Network Working Group A. Siddiqui Request for Comments: 4711 D. Romascanu Category: Standards Track Avaya E. Golovinsky Alert Logic October 2006 Real-time Application Quality-of-Service Monitoring (RAQMON) MIB Status of This Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Copyright Notice Copyright (C) The Internet Society (2006). Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. The document proposes an extension to the Remote Monitoring MIB, RFC 2819. In particular, it describes managed objects used for real-time application Quality of Service (QoS) monitoring. Table of Contents 1. Introduction ....................................................2 2. The Internet-Standard Management Framework ......................2 3. RAQMON Framework ................................................2 4. Structure of the RAQMON MIB .....................................2 5. RAQMON MIB Definitions ..........................................3 6. Security Considerations ........................................33 7. IANA Considerations ............................................35 8. Acknowledgements ...............................................35 9. Normative References ...........................................36 10. Informative References ........................................36 Siddiqui, et al. Standards Track [Page 1] RFC 4711 RAQMON MIB October 2006 1. Introduction This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it extends [RFC2819] with managed objects used for real-time application QoS monitoring. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 2. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 3. RAQMON Framework As outlined in [RFC4710], the RAQMON framework is based on three entities: - RAQMON Data Source (RDS) - RAQMON Report Collector (RRC) - RAQMON MIB Structure The RAQMON MIB describes information passed between RRCs and a RAQMON Application ("RAQMON manager"). 4. Structure of the RAQMON MIB The RAQMON MIB module is composed of three MIB groups: raqmonSession, raqmonException, and raqmonConfig. The raqmonSession MIB group incorporates the following tables: Siddiqui, et al. Standards Track [Page 2] RFC 4711 RAQMON MIB October 2006 - The raqmonParticpantTable contains information about participants in open and closed (terminated) sessions, including parameters of the sessions they are involved in, aggregated since the beginning of the session. - The raqmonQosTable contains historical information about QoS during sessions. The set of parameters represented in this table is more restricted, but it includes historical per- RAQMON-report information. - The raqmonParticpantAddrTable maps participant addresses into the indices of the raqmonParticpantTable. This table allows management applications to find entries sorted by raqmonParticipantAddr rather than raqmonParticipantStartDate. The raqmonException MIB group includes a table of filters that trigger notifications for sessions with poor QoS. The raqmonConfig MIB group includes objects that define the configuration of the RAQMON Report Collector. This MIB module MUST be implemented by RAQMON Report Collectors. A separate MIB module is defined in [RFC4712] for mapping the RAQMON PDUs onto an SNMP transport. The MIB module defined in [RFC4712] is normally implemented by RAQMON Data Sources (RDS). 5. RAQMON MIB Definitions The MIB module herein IMPORTS definitions from the following: SNMPv2-SMI [RFC2578] SNMPv2-TC [RFC2579] SNMPv2-CONF [RFC2580] RMON-MIB [RFC2819] SNMP-FRAMEWORK-MIB [RFC3411] INET-ADDRESS-MIB [RFC4001] It also uses REFERENCE clauses to refer to [RFC4710]. It also mentions [RFC3737] with respect to the MODULE-IDENTITY OID allocation. Siddiqui, et al. Standards Track [Page 3] RFC 4711 RAQMON MIB October 2006 RAQMON-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-GROUP, NOTIFICATION-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF Integer32, Unsigned32, Gauge32, Counter32, OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE FROM SNMPv2-SMI InetAddressType, InetAddress, InetPortNumber FROM INET-ADDRESS-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB rmon FROM RMON-MIB RowStatus, TruthValue, DateAndTime, RowPointer FROM SNMPv2-TC; raqmonMIB MODULE-IDENTITY LAST-UPDATED "200610100000Z" -- October 10, 2006 ORGANIZATION "IETF RMON MIB Working Group" CONTACT-INFO "WG Charter: http://www.ietf.org/html.charters/rmonmib-charter.html Mailing lists: General Discussion: rmonmib@ietf.org To Subscribe: rmonmib-requests@ietf.org In Body: subscribe your_email_address Chair: Andy Bierman Email: ietf@andybierman.com Editor: Dan Romascanu Avaya Email: dromasca@avaya.com" DESCRIPTION "Real-Time Application QoS Monitoring MIB. Copyright (c) The Internet Society (2006). This version of this MIB module is part of RFC 4711; See the RFC itself for full legal notices." REVISION "200610100000Z" DESCRIPTION "Initial version, published as RFC 4711." ::= { rmon 31 } -- This OID allocation conforms to [RFC3737] Siddiqui, et al. Standards Track [Page 4] RFC 4711 RAQMON MIB October 2006 -- -- Node definitions -- raqmonNotifications OBJECT IDENTIFIER ::= { raqmonMIB 0 } raqmonSessionAlarm NOTIFICATION-TYPE OBJECTS { raqmonParticipantAddr, raqmonParticipantName, raqmonParticipantPeerAddrType, raqmonParticipantPeerAddr, raqmonQoSEnd2EndNetDelay, raqmonQoSInterArrivalJitter, raqmonQosLostPackets, raqmonQosRcvdPackets } STATUS current DESCRIPTION "A notification generated by an entry in the raqmonSessionExceptionTable." ::= { raqmonNotifications 1 } raqmonMIBObjects OBJECT IDENTIFIER ::= { raqmonMIB 1 } raqmonSession OBJECT IDENTIFIER ::= { raqmonMIBObjects 1 } raqmonParticipantTable OBJECT-TYPE SYNTAX SEQUENCE OF RaqmonParticipantEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about participants in both active and closed (terminated) sessions." ::= { raqmonSession 1 } raqmonParticipantEntry OBJECT-TYPE SYNTAX RaqmonParticipantEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains information for a single session (application) run by one participant. Indexation by the start time of the session aims to ease sorting by management applications. Agents MUST NOT report identical start times for any two sessions on the same host. Rows are removed for inactive sessions when implementation-specific age or space limits are reached." Siddiqui, et al. Standards Track [Page 5] RFC 4711 RAQMON MIB October 2006 INDEX { raqmonParticipantStartDate, raqmonParticipantIndex } ::= { raqmonParticipantTable 1 } RaqmonParticipantEntry ::= SEQUENCE { raqmonParticipantStartDate DateAndTime, raqmonParticipantIndex Unsigned32, raqmonParticipantReportCaps BITS, raqmonParticipantAddrType InetAddressType, raqmonParticipantAddr InetAddress, raqmonParticipantSendPort InetPortNumber, raqmonParticipantRecvPort InetPortNumber, raqmonParticipantSetupDelay Integer32, raqmonParticipantName SnmpAdminString, raqmonParticipantAppName SnmpAdminString, raqmonParticipantQosCount Gauge32, raqmonParticipantEndDate DateAndTime, raqmonParticipantDestPayloadType Integer32, raqmonParticipantSrcPayloadType Integer32, raqmonParticipantActive TruthValue, raqmonParticipantPeer RowPointer, raqmonParticipantPeerAddrType InetAddressType, raqmonParticipantPeerAddr InetAddress, raqmonParticipantSrcL2Priority Integer32, raqmonParticipantDestL2Priority Integer32, raqmonParticipantSrcDSCP Integer32, raqmonParticipantDestDSCP Integer32, raqmonParticipantCpuMean Integer32, raqmonParticipantCpuMin Integer32, raqmonParticipantCpuMax Integer32, raqmonParticipantMemoryMean Integer32, raqmonParticipantMemoryMin Integer32, raqmonParticipantMemoryMax Integer32, raqmonParticipantNetRTTMean Integer32, raqmonParticipantNetRTTMin Integer32, raqmonParticipantNetRTTMax Integer32, raqmonParticipantIAJitterMean Integer32, raqmonParticipantIAJitterMin Integer32, raqmonParticipantIAJitterMax Integer32, raqmonParticipantIPDVMean Integer32, raqmonParticipantIPDVMin Integer32, raqmonParticipantIPDVMax Integer32, raqmonParticipantNetOwdMean Integer32, raqmonParticipantNetOwdMin Integer32, raqmonParticipantNetOwdMax Integer32, raqmonParticipantAppDelayMean Integer32, raqmonParticipantAppDelayMin Integer32, raqmonParticipantAppDelayMax Integer32, Siddiqui, et al. Standards Track [Page 6] RFC 4711 RAQMON MIB October 2006 raqmonParticipantPacketsRcvd Integer32, raqmonParticipantPacketsSent Integer32, raqmonParticipantOctetsRcvd Integer32, raqmonParticipantOctetsSent Integer32, raqmonParticipantLostPackets Integer32, raqmonParticipantLostPacketsFrct Integer32, raqmonParticipantDiscards Integer32, raqmonParticipantDiscardsFrct Integer32 } raqmonParticipantStartDate OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS not-accessible STATUS current DESCRIPTION "The date and time of this entry. It will be the date and time of the first report received." ::= { raqmonParticipantEntry 1 } raqmonParticipantIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the conceptual row, which is for SNMP purposes only and has no relation to any protocol value. There is no requirement that these rows be created or maintained sequentially. The index will be unique for a particular date and time." ::= { raqmonParticipantEntry 2 } raqmonParticipantReportCaps OBJECT-TYPE SYNTAX BITS { raqmonPartRepDsrcName(0), raqmonPartRepRecvName(1), raqmonPartRepDsrcPort(2), raqmonPartRepRecvPort(3), raqmonPartRepSetupTime(4), raqmonPartRepSetupDelay(5), raqmonPartRepSessionDuration(6), raqmonPartRepSetupStatus(7), raqmonPartRepRTEnd2EndNetDelay(8), raqmonPartRepOWEnd2EndNetDelay(9), raqmonPartApplicationDelay(10), raqmonPartRepIAJitter(11), raqmonPartRepIPDV(12), Siddiqui, et al. Standards Track [Page 7] RFC 4711 RAQMON MIB October 2006 raqmonPartRepRcvdPackets(13), raqmonPartRepRcvdOctets(14), raqmonPartRepSentPackets(15), raqmonPartRepSentOctets(16), raqmonPartRepCumPacketsLoss(17), raqmonPartRepFractionPacketsLoss(18), raqmonPartRepCumDiscards(19), raqmonPartRepFractionDiscards(20), raqmonPartRepSrcPayloadType(21), raqmonPartRepDestPayloadType(22), raqmonPartRepSrcLayer2Priority(23), raqmonPartRepSrcTosDscp(24), raqmonPartRepDestLayer2Priority(25), raqmonPartRepDestTosDscp(26), raqmonPartRepCPU(27), raqmonPartRepMemory(28), raqmonPartRepAppName(29) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Report capabilities of the participant, as perceived by the Collector. If the participant can report the Data Source Name as defined in [RFC4710], Section 5.3, then the raqmonPartRepDsrcName bit will be set. If the participant can report the Receiver Name as defined in [RFC4710], Section 5.4, then the raqmonPartRepRecvName bit will be set. If the participant can report the Data Source Port as defined in [RFC4710], Section 5.5, then the raqmonPartRepDsrcPort bit will be set. If the participant can report the Receiver Port as defined in [RFC4710], Section 5.6, then the raqmonPartRepRecvPort bit will be set. If the participant can report the Session Setup Time as defined in [RFC4710], Section 5.7, then the raqmonPartRepSetupTime bit will be set. If the participant can report the Session Setup Delay as defined in [RFC4710], Section 5.8, then the raqmonPartRepSetupDelay bit will be set. Siddiqui, et al. Standards Track [Page 8] RFC 4711 RAQMON MIB October 2006 If the participant can report the Session Duration as defined in [RFC4710], Section 5.9, then the raqmonPartRepSessionDuration bit will be set. If the participant can report the Setup Status as defined in [RFC4710], Section 5.10, then the raqmonPartRepSetupStatus bit will be set. If the participant can report the Round-Trip End-to-end Network Delay as defined in [RFC4710], Section 5.11, then the raqmonPartRepRTEnd2EndNetDelay bit will be set. If the participant can report the One-way End-to-end Network Delay as defined in [RFC4710], Section 5.12, then the raqmonPartRepOWEnd2EndNetDelay bit will be set. If the participant can report the Application Delay as defined in [RFC4710], Section 5.13, then the raqmonPartApplicationDelay bit will be set. If the participant can report the Inter-Arrival Jitter as defined in [RFC4710], Section 5.14, then the raqmonPartRepIAJitter bit will be set. If the participant can report the IP Packet Delay Variation as defined in [RFC4710], Section 5.15, then the raqmonPartRepIPDV bit will be set. If the participant can report the number of application packets received as defined in [RFC4710], Section 5.16, then the raqmonPartRepRcvdPackets bit will be set. If the participant can report the number of application octets received as defined in [RFC4710], Section 5.17, then the raqmonPartRepRcvdOctets bit will be set. If the participant can report the number of application packets sent as defined in [RFC4710], Section 5.18, then the raqmonPartRepSentPackets bit will be set. If the participant can report the number of application octets sent as defined in [RFC4710], Section 5.19, then the raqmonPartRepSentOctets bit will be set. If the participant can report the number of cumulative packets lost as defined in [RFC4710], Section 5.20, then the raqmonPartRepCumPacketsLoss bit will be set. Siddiqui, et al. Standards Track [Page 9] RFC 4711 RAQMON MIB October 2006 If the participant can report the fraction of packet loss as defined in [RFC4710], Section 5.21, then the raqmonPartRepFractionPacketsLoss bit will be set. If the participant can report the number of cumulative discards as defined in [RFC4710], Section 5.22, then the raqmonPartRepCumDiscards bit will be set. If the participant can report the fraction of discards as defined in [RFC4710], Section 5.23, then the raqmonPartRepFractionDiscards bit will be set. If the participant can report the Source Payload Type as defined in [RFC4710], Section 5.24, then the raqmonPartRepSrcPayloadType bit will be set. If the participant can report the Destination Payload Type as defined in [RFC4710], Section 5.25, then the raqmonPartRepDestPayloadType bit will be set. If the participant can report the Source Layer 2 Priority as defined in [RFC4710], Section 5.26, then the raqmonPartRepSrcLayer2Priority bit will be set. If the participant can report the Source DSCP/ToS value as defined in [RFC4710], Section 5.27, then the raqmonPartRepSrcToSDscp bit will be set. If the participant can report the Destination Layer 2 Priority as defined in [RFC4710], Section 5.28, then the raqmonPartRepDestLayer2Priority bit will be set. If the participant can report the Destination DSCP/ToS Value as defined in [RFC4710], Section 5.29, then the raqmonPartRepDestToSDscp bit will be set. If the participant can report the CPU utilization as defined in [RFC4710], Section 5.30, then the raqmonPartRepCPU bit will be set. If the participant can report the memory utilization as defined in [RFC4710], Section 5.31, then the raqmonPartRepMemory bit will be set. If the participant can report the Application Name as defined in [RFC4710], Section 5.32, then the raqmonPartRepAppName bit will be set. Siddiqui, et al. Standards Track [Page 10] RFC 4711 RAQMON MIB October 2006 The capability of reporting of a specific metric does not mandate that the metric must be reported permanently by the data source to the respective collector. Some data sources MAY be configured not to send a metric, or some metrics may not be relevant to the specific application." ::= { raqmonParticipantEntry 3 } raqmonParticipantAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the Internet address of the participant for this session." ::= { raqmonParticipantEntry 4 } raqmonParticipantAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Internet Address of the participant for this session. Formatting of this object is determined by the value of raqmonParticipantAddrType." ::= { raqmonParticipantEntry 5 } raqmonParticipantSendPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Port from which session data is sent. If the value was not reported to the collector, this object will have the value 0." REFERENCE "Section 5.5 of the [RFC4710]" ::= { raqmonParticipantEntry 6 } raqmonParticipantRecvPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Port on which session data is received. If the value was not reported to the collector, this object will have the value 0." REFERENCE Siddiqui, et al. Standards Track [Page 11] RFC 4711 RAQMON MIB October 2006 "Section 5.6 of the [RFC4710]" ::= { raqmonParticipantEntry 7 } raqmonParticipantSetupDelay OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Session setup time. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.8 of the [RFC4710]" ::= { raqmonParticipantEntry 8 } raqmonParticipantName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The data source name for the participant." REFERENCE "Section 5.3 of the [RFC4710]" ::= { raqmonParticipantEntry 9 } raqmonParticipantAppName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A string giving the name and possibly the version of the application generating the stream, e.g., 'videotool 1.2.' This information may be useful for debugging purposes and is similar to the Mailer or Mail-System-Version SMTP headers. The tool value is expected to remain constant for the duration of the session." REFERENCE "Section 5.32 of the [RFC4710]" ::= { raqmonParticipantEntry 10 } raqmonParticipantQosCount OBJECT-TYPE SYNTAX Gauge32 UNITS "entries" MAX-ACCESS read-only STATUS current Siddiqui, et al. Standards Track [Page 12] RFC 4711 RAQMON MIB October 2006 DESCRIPTION "The current number of entries in the raqmonQosTable for this participant and session." ::= { raqmonParticipantEntry 11 } raqmonParticipantEndDate OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time of the most recent report received." ::= { raqmonParticipantEntry 12 } raqmonParticipantDestPayloadType OBJECT-TYPE SYNTAX Integer32 (-1|0..127) MAX-ACCESS read-only STATUS current DESCRIPTION "Destination Payload Type. If the value was not reported to the collector, this object will have the value -1." REFERENCE "RFC 3551 and Section 5.25 of the [RFC4710]" ::= { raqmonParticipantEntry 13 } raqmonParticipantSrcPayloadType OBJECT-TYPE SYNTAX Integer32 (-1|0..127) MAX-ACCESS read-only STATUS current DESCRIPTION "Source Payload Type. If the value was not reported to the collector, this object will have the value -1." REFERENCE "RFC 3551 and Section 5.24 of the [RFC4710]" ::= { raqmonParticipantEntry 14 } raqmonParticipantActive OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Value 'true' indicates that the session for this participant is active (open). Value 'false' indicates that the session is closed (terminated)." ::= { raqmonParticipantEntry 15 } Siddiqui, et al. Standards Track [Page 13] RFC 4711 RAQMON MIB October 2006 raqmonParticipantPeer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "The pointer to the corresponding entry in this table for the other peer participant. If there is no such entry in the participant table of the collector represented by this SNMP agent, then the value will be { 0 0 }. " ::= { raqmonParticipantEntry 16 } raqmonParticipantPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the Internet address of the peer participant for this session." ::= { raqmonParticipantEntry 17 } raqmonParticipantPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Internet Address of the peer participant for this session. Formatting of this object is determined by the value of raqmonParticipantPeerAddrType." ::= { raqmonParticipantEntry 18 } raqmonParticipantSrcL2Priority OBJECT-TYPE SYNTAX Integer32 (-1|0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Source Layer 2 Priority. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.26 of the [RFC4710]" ::= { raqmonParticipantEntry 19 } raqmonParticipantDestL2Priority OBJECT-TYPE SYNTAX Integer32 (-1|0..7) MAX-ACCESS read-only STATUS current DESCRIPTION Siddiqui, et al. Standards Track [Page 14] RFC 4711 RAQMON MIB October 2006 "Destination Layer 2 Priority. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.28 of the [RFC4710]" ::= { raqmonParticipantEntry 20 } raqmonParticipantSrcDSCP OBJECT-TYPE SYNTAX Integer32 (-1|0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Source Layer 3 DSCP value. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.27 of the [RFC4710]" ::= { raqmonParticipantEntry 21 } raqmonParticipantDestDSCP OBJECT-TYPE SYNTAX Integer32 (-1|0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Destination Layer 3 DSCP value." REFERENCE "Section 5.29 of the [RFC4710]" ::= { raqmonParticipantEntry 22 } raqmonParticipantCpuMean OBJECT-TYPE SYNTAX Integer32 (-1|0..100) UNITS "percents" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean CPU utilization. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.30 of the [RFC4710]" ::= { raqmonParticipantEntry 23 } raqmonParticipantCpuMin OBJECT-TYPE SYNTAX Integer32 (-1|0..100) UNITS "percents" MAX-ACCESS read-only STATUS current DESCRIPTION Siddiqui, et al. Standards Track [Page 15] RFC 4711 RAQMON MIB October 2006 "Minimum CPU utilization. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.30 of the [RFC4710]" ::= { raqmonParticipantEntry 24 } raqmonParticipantCpuMax OBJECT-TYPE SYNTAX Integer32 (-1|0..100) UNITS "percents" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum CPU utilization. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.30 of the [RFC4710]" ::= { raqmonParticipantEntry 25 } raqmonParticipantMemoryMean OBJECT-TYPE SYNTAX Integer32 (-1|0..100) UNITS "percents" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean memory utilization. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.31 of the [RFC4710]" ::= { raqmonParticipantEntry 26 } raqmonParticipantMemoryMin OBJECT-TYPE SYNTAX Integer32 (-1|0..100) UNITS "percents" MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum memory utilization. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.31 of the [RFC4710]" ::= { raqmonParticipantEntry 27 } raqmonParticipantMemoryMax OBJECT-TYPE SYNTAX Integer32 (-1|0..100) Siddiqui, et al. Standards Track [Page 16] RFC 4711 RAQMON MIB October 2006 UNITS "percents" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum memory utilization. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.31 of the [RFC4710]" ::= { raqmonParticipantEntry 28 } raqmonParticipantNetRTTMean OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean round-trip end-to-end network delay over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.11 of the [RFC4710]" ::= { raqmonParticipantEntry 29 } raqmonParticipantNetRTTMin OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum round-trip end-to-end network delay over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.11 of the [RFC4710]" ::= { raqmonParticipantEntry 30 } raqmonParticipantNetRTTMax OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum round-trip end-to-end network delay over the entire session. If the value was not reported to the collector, Siddiqui, et al. Standards Track [Page 17] RFC 4711 RAQMON MIB October 2006 this object will have the value -1." REFERENCE "Section 5.11 of the [RFC4710]" ::= { raqmonParticipantEntry 31 } raqmonParticipantIAJitterMean OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean inter-arrival jitter over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.14 of the [RFC4710]" ::= { raqmonParticipantEntry 32 } raqmonParticipantIAJitterMin OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum inter-arrival jitter over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.14 of the [RFC4710]" ::= { raqmonParticipantEntry 33 } raqmonParticipantIAJitterMax OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum inter-arrival jitter over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.14 of the [RFC4710]" ::= { raqmonParticipantEntry 34 } raqmonParticipantIPDVMean OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only Siddiqui, et al. Standards Track [Page 18] RFC 4711 RAQMON MIB October 2006 STATUS current DESCRIPTION "Mean IP packet delay variation over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.15 of the [RFC4710]" ::= { raqmonParticipantEntry 35 } raqmonParticipantIPDVMin OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum IP packet delay variation over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.15 of the [RFC4710]" ::= { raqmonParticipantEntry 36 } raqmonParticipantIPDVMax OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum IP packet delay variation over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.15 of the [RFC4710]" ::= { raqmonParticipantEntry 37 } raqmonParticipantNetOwdMean OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean Network one-way delay over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.12 of the [RFC4710]" ::= { raqmonParticipantEntry 38 } Siddiqui, et al. Standards Track [Page 19] RFC 4711 RAQMON MIB October 2006 raqmonParticipantNetOwdMin OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum Network one-way delay over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.12 of the [RFC4710]" ::= { raqmonParticipantEntry 39 } raqmonParticipantNetOwdMax OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum Network one-way delay over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.1 of the [RFC4710]" ::= { raqmonParticipantEntry 40 } raqmonParticipantAppDelayMean OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Mean application delay over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.13 of the [RFC4710]" ::= { raqmonParticipantEntry 41 } raqmonParticipantAppDelayMin OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum application delay over the entire session. If the value was not reported to the collector, this object will have the value -1." Siddiqui, et al. Standards Track [Page 20] RFC 4711 RAQMON MIB October 2006 REFERENCE "Section 5.13 of the [RFC4710]" ::= { raqmonParticipantEntry 42 } raqmonParticipantAppDelayMax OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum application delay over the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.13 of the [RFC4710]" ::= { raqmonParticipantEntry 43 } raqmonParticipantPacketsRcvd OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets received for the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.16 of the [RFC4710]" ::= { raqmonParticipantEntry 44 } raqmonParticipantPacketsSent OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets sent for the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.17 of the [RFC4710]" ::= { raqmonParticipantEntry 45 } raqmonParticipantOctetsRcvd OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "Octets" MAX-ACCESS read-only STATUS current Siddiqui, et al. Standards Track [Page 21] RFC 4711 RAQMON MIB October 2006 DESCRIPTION "Count of octets received for the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.18 of the [RFC4710]" ::= { raqmonParticipantEntry 46 } raqmonParticipantOctetsSent OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of octets sent for the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.19 of the [RFC4710]" ::= { raqmonParticipantEntry 47 } raqmonParticipantLostPackets OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets lost by this receiver for the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.20 of the [RFC4710]" ::= { raqmonParticipantEntry 48 } raqmonParticipantLostPacketsFrct OBJECT-TYPE SYNTAX Integer32 (-1|0..100) UNITS "percents" MAX-ACCESS read-only STATUS current DESCRIPTION "Fraction of lost packets out of total packets received. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.21 of the [RFC4710]" ::= { raqmonParticipantEntry 49 } Siddiqui, et al. Standards Track [Page 22] RFC 4711 RAQMON MIB October 2006 raqmonParticipantDiscards OBJECT-TYPE SYNTAX Integer32 (-1|0..2147483647) UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets discarded by this receiver for the entire session. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.22 of the [RFC4710]" ::= { raqmonParticipantEntry 50 } raqmonParticipantDiscardsFrct OBJECT-TYPE SYNTAX Integer32 (-1|0..100) UNITS "percents" MAX-ACCESS read-only STATUS current DESCRIPTION "Fraction of discarded packets out of total packets received. If the value was not reported to the collector, this object will have the value -1." REFERENCE "Section 5.23 of the [RFC4710]" ::= { raqmonParticipantEntry 51 } raqmonQosTable OBJECT-TYPE SYNTAX SEQUENCE OF RaqmonQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of historical information about quality-of-service data during sessions." ::= { raqmonSession 2 } raqmonQosEntry OBJECT-TYPE SYNTAX RaqmonQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information from a single RAQMON packet, related to a single session (application) run by one participant. Indexation by the start time of the session aims to ease sorting by management applications. Agents MUST NOT report identical start times for any two sessions Siddiqui, et al. Standards Track [Page 23] RFC 4711 RAQMON MIB October 2006 on the same host. Rows are removed for inactive sessions when implementation-specific time or space limits are reached." INDEX { raqmonParticipantStartDate, raqmonParticipantIndex, raqmonQosTime } ::= { raqmonQosTable 1 } RaqmonQosEntry ::= SEQUENCE { raqmonQosTime Unsigned32, raqmonQoSEnd2EndNetDelay Integer32, raqmonQoSInterArrivalJitter Integer32, raqmonQosRcvdPackets Integer32, raqmonQosRcvdOctets Integer32, raqmonQosSentPackets Integer32, raqmonQosSentOctets Integer32, raqmonQosLostPackets Integer32, raqmonQosSessionStatus SnmpAdminString } raqmonQosTime OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) UNITS "seconds" MAX-ACCESS not-accessible STATUS current DESCRIPTION "Time of this entry measured from the start of the corresponding participant session." ::= { raqmonQosEntry 1 } raqmonQoSEnd2EndNetDelay OBJECT-TYPE SYNTAX Integer32 (-1 | 0..2147483647) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The round-trip time. Will contain the previous value if there was no report for this time, or -1 if the value has never been reported." REFERENCE "Section 5.11 of the [RFC4710]" ::= { raqmonQosEntry 2 } raqmonQoSInterArrivalJitter OBJECT-TYPE SYNTAX Integer32 (-1 | 0..2147483647) Siddiqui, et al. Standards Track [Page 24] RFC 4711 RAQMON MIB October 2006 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of delay variation as observed by this receiver. Will contain the previous value if there was no report for this time, or -1 if the value has never been reported." REFERENCE "Section 5.14 of the [RFC4710]" ::= { raqmonQosEntry 3 } raqmonQosRcvdPackets OBJECT-TYPE SYNTAX Integer32 (-1 | 0..2147483647) UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets received by this receiver since the previous entry. Will contain the previous value if there was no report for this time, or -1 if the value has never been reported." REFERENCE "Section 5.16 of the [RFC4710]" ::= { raqmonQosEntry 4 } raqmonQosRcvdOctets OBJECT-TYPE SYNTAX Integer32 (-1 | 0..2147483647) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of octets received by this receiver since the previous report. Will contain the previous value if there was no report for this time, or -1 if the value has never been reported." REFERENCE "Section 5.18 of the [RFC4710]" ::= { raqmonQosEntry 5 } raqmonQosSentPackets OBJECT-TYPE SYNTAX Integer32 (-1 | 0..2147483647) UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of packets sent since the previous report. Will contain the previous value if there Siddiqui, et al. Standards Track [Page 25] RFC 4711 RAQMON MIB October 2006 was no report for this time, or -1 if the value has never been reported." REFERENCE "Section 5.17 of the [RFC4710]" ::= { raqmonQosEntry 6 } raqmonQosSentOctets OBJECT-TYPE SYNTAX Integer32 (-1 | 0..2147483647) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of octets sent since the previous report. Will contain the previous value if there was no report for this time, or -1 if the value has never been reported." REFERENCE "Section 5.19 of the [RFC4710]" ::= { raqmonQosEntry 7 } raqmonQosLostPackets OBJECT-TYPE SYNTAX Integer32 (-1 | 0..2147483647) UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of packets lost as observed by this receiver since the previous report. Will contain the previous value if there was no report for this time, or -1 if the value has never been reported." REFERENCE "Section 5.20 of the [RFC4710]" ::= { raqmonQosEntry 8 } raqmonQosSessionStatus OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The session status. Will contain the previous value if there was no report for this time or the zero-length string if no value was ever reported." REFERENCE "Section 5.10 of the [RFC4710]" ::= { raqmonQosEntry 9 } raqmonParticipantAddrTable OBJECT-TYPE Siddiqui, et al. Standards Track [Page 26] RFC 4711 RAQMON MIB October 2006 SYNTAX SEQUENCE OF RaqmonParticipantAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Maps raqmonParticipantAddr to the index of the raqmonParticipantTable. This table allows management applications to find entries sorted by raqmonParticipantAddr rather than raqmonParticipantStartDate." ::= { raqmonSession 3 } raqmonParticipantAddrEntry OBJECT-TYPE SYNTAX RaqmonParticipantAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry corresponds to exactly one entry in the raqmonParticipantEntry: the entry containing the index pair raqmonParticipantStartDate, raqmonParticipantIndex. Note that there is no concern about the indexation of this table exceeding the limits defined by RFC 2578, Section 3.5. According to [RFC4710], Section 5.1, only IPv4 and IPv6 addresses can be reported as participant addresses." INDEX { raqmonParticipantAddrType, raqmonParticipantAddr, raqmonParticipantStartDate, raqmonParticipantIndex } ::= { raqmonParticipantAddrTable 1 } RaqmonParticipantAddrEntry ::= SEQUENCE { raqmonParticipantAddrEndDate DateAndTime } raqmonParticipantAddrEndDate OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of raqmonParticipantEndDate for the corresponding raqmonParticipantEntry." ::= { raqmonParticipantAddrEntry 1 } raqmonException OBJECT IDENTIFIER ::= { raqmonMIBObjects 2 } raqmonSessionExceptionTable OBJECT-TYPE Siddiqui, et al. Standards Track [Page 27] RFC 4711 RAQMON MIB October 2006 SYNTAX SEQUENCE OF RaqmonSessionExceptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines thresholds for the management station to get notifications about sessions that encountered poor quality of service. The information in this table MUST be persistent across agent reboots." ::= { raqmonException 2 } raqmonSessionExceptionEntry OBJECT-TYPE SYNTAX RaqmonSessionExceptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the raqmonSessionExceptionTable." INDEX { raqmonSessionExceptionIndex } ::= { raqmonSessionExceptionTable 1 } RaqmonSessionExceptionEntry ::= SEQUENCE { raqmonSessionExceptionIndex Unsigned32, raqmonSessionExceptionIAJitterThreshold Unsigned32, raqmonSessionExceptionNetRTTThreshold Unsigned32, raqmonSessionExceptionLostPacketsThreshold Unsigned32, raqmonSessionExceptionRowStatus RowStatus } raqmonSessionExceptionIndex OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the raqmonSessionExceptionTable. Management applications can determine unused indices by performing GetNext or GetBulk operations on the Table." ::= { raqmonSessionExceptionEntry 2 } raqmonSessionExceptionIAJitterThreshold OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION Siddiqui, et al. Standards Track [Page 28] RFC 4711 RAQMON MIB October 2006 "Threshold for jitter. The value during a session must be greater than or equal to this value for an exception to be created." ::= { raqmonSessionExceptionEntry 3 } raqmonSessionExceptionNetRTTThreshold OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Threshold for round-trip time. The value during a session must be greater than or equal to this value for an exception to be created." ::= { raqmonSessionExceptionEntry 4 } raqmonSessionExceptionLostPacketsThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..1000) UNITS "tenth of a percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Threshold for lost packets in units of tenths of a percent. The value during a session must be greater than or equal to this value for an exception to be created." ::= { raqmonSessionExceptionEntry 5 } raqmonSessionExceptionRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object has a value of 'active' when exceptions are being monitored by the system. A newly-created conceptual row must have all the read-create objects initialized before becoming 'active'. A conceptual row that is in the 'notReady' or 'notInService' state MAY be removed after 5 minutes. No writeable objects can be changed while the row is active." ::= { raqmonSessionExceptionEntry 7 } raqmonConfig OBJECT IDENTIFIER ::= { raqmonMIBObjects 3 } raqmonConfigPort OBJECT-TYPE SYNTAX InetPortNumber Siddiqui, et al. Standards Track [Page 29] RFC 4711 RAQMON MIB October 2006 MAX-ACCESS read-write STATUS current DESCRIPTION "The UDP port to listen on for RAQMON reports, running on transport protocols other than SNMP. If the RAQMON PDU transport protocol is SNMP, a write operation on this object has no effect, as the standard port 162 is always used. The value of this object MUST be persistent across agent reboots." ::= { raqmonConfig 1 } raqmonConfigPduTransport OBJECT-TYPE SYNTAX BITS { other(0), tcp(1), snmp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The PDU transport(s) used by this collector. If other(0) is set, the collector supports a transport other than SNMP or TCP. If tcp(1) is set, the collector supports TCP as a transport protocol. If snmp(2) is set, the collector supports SNMP as a transport protocol." ::= { raqmonConfig 2 } raqmonConfigRaqmonPdus OBJECT-TYPE SYNTAX Counter32 UNITS "PDUs" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of RAQMON PDUs received by the Collector." ::= { raqmonConfig 3 } raqmonConfigRDSTimeout OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds since the reception of the last RAQMON PDU from a RDS after which a session Siddiqui, et al. Standards Track [Page 30] RFC 4711 RAQMON MIB October 2006 between the respective RDS and the collector will be considered terminated. The value of this object MUST be persistent across agent reboots." ::= { raqmonConfig 4 } raqmonConformance OBJECT IDENTIFIER ::= { raqmonMIB 2 } raqmonCompliances OBJECT IDENTIFIER ::= { raqmonConformance 1 } raqmonGroups OBJECT IDENTIFIER ::= { raqmonConformance 2 } raqmonCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Describes the requirements for conformance to the RAQMON MIB." MODULE -- this module MANDATORY-GROUPS { raqmonCollectorGroup, raqmonCollectorNotificationsGroup } OBJECT raqmonParticipantAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "Only IPv4 and IPv6 addresses need to be supported." OBJECT raqmonParticipantAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "Only IPv4 and IPv6 addresses need to be supported." OBJECT raqmonParticipantPeerAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "Only IPv4 and IPv6 addresses need to be supported." OBJECT raqmonParticipantPeerAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "Only IPv4 and IPv6 addresses need to be supported." ::= { raqmonCompliances 1 } Siddiqui, et al. Standards Track [Page 31] RFC 4711 RAQMON MIB October 2006 raqmonCollectorGroup OBJECT-GROUP OBJECTS { raqmonParticipantReportCaps, raqmonParticipantAddrType, raqmonParticipantAddr, raqmonParticipantSendPort, raqmonParticipantRecvPort, raqmonParticipantSetupDelay, raqmonParticipantName, raqmonParticipantAppName, raqmonParticipantQosCount, raqmonParticipantEndDate, raqmonParticipantDestPayloadType, raqmonParticipantSrcPayloadType, raqmonParticipantActive, raqmonParticipantPeer, raqmonParticipantPeerAddrType, raqmonParticipantPeerAddr, raqmonParticipantSrcL2Priority, raqmonParticipantDestL2Priority, raqmonParticipantSrcDSCP, raqmonParticipantDestDSCP, raqmonParticipantCpuMean, raqmonParticipantCpuMin, raqmonParticipantCpuMax, raqmonParticipantMemoryMean, raqmonParticipantMemoryMin, raqmonParticipantMemoryMax, raqmonParticipantNetRTTMean, raqmonParticipantNetRTTMin, raqmonParticipantNetRTTMax, raqmonParticipantIAJitterMean, raqmonParticipantIAJitterMin, raqmonParticipantIAJitterMax, raqmonParticipantIPDVMean, raqmonParticipantIPDVMin, raqmonParticipantIPDVMax, raqmonParticipantNetOwdMean, raqmonParticipantNetOwdMin, raqmonParticipantNetOwdMax, raqmonParticipantAppDelayMean, raqmonParticipantAppDelayMin, raqmonParticipantAppDelayMax, raqmonParticipantPacketsRcvd, raqmonParticipantPacketsSent, raqmonParticipantOctetsRcvd, raqmonParticipantOctetsSent, raqmonParticipantLostPackets, Siddiqui, et al. Standards Track [Page 32] RFC 4711 RAQMON MIB October 2006 raqmonParticipantLostPacketsFrct, raqmonParticipantDiscards, raqmonParticipantDiscardsFrct, raqmonQoSEnd2EndNetDelay, raqmonQoSInterArrivalJitter, raqmonQosRcvdPackets, raqmonQosRcvdOctets, raqmonQosSentPackets, raqmonQosSentOctets, raqmonQosLostPackets, raqmonQosSessionStatus, raqmonParticipantAddrEndDate, raqmonConfigPort, raqmonSessionExceptionIAJitterThreshold, raqmonSessionExceptionNetRTTThreshold, raqmonSessionExceptionLostPacketsThreshold, raqmonSessionExceptionRowStatus, raqmonConfigPduTransport, raqmonConfigRaqmonPdus, raqmonConfigRDSTimeout} STATUS current DESCRIPTION "Objects used in RAQMON by a collector." ::= { raqmonGroups 1 } raqmonCollectorNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { raqmonSessionAlarm } STATUS current DESCRIPTION "Notifications emitted by a RAQMON collector." ::= { raqmonGroups 2 } END 6. Security Considerations There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. Setting the value of the object raqmonRDSTimeout to too low a value would result in RDS sessions being terminated sooner than necessary, while setting at too high a value may result in terminated sessions continuing to be managed, with unnecessary memory allocations. Siddiqui, et al. Standards Track [Page 33] RFC 4711 RAQMON MIB October 2006 Setting the following object to incorrect values can result in the collectors either flooding the management applications with unnecessary notifications, or not sending notifications when the QoS in the network may be degraded. raqmonSessionExceptionIAJitterThreshold raqmonSessionExceptionRTTThreshold raqmonSessionExceptionLostPacketsThreshold Setting the raqmonConfigPort object to incorrect values can result in the collector not being able to receive RAQMON PDUs from the data sources. Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. These are: raqmonParticipantTable raqmonQoSTable raqmonParticpantAddrTable Unauthorized exposure of these objects may lead to disclosure of the addresses of the participants in applications, or information about the traffic patents of the applications, which may be considered sensitive in certain environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt their values when sending them over the network via SNMP. The structure of the RAQMON tables limits what can be usefully done for access control configuration using View-based Access Control Model (VACM). For example, with these structures it would not be possible to provide a group, with access to performance data for a specific group of devices, since the index values for raqmonParticpantEntry cannot be known in advance. Likewise, raqmonSessionExceptionEntries apply to all entries in the raqmonQoSTable. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. Siddiqui, et al. Standards Track [Page 34] RFC 4711 RAQMON MIB October 2006 It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 7. IANA Considerations No requirements from IANA are defined in this document. The root OID of the MIB module defined in this document belongs to the RMON subtree, as reserved in [RFC3737]. 8. Acknowledgements Richard Smith created the first proprietary version of this MIB. The authors would also like to thank all the participants in the Remote Monitoring MIB Working Group, and especially Andy Bierman, Steven Waldbusser, Alan Clark, Itai Zilbershtein, and Robert Cole for interesting discussions, ideas, comments, and direct contributions to this work. The authors would also like to thank Randy Presuhn for the precious technical comments, as well as for the laborious activity of reviewing the syntax and spelling of the document. The authors would like to thank Bert Wijnen for the review of the final versions of the document, as well as for the guidance provided during the whole period of editing. Siddiqui, et al. Standards Track [Page 35] RFC 4711 RAQMON MIB October 2006 9. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC2819] Waldbusser, S., "Remote Network Monitoring Management Information Base", STD 59, RFC 2819, May 2000. [RFC3411] Harrington, D., Preshun, R., and B. Wijnen, "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", STD 62, RFC 3411, December 2002. [RFC4001] Daniele, M., Haberman, B., Routhier, S., and J. Schoenwalder, "Textual Conventions for Internet Network Addresses", RFC 4001, February 2005. [RFC4710] Siddiqui, A., Romascanu, D., and E. Golovinsky, "Real- time Application Quality-of-Service Monitoring (RAQMON) Framework", RFC 4710, October 2006. 10. Informative References [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, December 2002. [RFC4712] Siddiqui, A., Romascanu, D., Golovinsky, E., Ramhman, M., and Y. Kim, "Transport Mappings for Real-time Application Quality-of-Service Monitoring (RAQMON) Protocol Data Unit (PDU)", RFC 4712, October 2006. [RFC3737] Wijnen, B. and A. Bierman, "IANA Guidelines for the Registry of Remote Monitoring (RMON) MIB modules", RFC 3737, April 2004. Siddiqui, et al. Standards Track [Page 36] RFC 4711 RAQMON MIB October 2006 Authors' Addresses Anwar A. Siddiqui Avaya Labs 307 Middletown Lincroft Road Lincroft, New Jersey 07738 USA Phone: +1 732 852-3200 Fax: +1 732 817-5922 EMail: anwars@avaya.com Dan Romascanu Avaya Atidim Technology Park, Bldg. #3 Tel Aviv, 61131 Israel Phone: +972 3-645-8414 EMail: dromasca@avaya.com Eugene Golovinsky EMail: gene@alertlogic.net Siddiqui, et al. Standards Track [Page 37] RFC 4711 RAQMON MIB October 2006 Full Copyright Statement Copyright (C) The Internet Society (2006). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgement Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Siddiqui, et al. Standards Track [Page 38]