   Short name: iris.lwz

   Contact Information: Andrew Newton <andy@hxr.us>

7.1.3.  S-NAPTR Registration

   Application Protocol Label (see [4]): iris.lwz

   Intended usage: identifies an IRIS server using XML over UDP

   Interoperability considerations: n/a

   Security Considerations: defined in Section 8.

   Relevant Publications: IRIS [3].

   Contact Information: Andrew Newton <andy@hxr.us>




Newton                      Standards Track                    [Page 11]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


   Author/Change controller: the IESG

8.  Security Considerations

   IRIS-LWZ is intended for serving public data; it provides no in-band
   mechanisms for authentication or confidentiality.  Any application
   with these needs must provide out-of-band mechanisms (e.g., IPsec),
   or use the IRIS transfer protocols that provide such capabilities,
   such as IRIS-XPC [9].

   Due to this lack of security, it is possible for an attacker to alter
   IRIS-LWZ messages sent from the client to the server and from the
   server to the client.  Such an attack can result in denying usage of
   an IRIS service or in supplying false information to end users and
   many other scenarios.

   Because IRIS-LWZ is a UDP-based protocol, it is possible for servers
   using IRIS-LWZ to be used in a type of distributed denial-of-service
   attack known as a reflection attack.  This type of attack affects
   other types of UDP-using protocols, such as DNS.  Server operators
   should be prepared to apply the same methods used for mitigating
   reflection attacks with other protocols, such as DNS, when using
   IRIS-LWZ.  All operators should follow the advice given in BCP 38
   [7].

   IRIS-LWZ uses transaction IDs in the payload descriptors to better
   enable a client to match a response to a request.  By randomizing the
   transaction IDs being used (i.e., not using sequential numbers),
   attackers flooding the network with a large amount of spoofed packets
   have a lesser chance of succeeding with the attack.  This measure is
   not guaranteed to thwart any such attack.  Client implementers MUST
   take appropriate measures when ignoring this advice.



















Newton                      Standards Track                    [Page 12]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


9.  References

9.1.  Normative References

   [1]   Deutsch, P., "DEFLATE Compressed Data Format Specification
         version 1.3", RFC 1951, May 1996.

   [2]   The Unicode Consortium, "The Unicode Standard, Version 3", ISBN
         0-201-61633-5, 2000, <The Unicode Standard, Version 3>.

   [3]   Newton, A. and M. Sanz, "IRIS: The Internet Registry
         Information Service (IRIS) Core Protocol", RFC 3981, January
         2005.

   [4]   Daigle, L. and A. Newton, "Domain-Based Application Service
         Location Using SRV RRs and the Dynamic Delegation Discovery
         Service (DDDS)", RFC 3958, January 2005.

   [5]  Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
         Resource Identifier (URI): Generic Syntax", STD 66, RFC 3986,
         January 2005.

   [6]   Bradner, S., "Key words for use in RFCs to Indicate Requirement
         Levels", RFC 2119, BCP 14, March 1997.

   [7]   Ferguson, P. and D. Senie, "Network Ingress Filtering:
         Defeating Denial of Service Attacks which employ IP Source
         Address Spoofing", BCP 38, RFC 2827, May 2000.

   [8]   Newton, A., "A Common Schema for Internet Registry Information
         Service Transfer Protocols", RFC 4991, August 2007.

   [9]   Newton, A., "XML Pipelining with Chunks for the Internet
         Registry Information Service", RFC 4992, August 2007.

9.2.  Informative References

   [10]  Kirkpatrick, S., Stahl, M., and M. Recker, "Internet numbers",
         RFC 1166, July 1990.












Newton                      Standards Track                    [Page 13]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


Appendix A.  Examples

   This section gives examples of IRIS-LWZ exchanges.  Lines beginning
   with "C:" denote data sent by the client to the server, and lines
   beginning with "S:" denote data sent by the server to the client.
   Following the "C:" or "S:", the line contains either octet values in
   hexadecimal notation with comments or XML fragments.  No line
   contains both octet values with comments and XML fragments.  Comments
   are contained within parentheses.










































Newton                      Standards Track                    [Page 14]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


   The following example demonstrates an IRIS client requesting a lookup
   of 'AUP' in the 'local' entity class of a 'dreg1' registry.  The
   client passes a bag (see [3]) with the search request.  The server
   responds with a 'nameNotFound' response and an explanation.

   C:           (request packet)
   C: 0x08      (header: V=0,RR=request,PD=no,DS=yes,PT=xml)
   C: 0x03 0xA4 (transaction ID=932)
   C: 0x05 0xDA (maximum response size=1498)
   C: 0x09      (authority length=9)
   C:           (authority="localhost")
   C: 0x6c 0x6f 0x63 0x61 0x6c 0x68 0x6f 0x73 0x74
   C:           (IRIS XML request)
   C: <request xmlns="urn:ietf:params:xml:ns:iris1"
   C:    xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" >
   C:    <searchSet>
   C:      <bag>
   C:        <simpleBag xmlns="http://example.com/">
   C:          <salt>127.0.0.1:3434</salt>
   C:          <md5>4LnQ1KdCahzyvwBqJis5rw==</md5>
   C:        </simpleBag>
   C:      </bag>
   C:      <lookupEntity
   C:        registryType="dreg1"
   C:        entityClass="local"
   C:        entityName="AUP" />
   C:    </searchSet>
   C: </request>

   S:           (response packet)
   S: 0x20      (header: V=0,RR=response,PD=no,DS=no,PT=xml)
   S: 0x03 0xA4 (transaction ID=932)
   S:           (IRIS XML response)
   S: <iris:response xmlns:iris="urn:ietf:params:xml:ns:iris1">
   S: <iris:resultSet><iris:answer></iris:answer>
   S: <iris:nameNotFound><iris:explanation language="en-US">
   S: The name 'AUP' is not found in 'local'.</iris:explanation>
   S: </iris:nameNotFound></iris:resultSet></iris:response>

                                 Example 1











Newton                      Standards Track                    [Page 15]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


   The following example demonstrates an IRIS client requesting domain
   availability information for 'milo.example.com'.  The server responds
   that the domain is assigned and active.

   C:           (request packet)
   C: 0x00      (header: V=0,RR=request,PD=no,DS=no,PT=xml)
   C: 0x0B 0xE7 (transaction ID=3047)
   C: 0x0F 0xA0 (maximum response size=4000)
   C: 0x0B      (authority length=11)
   C:           (authority="example.com")
   C: 0x65 0x78 0x61 0x6D 0x70 0x6C 0x65 0x23 0x63 0x6F 0x6D
   C:           (IRIS XML request)
   C: <request xmlns="urn:ietf:params:xml:ns:iris1"
   C:   xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
   C:   xsi:schemaLocation="urn:ietf:params:xml:ns:iris1 iris.xsd" >
   C:   <searchSet>
   C:     <lookupEntity
   C:       registryType="urn:ietf:params:xml:ns:dchk1"
   C:       entityClass="domain-name"
   C:       entityName="milo.example.com" />
   C:   </searchSet>
   C: </request>

   S:           (response packet)
   S: 0x20      (header: V=0,RR=response,PD=no,DS=no,PT=xml)
   S: 0x0B 0xE7 (transaction ID=3047)
   S:           (IRIS XML response)
   S: <iris:response xmlns:iris="urn:ietf:params:xml:ns:iris1">
   S: <iris:resultSet><iris:answer><domain
   S: authority="example.com" registryType="dchk1"
   S: entityClass="domain-name" entityName="tcs-com-1"
   S: temporaryReference="true"
   S: xmlns="urn:ietf:params:xml:ns:dchk1"><domainName>
   S: milo.example.com</domainName><status><assignedAndActive/>
   S: </status></domain></iris:answer>
   S: </iris:resultSet></iris:response>

                                 Example 2













Newton                      Standards Track                    [Page 16]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


   The following example demonstrates an IRIS client requesting domain
   availability information for felix.example.net, hobbes.example.net,
   and daffy.example.net.  The client does not support responses
   compressed with DEFLATE, and the maximum UDP packet it can safely
   receive is 498 octets.  The server responds with size information
   indicating that it would take 1211 octets to provide an answer.

   C:           (request packet)
   C: 0x00      (header: V=0,RR=request,PD=no,DS=no,PT=xml)
   C: 0x7E 0x8A (transaction ID=32394)
   C: 0x01 0xF2 (maximum response size=498)
   C: 0x0B      (authority length=11)
   C:           (authority="example.net")
   C: 0x65 0x78 0x61 0x6D 0x70 0x6C 0x65 0x23 0x6E 0x65 0x74
   C:           (IRIS XML request)
   C: <request xmlns="urn:ietf:params:xml:ns:iris1"
   C:   xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
   C:   xsi:schemaLocation="urn:ietf:params:xml:ns:iris1 iris1.xsd">
   C:   <searchSet>
   C:     <lookupEntity registryType="dchk1" entityClass="domain-name"
   C:       entityName="felix.example.net" />
   C:   </searchSet>
   C:   <searchSet>
   C:     <lookupEntity registryType="dchk1" entityClass="domain-name"
   C:       entityName="hobbes.example.net" />
   C:   </searchSet>
   C:   <searchSet>
   C:     <lookupEntity registryType="dchk1" entityClass="domain-name"
   C:       entityName="daffy.example.net" />
   C:   </searchSet>
   C: </request>

   S:           (response packet)
   S: 0x22      (header: V=0,RR=response,PD=no,DS=no,PT=si)
   S: 0x7E 0x8A (transaction ID=32394)
   S:           (Size Information XML response)
   S: <responseSize xmlns="urn:ietf:params:xml:ns:iris-transport">
   S:   <octets>1211</octets>
   S: </responseSize>

                                 Example 3










Newton                      Standards Track                    [Page 17]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


   The following example illustrates an IRIS client requesting the
   version information from a server, and the server returning the
   version information.

   C:           (request packet)
   C: 0x01      (header: V=0,RR=request,PD=no,DS=no,PT=vi)
   C: 0x2E 0x9C (transaction ID=11932)
   C: 0x01 0xF2 (maximum response size=498)
   C: 0x0B      (authority length=11)
   C:           (authority="example.net")
   C: 0x65 0x78 0x61 0x6D 0x70 0x6C 0x65 0x23 0x6E 0x65 0x74

   S:           (response packet)
   S: 0x21      (header: V=0,RR=response,PD=no,DS=no,PT=vi)
   S: 0x2E 0x9C (transaction ID=11932)
   S:           (Version Information XML response)
   S: <versions xmlns="urn:ietf:params:xml:ns:iris-transport">
   S:   <transferProtocol protocolId="iris.lwz1">
   S:     <application protocolId="urn:ietf:params:xml:ns:iris1">
   S:       <dataModel protocolId="urn:ietf:params:xml:ns:dchk1"/>
   S:       <dataModel protocolId="urn:ietf:params:xml:ns:dreg1"/>
   S:     </application>
   S:   </transferProtocol>
   S: </versions>

                                 Example 4

Appendix B.  Contributors

   Substantive contributions to this document have been provided by the
   members of the IETF's CRISP Working Group, especially Milena Caires
   and David Blacka.

Author's Address

   Andrew L. Newton
   VeriSign, Inc.
   21345 Ridgetop Circle
   Sterling, VA  20166
   USA

   Phone: +1 703 948 3382
   EMail: andy@hxr.us
   URI:   http://www.verisignlabs.com/







Newton                      Standards Track                    [Page 18]


RFC 4993      Lightweight UDP Transfer Protocol for IRIS     August 2007


Full Copyright Statement

   Copyright (C) The IETF Trust (2007).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.







Newton                      Standards Track                    [Page 19]